Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
I didn’t want to get a truck with a million miles on it. I am not a trucker by trade; I got my CDL specifically for this project. I didn’t want to get into a truck and then have to worry about its structure, engine, and transmission—and then start building Optimus on top of it. That’s why I got a brand-new truck custom-built from Western Star to become Optimus Prime.
Most of today’s POS systems have integrated inventory management software that allows you to put hours back in your week, whatever the volume of your stock. A quality point of sale system will allow you to manage pricing changes, track product availability, cross-check inventory, and automate reorders with ease. All of which are crucial in helping you develop a deeper understanding of your business, enabling smoother day-to-day operations and smart purchasing decisions.

You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Note: This article will not include considerations for costs by independent developers or offshore firms. As I have written about cost differences in previous articles, those costs vary widely. Instead, this app cost resource focuses on what it would take to have a quality team of professionals build different kinds of apps. That could be done in-house, by building your own team, or by contracting a third party agency like Savvy Apps.

Some people lean towards starting a small business because they seek freedom, others to fulfill their passions. Some entrepreneurs, however, are driven by a desire to build a legacy, one that that they can hand down to generations to come. Whatever your reasons are for reaching for the stars and aiming for the moon, before you start, remember, there is a dark side.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively win­dowless north walls may be a place to arrange wood storage or mechanicals.
Table mounted routers, planers and shapers are another machine that usually has material fed through, and although they are fairly narrow machines, they require room on their front for material to be fed from, and at the rear for the material to be removed after the work is complete, so again, a space of about ten feet is needed for any significant work.
7. Illuminate your space in different ways. Lighting is important in any retail shop, but it's particularly critical in tight quarters. If a corner of your store is not well lit, that square footage is as good as lost, Langdon says. She recommends using a combination of track lights, lamps, sconces and picture lights. This mixture will not only ensure that your entire space is well lit, but it also will add flair and variety. "Picture lights are amazing. They give a wonderful glow," she says. "Think in terms of layers of light."
Finally, think about the overall color and feel of your workshop. A fresh coat of bright white paint will help your lighting go farther, but you might also consider adding a splash of color for fun. An accent wall or an epoxy floor coating are good ways to upgrade your workshop from drab to fab without adding fussy decorations that will get in the way of business.

But now is the time to take a step back and go on some test runs in your van. Take it out for a weekend here or there (or better yet, a week or more). Try living in it as you expect to on the road. We guarantee there will be things that worked well in your head but not so much in reality. And you’ll come up with random little hacks and innovations that will make your life on the road easier and more enjoyable.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
We've also chronicled how Android and iOS have become more and more similar in their approaches. The "Android tax," as we've referred to it in the past, no longer exists. Generally, Android and iOS apps can now be built with the same quality, with comparable timelines, and budgets. While that doesn't necessarily mean we suggest building platforms in parallel, it's a huge relief for people creating apps.
Once you know your top priorities, you can start thinking about the space each element can take up and where it should go. It is like putting the pieces of a puzzle together when you're working with a small space, so don't get frustrated if it doesn't work out right away. And know that you'll likely have to make some sacrifices. Play with a few options, and choose the one that works best for your situation.

This OXO palm brush really helps us conserve water while washing our dishes. We fill the reservoir with water and a few drops of Campsuds, and we only squeeze out what we need - so it takes care of both the initial rinse and getting our dishes soapy with minimal water usage. It’s also very compact, and the comfortable shape makes it easy to scrub dishes.
If you want that homey cabin feel inside your van, then lining the walls and/or ceiling with tongue-and-groove paneling is a good choice. Paneling looks awesome - the cedar paneling on our ceiling is one of the defining features of our van. And we cut ours to random lengths and stained it several colors to really give it that mismatched, rustic look.

