This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off serious cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bottom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thickness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop without excessive grunting, so that made it very simple to install. The planer has a significant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
It might sound harsh, but when starting a small business your online presence is crucial. If you speak to some experienced local business owners, many will denounce the existence of online review sites like Yelp and Google Local. They’ll tell you about the added time and pressure they now face to maintain social media profiles for their businesses. A lot of local entrepreneurs will share their bad experiences with online daily deal websites like Groupon. But all that complaining doesn’t change one established fact that the internet isn’t going anywhere.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on. The rewards aren't usually good enough to compel me to purchase on their own. But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
A battery isolator allows your vehicle’s alternator to charge your auxiliary batteries while you drive, and keeps everything separated so you don’t drain your starting battery. Since we installed our Keyline Chargers Dual Battery Smart Isolator, our batteries are almost always fully charged. It’s also very simple to install - the toughest part is running the cable inside your van from the engine compartment.
Remember, your retail store layout guides product placement, directs customer flow, and defines the overall look and feel of your store, so it deserves plenty of thought. Many factors will affect your floor plan choice, including the size and shape of your sales floor, the types of products you sell, and even the customers you hope to attract. Keep these factors in mind as we explore each floor plan option in detail.
These basics are going to set you back about $180, leaving you with $320 left to work with. We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives. This should lead to more consistent results, more enjoyable builds, and increased efficiency. These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
Hi, I have looked through pictures of the shop books. What I am interested in finding is a book with layout design options. I am ready to build a new shop for myself and want to put dust and electrical under the slab. Best layout designs would help me to figure out how to layout a shop that is aprox. 28'x 36'. Is there a book that has this type of information.
Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
“Walk past your Decompression Zone and look to your right. The first wall you see is called a Power Wall, and it’s another key merchandising area. And because it’s one of the first things shoppers see after looking or turning right, it’s a perception builder. Use your Power Wall(s) to display important departments as well as new and seasonal items to create vignettes, tell product stories, and to feature high-demand and high-profit items. (Note: Your store has more than one Power Wall. Stand in various places throughout your store and look around—the walls that stand out are your Power Walls.)”
The first step in choosing a business location has little to do with site evaluation. It’s about understanding who your customers are. What kind of people are they? When and where do they work? How do they spend their free time and extra capital? Get to know your potential customers and you’ll have a far better chance of finding both a site and a property that they’ll want to frequent. Once you know who they are, you need to ask yourself if there are enough members of this target demographic near your intended storefront location. If so, what time of day they are most likely to be near your storefront? And, will it be quick and convenient for them to stop in?
Shops have value on many different levels. There is the satisfaction of having a place to create and work on projects that is hard to quantify, but definitely improves your quality of life. There is the value to your small business of having space in which to work wood and thereby generate income. There is the dollar value of the build itself, which will be a considerable investment and, finally, there is the resale value of your property after you’ve added your shop. Before you go too far, though, it’s worth asking a local real-estate agent about the potential return on your investment in your area; generally shops won’t add significantly to the value of your property, so it’s worth thinking carefully about what else the space could be used for if you were to sell. The decision about whether it is worth it to build is a matter of balancing all these factors: projected sales balanced against the cost; the cost of building is balanced against what it will be worth when you sell. Woodworking can be a creative outlet, can give you a sense of mastery, and even be a way to give back to your community by donating beautiful pieces to local charities for fundraising auctions, or creating pieces that future generations will inherit. Ultimately, the value of a shop might come down to the emotional and social returns that it will pay you and the people around you for years to come.
I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
I used to keep screws in a cof- fee can, but when I reached in with my hand, the screw points pricked my fingers. The can was also a dust and dirt depot. I bought a clear water bottle with a pop-up lid and poured screws into the bottle with a funnel. The screws stay clean, and I can shake them out of the bottle one at a time. — Bruce Burley. Hardware Storage: DIY Tips and Hints
If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based businesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of running into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibilities that your property will allow.
For small business owners starting or wanting to grow a small business, attracting and retaining customers is a huge priority. Let’s face it, without customers you don’t have a business to run. Over the last decade there has been an explosion in the number of high-quality, affordable technologies that are specifically geared towards helping small, local business owners improve the day-to-day operations that impact this aspect of their business. This includes point of sale systems, tax software, bookkeeping software, employee scheduling and payroll programs, inventory tracking tools, customer loyalty programs, gift card technology, ecommerce opportunities, website builders, email marketing software, and social media management tools. The list goes on and on.
So before you start to consider fixtures and displays, think about the product positioning throughout your store. Where are your evergreen, seasonal, limited availability, and sale products going to be featured on an ongoing basis? This process is called product mapping. Following is an example of a product mapping plan that features a mix of product categories in defined areas:
Congratulations on building such an awesome shop. Ultimate man cave! Glad you have a cooperating HOA. I’m currently inviolation of my CC&Rs since I occupy 1/2 of a two car garage and the rules say you can’t use the garage for anything other than your car. So far no violation letters. One thing your missing…a fridge. Looking forward to many more guild builds.
