In every aspect when starting your small business you should be mindful of making careful, prudent decisions about the allocation of your potentially limited funds — tracking precisely the cost of goods sold (CoGS) against sales to ensure profitability. Every dollar spent is tracked and accounted for, either as an essential cost of doing business (rent, employees, etc.) or as a cost of inventory that will result directly in profit.

I got extra batteries for my cordless tools, but I could never remember which battery was newly charged and which was run down. Now I can easily tell them apart because I painted a number on each battery with my kid’s white nail polish. It dries fast and is— you got it—“tough as nails.” — Tom Baker. Plus: Learn how to double the life of your car battery.
This sturdy 30-in. x 6-ft.-long DIY workbench is the ultimate in simplicity. It’s made from only fifteen 8-ft.-long 2x4s and one sheet of 1/2-in. plywood. Learn how to build a workbench by following the cutting diagrams to cut the parts: Figure B to cut the plywood tops, then Figure C to cut all the framing. Use the lengths provided in the Cutting List (see Additional Information below). You can either screw the framing together with 3-in. screws or hand- or power-nail it together with 3-in. nails. Screw the plywood down with 1-5/8-in. screws.

Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
It all depends on what you care about most. Putting your kitchen by the side door could simplify refilling your water and propane tanks. Putting it behind the driver’s seat creates a nice, open feel in your van. Right behind the cab makes your van more private, while all the way in the back is a different twist on most van layouts out there. Some vanlifers even have kitchens that pull out of the trunk on drawers for cooking outside.
Ultimate Small Shop offers a comprehensive guide illustrating how to set up a workshop. It may be just a small basement shop or a part of the garage converted into a workshop. The guide lays out all the steps and actually caps the investment at under a thousand dollars. Woodworkers can build their workshop for less than $1,000. This does not entail any compromise of tools or the scope of woodworking projects. The guide provides a shopping list including the best tools and there are exact links to find those tools and buy them at the best prices. There are floor plans to ensure layouts are optimized even in the most cramped spaces.

When I change blades on my band saw, I usually need to adjust the thrust bearings and guides with an Allen wrench. I was tired of hunting around for the wrench, so I decided to stick it to the steel housing with a rare earth magnet (neodymium) about the size of a jacket button. Now it’s always handy! — Bill Wells. You can also use a magnet on your ladder.
A software engineer needs to know how to code.  An administrative assistant must answer phones and organize paperwork.  But a marketer typically needs to wear many hats, from writer to advertiser to strategist.  And unlike other job roles, marketing employees can affect the core of a business by changing the way it’s positioned — and they can be held accountable to the company’s bottom line.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
You see, everyone can make money with his/her hobby, and I am going to reveal it to you in a minute… Ultimate Small Shop Ebook Download There are millions of people who have the same hobbies and interests just like you. Everyone is searching for more information about their hobbies and passions. Take a guess – what is the best place to find the information today? I think you will agree that the World Wide Web (the Internet) is one of the best places on the Earth to look for information related to your hobby. Millions of people use the Internet to find the answers to the questions they have, to solve the problems they encounter every day. So, how could you make money with your hobby? It’s simple – build your own web site (online business) about your hobby. Ken Evoy, internationally acclaimed Internet marketer, developed a system – SiteBuildIt! (SBI!) – that helps anyone to create professional websites about his/her hobbies, interests and passions. Hundreds (maybe even thousands) of SBI! users have already quit their jobs and now are making a living from the comfort of their own homes, doing what they love – creating web content about their hobbies. Each web site built by SBI! is search engine optimized. It means that when you build your own web site with the SBI! tools, the traffic to your web pages is guaranteed through search engines. And it doesn’t matter what your hobby is – Ken takes you by hand and explains how you can make money from the traffic received to your web site. What matters is – you create information-rich content pages about what you know and love – about your hobby! Ultimate Small Shop discount If you think that you cannot write web content – forget it, you can! – SBI! will guide you step-by-step from developing your web site’s concept to brainstorming hundreds of profitable related keywords; building a themed web site; generating motivated, targeted search engine traffic that wants to click on your recommendations, links to the related products sold by merchants that you will represent. Note that this is not a “get rich quick” scheme. It will require lots of your energy, work and time. The bottom line is that you will have a hobby that makes money for you!I’ve always liked to make gadgets and gizmos that have some function, either useful or not so useful. It started with the simple things that many kids make – slingshots, a simple bow, and arrow, a toy boat. Occasionally I made more involved items such as a canoe and a dune buggy. Then there was the grass hut – 12 feet across, octagonal in shape, and thatched top to bottom with a thick layer of grass. I built it in a remote location, near a strip mine filled with water. Hauled the cut grass in a 1972 Volkswagon convertible with the top down. Piled the grass high in the back seat. It must have taken a dozen trips back and forth from a nearby hay field. Simple things appeal to me more than costly homemade items. A small project lets me pursue an interest without interfering with other goals. Ultimate Small Shop Tips A project with a small amount of time invested seems more like entertainment.
Just a quick note about light spectrum. I went with 6500k because that’s what I like to film in. The daylight spectrum makes it easier for me if I decide to open the blinds, letting in some natural light. For the average woodworking shop, I think 5000k is probably a good choice, although some folks really enjoy the crispness of a 6500k light. But you should test them out for yourself to see what you prefer.
Love the local history of your city or state? Consider becoming a tour guide. Sure, you’ll need to conduct tons of research to be able to do the job well, but that’s half the fun. Set yourself apart by offering tours that speak to a specific niche of your community’s history. Some tour guides offer historical walking tours of their town’s most haunted spots while others curate guided foodie tours for guests to get a true taste of the city.

Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Fantastic build and opportunity for you. I really appreciate your humbleness given the great asset you have in the new shop. You flaunt/market what you do and where you do it because that’s the business you’re in, but at the same time you understand what a great tool you have in the shop itself relative to what most folks will ever acquire. Well done.
Great video Marc. I know I’m not the first to bring up the reverb in the shop. However I don’t think addition of rubber floor and cabinets will change this much. Furthermore, sound panels look very clunky in my opinion too, but may be necessary above some machines? Materials like drapes and carpet strategically placed can also do wonders, but I don’t know how practical that would be in a wood shop.
The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a con­crete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.
MPG: I'm going to be blunt and tell you that you're not going to find a campervan -- no matter how new or expensive -- that has great gas mileage. When you're driving your home, the miles per gallon are going to be lower than with a typical car. But it's good to ask the previous owner what type of mileage they were getting so you have an idea of what to expect. As a benchmark, our 1994 Chevy G20 got between 15 - 18 miles per gallon. Certainly not great, but there are worse out there.
A grid floor plan, also called a straight layout, is a very efficient use of both floor and wall space. With fixtures and displays running parallel to walls, a grid floor plan maximizes every inch of available floor space, including the corners. Grid layouts are easy for customers to navigate and for store owners to categorize. Plus, they offer plenty of end cap and feature wall exposure for promotional items and seasonal products.
You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
Garage spaces are usually not insulated, and garage doors on most homes have very poor insulation. That means it’ll inevitably be super hot and stuffy in the summer, and freezing cold in the winter. To be comfortable in your workshop you’ll need to take the extra step to insulate your garage and set up some space heaters, and some portable floor or window AC units. Having to wear a heavy coat while you work will impede your DIY efforts and nobody likes working in a sauna.

Ultimately, your workshop should be a place that inspires you to be creative and to do your best work. When you take the time to plan the space for maximum efficiency and comfort, you’ll love spending time there — and that means you’ll get more done, whether it’s fixing up a car or building a new piece of furniture. No matter how you use your workshop, you should enjoy the time you get to work with your hands and make something brand new. So what are you waiting for? Get started designing your perfect workshop today.


I want the shop to be big! Not only do I have a lot of tools, but I tend to frequently bring tools in for testing. As you probably know by now, I also do a lot of filming. So I need a space big enough to allow for full movement around most of the tools. My tripod has a pretty good-sized footprint and having more room allows me to get the best vantage point possible. More space will also allow me to stage larger pieces of furniture, whether for the show or for jobs I take on locally.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 

However, since you may not have "aisles" per say in your store, it's still important to think about grouping products in a way that makes sense from a shopper's perspective. Also, remember to keep "higher-demand" products displayed at eye-level while placing lower-grossing products at the bottom or above eye level. Lastly, It's recommended that you change up these speed bumps weekly or regularly enough to create a continued sense of novelty for repeat visitors. 
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
I think the music comment was about speakers for playing music. I put a few 8″ in ceiling speakers in from MonoPrice.com ($60 / pair I think) and love them. A space that big would probably need at least 3 pairs. You’re not throwing a rock concert with them, but they provide very decent background music for not much cash. The speaker wire from MonoPrice is dirt cheap too. Just add a cheap receiver to drive them. Of course, you probably don’t want to spend that cash at the moment. But it’s a good starting point for the future.