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
So far it has worked out. It's probably not ideal. I imagine a system would work much better, but it gets the job done until then. I ended up setting up in my small 1 car garage as well now. I used two shopvacs to build a system in there. I have a few new Instructables to put together and a new shop tour to do as well. Thanks for the comment! FYI: The wood storage has passed the time test. I have not had to change a thing about it. I plan on adding a shelf above the sheet goods to store thin moldings and cut-offs. I still find it incredibly easy to access my wood quickly with that setup. I have to move stuff around in the garage to get to my wall mounted wood storage, so it's more of a pain.
Thanks again for the inspiration. I've just finished putting the door on my 12x16 shop. Aside from shingles it is ready for the winter. I've yet to cut out the hatch for the lumber or start on the interior, but at least it's weather tight and I can work on the rest I the coming months. I am planning to use mineral wool bays for insulation to mitigate sound and ease installation. I don't see a way to add pictures to this reply (I'm on my phone), so I'll try to add one or two later.
It almost goes without saying that everything about your shop's design should project the right answers to each of these questions. But in today’s market, you have to go one step further. In our digitally connected world consumers have seen it all. The true art of compelling store design is in telling a story about your business, while simultaneously anticipating the needs of your customers. It’s all about the surprise and the delight.
Since the summer of 2013, first time visitors to New York City restaurants have been greeted by window signs boasting a large, capitalized A, B or C. These letters reflect the rating given to each restaurant by the New York City Department of Health and Mental Hygiene (NYCDOHMH). Does the need for government oversight of this industry create an additional administrative and financial burden for the businesses in question? Yes it does. Does the rating system also inform consumers and encourage higher food safety standards across the board? Undoubtedly.
In a small store, these are usually one and the same. In stores where customers don’t shop with baskets, Lesley recommends having a checkout counter large enough to hold products as customers continue shopping. Remember, empty hands pick up more products, and that leads to more sales. Also, make sure checkout counters are large enough to handle the checkout process efficiently and allow space for customers to set down a handbag.
When I change blades on my band saw, I usually need to adjust the thrust bearings and guides with an Allen wrench. I was tired of hunting around for the wrench, so I decided to stick it to the steel housing with a rare earth magnet (neodymium) about the size of a jacket button. Now it’s always handy! — Bill Wells. You can also use a magnet on your ladder.

A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.
Pegboard panels like this are extremely popular way to display and store hand tools. But they have one annoying problem is that when you lift off a tool, often the hook itself will pop out of the board. And that happens with over a number of times, every time you reach for a tool it can get pretty annoying. So you can buy at the hardware store, they make straps and special devices to hold the hook in place, but I’ve found this works just as well and it’s a lot cheaper.
This is about how I built my wood shop. We decided to move from our previous home for a variety of reasons. I saw the move as an opportunity to gain a bigger shop for my wood working hobby. The house we found had everything we wanted, except for a shop or even a garage. It did have a non functioning indoor pool. We thought this space would make a nice wood shop. I could just build a floor over the pool and have a shop. As we got further into the inspection process, it was looking as though fixing the structure over the pool was going to be expensive. It looked like we would have to put a bunch of money into a structure that was not really a wood shop and not a functioning pool either. It made more sense to take out the pool and structure, and then build a wood shop from the ground up. We started this project by regrading our side yard to gain access to the pool in the backyard. Once we had access, we took out the pool. We half filled the hole where the pool was with compacted gravel. I realized that if we sank the shop into the ground I could have the ceiling height I had always wanted in the shop and preserve the view from the house. The design of the shop is a box with a shed roof. The roof wraps down the east side of the structure. I like to think of it as a slightly open toolbox. The entire shop is laid out on a 24 inch grid. The windows and doors fall within this grid. I had a general contractor built the shell and then I built the windows and interior. The interior walls are comprised of a 34 inch concrete stem wall at the base. Above that is a 9 foot, plywood wall. In the space above the plywood wall and below the shed roof is poly carbonate panel to form a clerestory. The tool layout in the shop is divided into 4 areas: an area near the door for material storage and prep, a central area for general wood working, and two areas near the back of the shop, one for turning and one for metal working.
We exhausted our entire life savings on this project and entered into a lot of debt at the same time. And now it’s the ongoing maintenance, repairs, insurance, and upkeep on this rig that make it almost impossible for us to keep it on the road. This is where I’m hoping to get that “let’s sponsor you to travel across America and meet the fans” call from Hasbro or Paramount one day soon.
Well I’ve been kind of fighting that, because I wanted to keep it open to where you could have the flexibility of moving things in and out. It probably makes sense. Actually have another old set of cabinets I thought about putting here, maybe put some really good casters on it to where you could keep it here. I’m also, wanted to be able to store like drum sander, other things that can go under it and then you can take those out and put them on this.