With such an unstable job market and it being harder to get employed, more people are moving into entrepreneurship and being self-employed than ever before. Woodworking is a fantastic business opportunity, but you might feel that you don’t have the space or money to set up your own workshop and sell your goods. If that sounds like you, then you should check out Ultimate Small Shop by Ralph Chapman.
Different approach in that they hung one end of the sleeping platform with hooks and U bolts. One of the best write ups with full details about rigging up an electrical system with second batteries and an isolator, as well as using power inverters. They were then able to incorporate cool things like a mini fridge, lights, and mini PC fans for air circulation.
Plus, taking the time to put pen to paper should benefit you as the small business owner as much as any potential new employee. Creating this kind of central resource about best operating practices will force yourself to formulate your thoughts and be clear about exactly what you want. Whether that means codifying sales procedures or deciding who can take cash from the cash drawer, you’ll have a clear and consistent company policy, something to which most employees will respond favorably.
Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.
Now this Super Pencil from C.H. Hanson does all of that and more. The entire pencil is made from a non toxic graphite composition so the whole thing is a writing surface with no wood around it to shave away. Super pencil marks are water and smudge resistant and because the composite is so durable it never needs sharpening even when you use it on rough materials like concrete.
Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.
The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts.
Assembling parts is easiest when you can work at a comfortable height. But the height of that working surface depends on the size of the project. These ABC boxes, so called because they’re made with sides of three different dimensions, make a variable-height assembly table base. By rotating the boxes or standing them on end, you’ll get three different working heights.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
Keep your air hose and fittings in one place and out of the way. Screw a coffee can onto a scrap piece of plywood. Attach a 2-1/2 in. riser block to the edge of the plywood and hang the entire contraption from a wall or work-bench. Drape your air hose over the coffee can, and store your fittings inside. It also works great for hanging extension cords. — Walter Barndt. Build an air compressor cart.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.
If you have the available time, taking your DIY campervan for a test run (or two) is a great way to identify any problems while you still have access to tools, package deliveries, and a place to work. There’s just a lot that you can’t foresee until you live in your van. Taking it out for some short trips throughout your build will help you understand how you’ll actually use your new living space, what’s necessary, and what’s not.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strapping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.
The good news is that when you’re starting your small business, you now have the tools to take a data-led approach to choosing the right store design. For example: Not sure what type of music gets your customers in the mood to spend? Simply choose a few different styles and display a different one each week. After the test is complete, analyze sales data to help you identify what could be impacting sales. The key to getting accurate results from this kind of test is to avoid switching up the other variables in your store that can impact sales, such as signage, or testing one type of music during a regular business week and another type during a holiday week. For more details on how to create controlled in-store experiments, you can check out Lean Retail 101
I want the shop to be big! Not only do I have a lot of tools, but I tend to frequently bring tools in for testing. As you probably know by now, I also do a lot of filming. So I need a space big enough to allow for full movement around most of the tools. My tripod has a pretty good-sized footprint and having more room allows me to get the best vantage point possible. More space will also allow me to stage larger pieces of furniture, whether for the show or for jobs I take on locally.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code conventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow foundation may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the concrete slab will structurally bear the weight of the shop structure you build above it.
4. Avoid a cluttered look. Owen managed to add more merchandise but avoid a cluttered look by using neutral colors, such as ivory and gray for furniture and larger items. She then accented the space with smaller brightly colored items like vases and pillows. She also makes sure not to crowd her merchandise too closely together. "We try to make it look elegant and give it some space," she says.
Due diligence is the process of going through the current owner’s books with a fine-tooth comb to verify inventory information, sales data, average ticket price, and every other aspect of the business. Doing all this yourself is difficult and time-consuming, so you’ll probably want to involve accountants and lawyers to ensure that you cross all the t’s and dot all the i’s. A big red flag to watch out for here is how intertwined the current owner’s personal expenses are with the business accounts — this can obscure the genuine flow of cash in and cash out of the business. The purchase price of an existing business is often calculated as three to five times the net annual revenue, so you’ll want to take that figure into account before you make an offer.
You may already be aware of something known as the "butt-brush effect," coined by consumer behavior expert Paco Underhill. He discovered that a typical customer, especially women, will avoid going after merchandise in an aisle where they could potentially brush another customer's backside or have their backside brushed. This holds true even if the customer is very interested in a given product. An easy way to avoid this problem is to ensure that your aisle, floor, and displays allow customers to have more than adequate personal space when browsing your products.
Well I think I’ll have plenty of light once we get all of 24 bulbs in place. I’m really glad I saved those old fixtures. Hey another thing we’re reusing, and I’m really glad I saved, is these old cabinets that we took out of a kitchen renovation a couple of years ago. This will be perfect to serve as our base cabinets so that we can build our sturdy countertop on this side of the shop.
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution. Small woodshop workshop on a budget