High-velocity fans are also an important tool in their own right, particularly at your finishing station. Increased air flow will help dissipate fumes from paints and sprays for your safety, and you can train a fan on your project to help paint dry more quickly between coats on humid days. To get the most out of your fan, look for floor fans that are easy to aim or wall-mounted fans that will save space in smaller shops.
Keep in mind that if you filed to become a corporation or LLC, then you can skip this step altogether. When you form an LLC or corporation for your business, your business name is automatically registered with the state. However, as mentioned before, if you legally registered your name as Bob’s Bike Shop and would like to conduct business using any variation of that name such as BobsBikeShop.com or Bob’s Bikes, you will need a DBA.
As Kizer & Bender always tell retailers: Put it on paper. If you haven’t settled on your store layout—or even if you have—the first thing you need to do is work your plan out on paper before you start moving things around in your store. Putting it on paper helps give you a clearer picture of the desired result and any potential issues before getting started. Remember, many small retailers find that a mix of floor plan and layout styles works best.
Designing your retail store's interior is a topic that we've been looking at recently in an effort to help boutique merchants be more successful and thrive in today's digital era. From telling your brand's story and creating immersive shopping experiences, to putting together head-turning window displays and signage essentials, when it comes to retail, the devil really is in the details. As such, we want you to help you get the basics down pat. 

The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).
There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior fin­ishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electri­cal and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.
Tired of the rat race, I opted for early retirement. Looking for something to do with all my free time, Ultimate Small Shop Ebook Free I started crafting and am now making a nice supplemental income from it. As a crafter and a businesswoman, I feel I have some valuable insights into the craft business that I can share with you. At some point in your progression from crafting for fun to crafting for fun and profit, you go from handcrafting individual items for yourself and friends to filling quantity orders for a broader marketplace. That’s the time to take a very business-like approach to your craft business. This needn’t be daunting. You don’t need an MBA or management experience – just a bit of common sense. If you’re going to do this for profit, you need to understand Simple, right? But very few people get it. Look at the high failure rate for new businesses. It takes an effort to be successful, but the task is hardly impossible. Traditional craft retailing methods are what most crafters use to get started. They’re the easiest way, especially if you don’t know if anyone will buy what you make. I believe that there is a market for any well-made craft, whether decorative or useful. The problem facing many crafters is how exactly to go about selling them, or more accurately, finding paying customers. The fact is that there is an awful lot of competition out there. My own business got jump-started by my “circle of friends”. Ultimate Small Shop Free My friends noticed and liked my calling cards and began to ask me to design and make cards for them. Starting with just Broderbund’s Create-a-Card program, I was soon earning a nice supplemental income in just a few hours a week. It probably helped that I was retired and live in an area dominated by retirees. But I think that everyone has a “circle of friends” either socially or at work. Of course, you don’t want to impose on their friendship by making a hard sell, but rather use or display your crafts in front of your friends to see if they draw any interest. If they do and if they’re priced right, you’re on your way to craft retailing for profit. If your “circle of friends” market starts extending to friends of friends, you’re probably ready to tap the general marketplace of craft retailing. Most crafters are aware of the periodic craft shows put on by local groups or even by the local Parks Departments. These usually cost little or nothing to join and should give you a fair idea of whether there is any broader interest in your craft. What better way to jump into craft retailing? There are also organized craft shows that tour the country, Ultimate Small Shop Legit most of which charge an entrance fee for participants.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time.  It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years.  During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.  
While a single great product can’t usually support a whole business, it is beneficial to select one or two “headline” products that will form the cornerstone of your offering. This will often be an obvious choice: If you’re a coffee shop, your headline product will be coffee. If you’re a burger joint, you guessed it, it’ll be burgers. This product will often be the centerpiece of your marketing efforts and a way for you to “own” a space in a customer’s mind. For example, Jack’s Burgers makes the best cheeseburger in town and Daisy’s Threads has the most adorable scarves.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
Woodworking isn’t just an overnight hobby, for most it’s a fun pursuit that lasts a lifetime. As your skills develop, the workshop becomes a place not just to build but to repair along the way. In a world where people are strongly influenced by consumerism, there’s a tendency to revert to a throwaway culture. But if you can fix before throwing away, then your tools start to make a return on their investment and have a bigger impact.

Every shop should have good lighting, whether natural or artificial. My video work dictates limited natural light, so I was sure to have plenty of overhead T8 fixtures (6500k). You’ll hear me mention in the video that I was disappointed to see that the ends of the shop were just a little dark. Thankfully, I was able to get the contractor to come back in and drop in 4 more fixtures for me, two at either end. Now the light is bright, crisp, and evenly distributed from one side of the shop to the other.

We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.

Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.

Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
Congratulations !! I think 62 days is quick ! thats a big project. Now that its done and you got to get everything else set up it kinda sucks that you will also need to start making the payments, yuck. However I think it will be a good investment as your show continues to grow . I certainly love it ! I look forward to what you have in store. Thanks
When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress! 
×