Every shop should have good lighting, whether natural or artificial. My video work dictates limited natural light, so I was sure to have plenty of overhead T8 fixtures (6500k). You’ll hear me mention in the video that I was disappointed to see that the ends of the shop were just a little dark. Thankfully, I was able to get the contractor to come back in and drop in 4 more fixtures for me, two at either end. Now the light is bright, crisp, and evenly distributed from one side of the shop to the other.
In an indoor or basement shop with industrial carpeting, lay down inexpensive laminate flooring to make your life a bit easier at the end of the day. Be sure to anchor the panels or place a large rubber mat beneath to keep them from sliding over the carpet. (Covering up your carpet is even more critical if you want to go beyond wood and work with a material such as aluminum in your indoor shop; metal shavings dig into any kind of carpeting and are incredibly frustrating to clean up.)
It’s hard to overstate the importance of choosing the right location when starting your small business. We’re sure you’ve heard the saying 1,000 times before, Location, Location, Location! Some of the world’s most well-financed franchises have this weaved into their business DNA. McDonald’s Ray Kroc is the perfect example. When asked about the business, this well-know American businessman and philanthropist once stated, “We are in the real estate business, not the hamburger business.”
I live in Northern Va and have the same concerns. I save those little silica gel packets every time they come in a new product and put them in my tool drawers. I also salvaged a dehumidifier from a neighbor that I need to repair and set up in there. I use the wall mounted AC in the summer to keep it cool enough to work in there. Although I haven't gone back yet to insulate the ceiling, it stays really cool in there if i want it to be. 

To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.

Hey, you ever wonder what it look like behind the scenes at a home improvement show? Well here’s a little glimpse of it. This is a storage building I’ve had for awhile and we use this for storage and materials and props we use on the show and it’s also used by my construction company. Well this part of the building has kind of turned into a little bit of a dumping zone, where people just dump things that they’re not sure exactly where they go in the rest of the building.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
Ralph has three decades of professional experience in using workshops and setting them up, and it certainly shows in his Ultimate Small Shop guide. You’ll find all the important information you need to put together your own workshop, including how to save money when putting one together; all the tools and equipment necessary to run a workshop; tips for choosing the best equipment; factors that should be considered when buying things for the workshop; and so much more. If you’ve considered setting up a workshop but feel you don’t have the time, space, or money – then you need to check out Ultimate Small Shop – How to Set Up a Complete Small Workshop on a Budget.
2) I haven’t spent very many nights in full on winter conditions (that 12 degree night in Boise comes to mind!), so I can’t comment too much. It was fine for that… Mostly it was hard transitioning from the warmth of the cab to the frigid air while you are shifting things around and getting ready for bed, but then once you were inside the canopy it was fine. Lots of frosty ice on the inside windows, but in my sleeping bag all was well. It stays a little warmer in the canopy. Maybe I’m a wuss, but I didn’t want to spend an extended period of time dirtbagging it in my truck while I was ice climbing (I spent the first two months in Ouray, CO, sharing a rental), I just thought it would be too challenging/miserable to dry and manage gear in a confined space with the shorter daylight hours. I’d be perfectly content doing future weekend trips with this setup though!
Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
Back in the 1970s and treeplanting in Oregon, I and Tony Lessa lived for two weeks at a time in the back of my 1954 Chevy PU. The canopy was just a simple shell with the board across next to the cab. After the fourth or fifth trip out in the season the accumulated funk was too much. You can imagine two hard-working guys in very muddy and cold conditions coming in after work with dirty wet gear. Pretty desperate circumstances but before Reagan trashed the treeplanting industry our coop ( Hoedads & then Second Growth) was making good money so we endured the hardships. It works for the young. Now, at 76, I find sleeping two of us between the wheel wells in a Dodge G. Caravan (seats removed) much too crowded. I think I will tent and the wife can have the van.
It looks great. Your little guy looks like he's having fun. I just had over 50 kids come through my shop last weekend to do some woodworking for cub scouts. I am saving left over insulation to put in there soon. I restocked my plywood recently too. The pieces of pipe made it much easier to pack in a lot of heavy pieces. I also took the time to measure lengths and mark the ends of all my lumber in the hatch under my bench to find what I need a little easier. My $100 8x8 needs a little TLC soon. But the shop is still rock solid. If you plan on making a lot of dust, I would also suggest a diy air filter with a box fan and a cheap air filter. It helps a little.
One of the core skills needed when starting a small business is the ability to build out a diversified product line that is complementary to the headline product(s). It’s hard to imagine a successful business called “Burgers and Scarves,” right? As a good rule of thumb, a well-thought-out product line allows for the customer to upsell themselves. You want them thinking, “I’m having a burger, y’know what I’m going to have some fries too.”

We love natural light as much as anyone, and the big windows in our van were something we were super excited about. But when you're living in a van, you'll want some privacy. Trust me. You'll also need curtains to keep out the lights when you're trying to sleep. Making your own curtains can seem like a daunting task, but it's not all that hard. (I speak as someone who had to look up a tutorial to operate a sewing machine!)
I'm in the same boat. In Florida, we don't have basements, so my dedicated portion of the garage is 10' x 12'. In that space I have very neatly packed: 8' bench, Cabinet saw with 50" fence, 18" bandsaw, Dust collector, Joint, Planer, Drill press, Compound miter saw and a medium-sized hanging tool cabinet that holds all my nielsen stuff. I find myself moving my stool several times an hour just to work... Can't wait to move into a new house some day!
I framed and sheathed each wall individually and then stood them up with the help of long 2x4 braces.  My neighbor let me borrow his framing nailer, which made things go much faster.  I added a second cap of 2x4 on the top to make the walls a little more rigid.  I then laminated 4 2x4's to construct a ridgeboard.  I nailed in some temporary 2x4 supports and had a friend help lift it into final position.  Once all of the rafters are cut and nailed into place, the supports were removed.
A warning out of concern and love for my fellow 'ablers. A framing nailer is a VERY dangerous tool. Not something to loan out willy-nilly to just anybody. For a small project like this it's just not going to save a lot of time. Most of us are better off burning the extra calories that swinging a hammer uses anyhow. Emergency rooms are seeing a lot of visits because a lot of guys see these on TV and at your big box stores and think they look cool. They are only marginally safer than shooting at the nails with a pistol. (Hmmm...). Be careful, PLEASE.
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood dur­ing a glue-up.
First, let's dump that hand powered saw/miter box.  It gets the job done, but it takes forever.  We're still on a lean budget, but shelling out ~$110 for a 10 inch electric miter saw makes a lot of sense.  This won't be your forever saw, but it should do fine for most projects.  It can handle up to a 4x6 stock which will cover 99% of what a beginning wood worker will throw at it.  
In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
Will this make me money? If it will not, cross it out. If you want to keep it on, please rephrase your goal so the outcome can be money driven. For example: Grow Instagram following (bad) vs. use Instagram to drive traffic and sales to website (winner!). This way, you can break that goal down into tasks ( ill show you that in an another step) and those tasks will lead to you actually making money with that goal instead of with just a larger Instagram following.
Now if don’t have space for a dedicated workbench say in your garage you can build one that folds out of the way when it’s not in use. Simply mount a board to the wall to hinge the table on, then you can use some eye hooks and chain to support it. Now it won’t support a ton of week but it should be just right for a weekend project every now and then.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.
SBA provides support and tools to aspiring small business owners and in particular to minority-owned, women-owned, disadvantaged, and veteran-owned businesses, including a government-backed financing scheme to qualified participants. Local and state authorities also have a range of programs designed to encourage the growth of your small business. Make sure to research your local authority’s website.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.

You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.


Ultimate Small Shop goes beyond the ambit of Amazon, Home Depot and Lowe’s to help woodworkers start their workshop for less than $1,000. Woodworkers will find answers to questions related to the budget, planning, required tools, critical setup factors and more. The guide has been put together by Ralph Chapman, a coach with more than twenty five years of experience in woodworking. Chapman is the small shop expert and what he recommends is not speculation or best case scenarios. He has done it himself. He is now sharing his experience along with expert recommendations so you can begin your woodworking journey right at your home.
Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.
2. Just the basics—I’ve used a compound miter saw, circular saw, jigsaw, band saw, router, table saw, drill, finishing sander, belt sander, Dremel, oscillating multi-tool, bar clamps, and a Shop-Vac. I haven’t used a planer, jointer, or lathe. I’ve never owned a table saw but have used a circular saw or improvised with a router for a few long cuts.
I spent so much time building organizers and filling in just about every square inch on the inside of my shop that I feel it will be better to show some of those in separate Instructables.  I made a couple of video tours to try to highlight some of the different aspects of my workshop.  I hope you enjoy them and I will work on making my future videos more stable.
Hi, I have looked through pictures of the shop books. What I am interested in finding is a book with layout design options. I am ready to build a new shop for myself and want to put dust and electrical under the slab. Best layout designs would help me to figure out how to layout a shop that is aprox. 28'x 36'. Is there a book that has this type of information.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino 

Whether it’s underwear in an apparel store or milk in a grocery store, the items customers need most usually are found near the back. Think about this next time you’re in a grocery store. As you walk to the back of the store to get milk, you funnel past coffee, cereal, and toilet paper. And the milk is right by the eggs and cheese. This is primary and secondary zone merchandising in action, and the reason people shopping for one item often leave with three or more.

Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively win­dowless north walls may be a place to arrange wood storage or mechanicals.
According to store design experts, this is the part of the process where store owners tend to put the cart before the horse. Once the floor plan is sketched out, store owners are quick to purchase and install fixtures, then fill them with product. Far too often, the fixtures chosen aren’t ideal for displaying a range of products in a particular space. Or worse, they don’t offer flexibility needed in valuable display areas that are constantly changing to house featured and seasonal products.
It is also essential to take a lean, data-led approach to choosing a business space. The average length of a commercial lease has dropped over the last few years but is still often well over five years, so the absolute last thing you want to do is rush into a signing and get locked into a bad situation. There are so many ways to test the viability of your business idea before you over-invest and sign a full-blown lease agreement.

Table mounted routers, planers and shapers are another machine that usually has material fed through, and although they are fairly narrow machines, they require room on their front for material to be fed from, and at the rear for the material to be removed after the work is complete, so again, a space of about ten feet is needed for any significant work.


Ultimately, the cost of your coffee shop starts entirely with you. Your coffee shop business concept plays a huge role in what direction you'll go in and what your budget will look like. So if money is an important consideration to starting your coffee business, review what kind of coffee business makes sense to startup at this point and time. We've recently written some articles on low cost ideas for coffee shop businesses.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
It might sound harsh, but when starting a small business your online presence is crucial. If you speak to some experienced local business owners, many will denounce the existence of online review sites like Yelp and Google Local. They’ll tell you about the added time and pressure they now face to maintain social media profiles for their businesses. A lot of local entrepreneurs will share their bad experiences with online daily deal websites like Groupon. But all that complaining doesn’t change one established fact that the internet isn’t going anywhere.
There’s a reason why some of the biggest players online have names that are essentially gobbledegook: Zappos, Skype, Zynga. While there’s certainly some psychological naming principles that often come into play, at the most basic level, it’s simply easier to find this space online and then strive to own the brand name in the minds of consumers. How important this will be to your small business will depend on a number of variables, including your intended size, location, and your desire to exploit ecommerce as well as a local brick-and-mortar business.
The first is that they will need to be powered by a product catalog. Many times that already exists and an app will just leverage APIs or web services to pull back products. If it doesn't, however, it will require either a custom buildout (beware!) or leveraging platforms like Shopify, Magento, or comparable solutions. The strength of these tools include providing the administration interface to add new inventory, APIs or SDKs, ways to store items in a cart, and similar features. The downsides are that you'll be limited by their workflow and customizations.
Hey Kasey, I don’t do anything for insulation, I treat truck camping just as I would cold weather tent camping. Just bring a good sleeping bag and learn how to manage in the cold. Usually the side wall of the truck is not at a perfect 90 degree angle, so you will need to check out the angle and compensate. You can hold up a small piece of 2×4 at the back to judge the angle and make a few test cuts to ensure it sits “flat” aka level.

The key to success here is having clear processes written down, promoting from within whenever possible, and remaining open to change. You’ll want to balance your desire to educate your manager on how to manage your business with an openness to feedback and new ways of doing things. You’ll also want to take advantage of the technology available to keep you abreast of things like real-time sales data for all your locations, no matter where you are.
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie

For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
If you want that homey cabin feel inside your van, then lining the walls and/or ceiling with tongue-and-groove paneling is a good choice. Paneling looks awesome - the cedar paneling on our ceiling is one of the defining features of our van. And we cut ours to random lengths and stained it several colors to really give it that mismatched, rustic look.
Food in bear country… When I was in *real* bear country, like in the Sierras, I always kept my food and scented items in the provided bear lockers. Any of the trail heads or camping areas will have bear lockers. Other than that I never really worried about. Just kept it in the cab, yeah. But the Sierras were the only place I went with any considerable bear problems.

Tired of the rat race, I opted for early retirement. Looking for something to do with all my free time, Ultimate Small Shop Ebook Free I started crafting and am now making a nice supplemental income from it. As a crafter and a businesswoman, I feel I have some valuable insights into the craft business that I can share with you. At some point in your progression from crafting for fun to crafting for fun and profit, you go from handcrafting individual items for yourself and friends to filling quantity orders for a broader marketplace. That’s the time to take a very business-like approach to your craft business. This needn’t be daunting. You don’t need an MBA or management experience – just a bit of common sense. If you’re going to do this for profit, you need to understand Simple, right? But very few people get it. Look at the high failure rate for new businesses. It takes an effort to be successful, but the task is hardly impossible. Traditional craft retailing methods are what most crafters use to get started. They’re the easiest way, especially if you don’t know if anyone will buy what you make. I believe that there is a market for any well-made craft, whether decorative or useful. The problem facing many crafters is how exactly to go about selling them, or more accurately, finding paying customers. The fact is that there is an awful lot of competition out there. My own business got jump-started by my “circle of friends”. Ultimate Small Shop Free My friends noticed and liked my calling cards and began to ask me to design and make cards for them. Starting with just Broderbund’s Create-a-Card program, I was soon earning a nice supplemental income in just a few hours a week. It probably helped that I was retired and live in an area dominated by retirees. But I think that everyone has a “circle of friends” either socially or at work. Of course, you don’t want to impose on their friendship by making a hard sell, but rather use or display your crafts in front of your friends to see if they draw any interest. If they do and if they’re priced right, you’re on your way to craft retailing for profit. If your “circle of friends” market starts extending to friends of friends, you’re probably ready to tap the general marketplace of craft retailing. Most crafters are aware of the periodic craft shows put on by local groups or even by the local Parks Departments. These usually cost little or nothing to join and should give you a fair idea of whether there is any broader interest in your craft. What better way to jump into craft retailing? There are also organized craft shows that tour the country, Ultimate Small Shop Legit most of which charge an entrance fee for participants.
Now that you have your goals mapped out and you know the exact tasks that will help you accomplish them, I want you to pick a day of the week (preferably Monday or Friday) and start planning the week ahead - don’t skip this step, never skip this step. Schedule which one these tasks will happen on what day of the week. So you are literally pulling the tasks from that spreadsheet and placing them into this weekly planner. It’s important to keep in mind deadlines (the ones you set for your goals and when they should be accomplished) and the amount of time it takes you to do a task. You may also want to write down which day it’s due, and who is responsible for this task (if you work with a team).
While not as large as I would have liked (is a wood shop ever big enough?), it is about twice the size of my previous shop. It measures about 12 by 25. Fortunately I had managed to find quite a bit of shelving before the move, so I was able to install shelving along two walls. And the work benches were made from wood salvaged from packing crates from Europe and left over yellow pine car siding and flooring from remodeling the old house.

When starting your small business, the type of business structure you choose will depend on three primary factors: liability, taxation, and record-keeping. Most small business owners begin their commercial life as a sole proprietor because it’s the easiest way to get started. In fact, if you’re in business and you haven’t taken any action to incorporate, you are most likely deemed a sole proprietor by default. You are entitled to all the profits of your business but also responsible for all its debts, losses, and liabilities.
Power outlets are also needed for lighting, heaters, AC units, radios, televisions, CNC machines, 3D printers, and computers—all of which you’ll find in many workshops (although maybe not together, and maybe not all in your garage.) You simply can never have too many outlets and it’s much safer to have too many than not enough. Bring in an electrician to help install your outlets and setup 220v power if needed for larger shop tools.
You are also obliged to file a quarterly tax return which must detail, amongst other things, your employee pay and withholdings. Once again, failure to do this can result in, you guessed it, a fine! As you can see, it’s important to be up to speed on the rules and regulations around taking on employees, including, of course, provisions around hiring foreign workers. The good news is that there are a number of affordable payroll software providers that automate this process very effectively.
Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.
Hi thanks for the info. I’ve got a 2009 tacoma and went with a simple, no screws elevated system. I’ve also got a mx series ARE shell with rack rails so I’ll probably take too much stuff now. Oh well. My question is: how did you attach the plywood to the life gate? My carpentry/construction skills are best illustrated by the “Homer Simpson spice rack”. You used the existing holes in the tail gate, but did you put the tail gate cover back on the tail gate and put the plywood over it and screw thru both or ditch the cover? Thanks
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
At $300, the saw is expensive, but it is one of the more affordable saws that offer a 12 inch blade and a double bevel.  The double bevel allows you to adjust both the angle at which the blade cuts into the wood and the tilt of the blade relative to the workpiece.  Having control over both angles allows much easier cuts of trims and moldings.  It's one of those features that you won't use with every project - but when you do need it, you'll be glad you have it
It might sound harsh, but when starting a small business your online presence is crucial. If you speak to some experienced local business owners, many will denounce the existence of online review sites like Yelp and Google Local. They’ll tell you about the added time and pressure they now face to maintain social media profiles for their businesses. A lot of local entrepreneurs will share their bad experiences with online daily deal websites like Groupon. But all that complaining doesn’t change one established fact that the internet isn’t going anywhere.
Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information. 

If you’ve spent time at your local flea or farmers’ market over the last few years, you may have noticed the explosion that has taken place in the number of innovative small business concepts. From cool new clothing lines to ingenious fusion foods, the sheer diversity of the ideas on display really hammers home one of the key lessons when starting a small business: You need to find your key differentiator. For some this is their brand story, for others it’s the value of their service, but for many quick service restaurants and small retailers, it’s a distinctive core product line that demands the attention and interest of your customers.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
The idea of not having your own bathroom nearby can be incredibly intimidating, but we’ve found that this is actually one of the easiest parts of vanlife. Public restrooms are plentiful throughout North America, and we’ve never not had a bathroom when we needed one. Gas stations, truck stops, Walmarts, McDonald’s - you name it, we’ve done some business there.
You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.
Before starting your small business and opening its doors, it is important to take some time to define your end goal. While it almost goes without saying that this goal will be subject to change, it is only by recognizing and clearly articulating your long-term ambitions that you can provide yourself with a compass that will guide every business decision.
There’s a lot of blood, sweat, tears, and cash that goes into starting and running your own small business. One of the primary benefits of incorporating is that it limits the liability and risk of any losses your business may accumulate along the way. In other words, when you incorporate a business, you are typically not personally responsible for business debts. So if life happens and something goes wrong, as long as you and your business are not legally considered the same, your house, your car, and your goldfish are all safe.
Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.
This holds a lot of stuff but mainly our handheld power tools, so it needs to support a lot of weight. Any shelf in a workshop will probably wind up supporting more than you initially planned so build it as strong as you can and don’t scrimp on the materials or the fasteners you use to hang it. Now the next step is to install our recycled cabinets that will line the wall under the shelf. Now these cabinets are a little plain but that should work great for a shop like this. Even if you don’t own a remodeling company you can usually find these things pretty inexpensively from salvaged warehouses which recover them from renovation projects then resell them to the public.
Yeah, ventilation can definitely be a problem… I’ve just got one window with a screen on it if bugs are an issue–though I haven’t camped in too many areas where they are truly horrendous. Normally I just sleep with the windows/door open to let airflow. I’ve seen some more industrious folks even put in the rooftop fans on their truck camping rigs. Pretty elaborate and beyond my pay grade, but worth searching expedition portal. I like the mesh fly idea if I happen to travel to buggy areas again. Cheers!
Hand tools offer your best chance of finding a real bargain. Until the early 20th century, nearly all woodworking was done with hand tools, and their designs and uses have changed little. Most of the high-end planes on today’s market, for example, are just reproductions of the original designs. And because the originals were mass-produced, they are fairly easy to find at rummage sales and antiques stores. (For more information, refer to Matthew Teague’s article, “Buying Old Tools,” in FWW #180).
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
Many retail fixture and display companies provide store planning and design services to their customers. Though typically not free, these in-house design services can be far less expensive than hiring an independent designer. Plus, they can help streamline the process of store layout and planning, along with the purchasing and installation of displays and fixtures.
One thing I found while looking on the topper websites is a piece of weather strip designed to go between the tailgate and the truck bed. It has a special wedge shape to it so when you close the tailgate it makes a watertight seal. It is just the thing to keep the dust and dirt from entering the back of your rig when driving down the dirt roads. They’re inexpensive too, for a full size truck like my Dodge it’s only $25. It has adhesive on one side, so installation looks simple.

There are a number of woodworking fixtures you can get by without for a long while, but a sturdy workbench isn't one of them. The trouble is, those solid-hardwood benches we all lust after can completely blow a modest woodworking budget. Here's a bench that splits the difference. You'll get a top that can stand up to significant abuse, a sturdy, heavy base that keeps the bench planted where you put it, and an end vise and T-track system for holding workpieces as well as a variety of unique jigs. It may not look quite like a European bench, but it works just as hard as one for a lot less money.


I have been working on building out the space, starting with a new welding table and small material/saw rack. I was able to dedicate a 20' x 28' area to fabrication. I need to figure out some things like angle grinder storage, fume exhaust hood and cold saw set up, but I will get there. Power is one nice thing with a 400A 208VAC 3ph supply panel. Also got the compressor in a sound dampened closet with cooling so the noise level is down significantly. Oh ya, dedicated 15 ton AC for the shop has been nice.
A not for compensation nonexclusive arrangement, on the other hand, gives a tenant maximum flexibility. It’s nonbinding and there are no commissions negotiated. Instead, it gives the broker the right to speak on your behalf and schedule listings for you to see. However, while it provides flexibility, this arrangement gives the tenant broker less of a fiduciary duty.
We did a lot of research and landed on the Bestek 300W Power Inverter. We usually had our devices plugged in while we were driving so they'd be charged by the time we parked for the night. And if we were ever really in a pinch, we would plug it in for 10 minutes with the car off, then another 10 minutes with the car running until it was sufficiently charged.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.
On-demand apps incorporate many of the elements seen in apps with logins and social features. Like ecommerce apps, they also include a transactional component, because users need to purchase goods and services. Unlike social and ecommerce apps, however, on-demand apps essentially require two completely unique user experiences. For example, an Uber driver needs advanced mapping and routing functionality while a rider doesn't. Similarly, the driver doesn't need to do a payment while a rider does.

Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
This sturdy 30-in. x 6-ft.-long DIY workbench is the ultimate in simplicity. It’s made from only fifteen 8-ft.-long 2x4s and one sheet of 1/2-in. plywood. Learn how to build a workbench by following the cutting diagrams to cut the parts: Figure B to cut the plywood tops, then Figure C to cut all the framing. Use the lengths provided in the Cutting List (see Additional Information below). You can either screw the framing together with 3-in. screws or hand- or power-nail it together with 3-in. nails. Screw the plywood down with 1-5/8-in. screws.
The cheapest and easiest way to supply fresh water to your sink is with refillable plastic water containers. There are many styles available, including jerry-can style containers, the extremely common Aqua-Tainer, or standard 5-gallon water cooler jugs. Which one you go with really depends on personal preference and the dimensions of your kitchen cabinets.
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively win­dowless north walls may be a place to arrange wood storage or mechanicals.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
×