A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
I have a plastic bed lining on my truck, which also covered the back of the tailgate… I just popped the screws off, took off the plastic liner and drilled holes in the sheet of plywood to match those used by the plastic tailgate cover. Sorry if that doesn’t help you with your setup. But I’m sure you could just drill your own holes in the metal tailgate. Use the plywood cover as a guide for your screw holes…
“I purchased this book because I'm newly retired and attempting to set up my shop in a home we recently moved to. I'm new to setting up shop and can use some professional advice. Money is always an issue, but more important to me is the subject of time. This book solves both aspects for me. It contains sound advice if you do not wish to overspend on your shop.”
I got extra batteries for my cordless tools, but I could never remember which battery was newly charged and which was run down. Now I can easily tell them apart because I painted a number on each battery with my kid’s white nail polish. It dries fast and is— you got it—“tough as nails.” — Tom Baker. Plus: Learn how to double the life of your car battery.
Once I had the walls completely filled in and trimmed out, I built my doors.  I clamped them in place each day until after I painted.  Then I installed the hinges and hardware.  I decided to change my original plan of building a hinged 4 foot door.  I was worried that the weight of it would cause it to sag over time.  I had also decided at this point to install a small unused AC in the back wall.  I thought that by keeping one of the doors closed, I could keep more cold air in during the hot summers.

I spent a full week grading, compacting the soil and leveling each block before laying the floor joist.  The last thing you want is to finish your new workshop and have a corner start sinking into the ground.  My floor inside my shop is perfectly level still with a 6 foot level.  You can see that I had a drop of about 12 inches on the low side.  During heavy rainstorms, water can flow like a stream next to the fence.  I wanted to make sure my workshop was high enough off the ground to avoid any flooding issues.
This holds a lot of stuff but mainly our handheld power tools, so it needs to support a lot of weight. Any shelf in a workshop will probably wind up supporting more than you initially planned so build it as strong as you can and don’t scrimp on the materials or the fasteners you use to hang it. Now the next step is to install our recycled cabinets that will line the wall under the shelf. Now these cabinets are a little plain but that should work great for a shop like this. Even if you don’t own a remodeling company you can usually find these things pretty inexpensively from salvaged warehouses which recover them from renovation projects then resell them to the public.
Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.

Amenities and Services – You’ll want to understand the full range of amenities offered by a commercial space. These amenities and services may include such things as communal rooms, free Wi-Fi, loading bays and docks, dining options, outdoor space, sewage and utilities, on-site security, and more. The zoning of your business will often dictate the type of amenities and services you require.
The idea behind this segment is to find products that solve common problems we face as homeowners. And the cool thing for me is that I get to learn a lot about the professional side of home improvement. Well, I’m looking for do it yourself items. For example, do you know why carpenters pencils are shaped differently than ordinary round pencils? So they won’t roll off of an inclined surface like a roof. And the larger size allows you to draw fat lines as well as fine ones while you’re marking lumber.
As far as the batten, your actual question..haha. There has not been any moisture or rain make its way through. However, I did caulk all of those joints before I painted. I also made sure I primed all the exposed edges, especially the bottoms of the osb sheeting. You could probably put some pvc j channel along the bottom to prevent rain splash from absorbing up into the end grain. Just make sure you give a way to drain any water that makes it in the j channel. Does that make sense?
Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
Both kids and adults have sat inside [the Optimus Prime truck] and been brought to tears. For many, it is a dream come true. Some kids are very intimidated by Optimus Prime because of the size and won’t go anywhere near it. But I love making people smile. The fact that I can make them smile for just a few minutes by seeing Optimus Prime on the highway means the world to me.
A great product line will also reflect a range of price points. For a business that is working hard to convey a sophisticated and elite vibe, it might be a useful strategy to set a high minimum price, but for the vast majority of small businesses, your pricing should be guided by one key thought: I want every single person who comes through my door to be able to find something that fits their budget.
If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.
“If it’s a retail space then location is critical. Proximity to other retailers, access to transportation, and visibility/signage opportunity can be critical. In this case, there may only be 4 or 5 spaces available that meet the business’s criteria and objectives. A good broker will sometimes develop creative alternatives that might be outside the locational parameters but offer other advantages – such as co-tenancy or lease term flexibility.
If your shop will be attached to your house or another struc­ture, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
Google - If you have any question in the world, you can google it and probably find the answer, lol. However, I know your concern is how accurate the information is that you are getting. You also want to make sure that when you find some great knowledge, that it's leading you in the right direction. So if you google "how to make money from my Instagram following" or "how to drive buyers to my Instagram account", then you want to find actually step by step instructions, that will actually lead to a real result. Sometimes that isn't always the case. So search and try to put the pieces of the puzzle together to help you, but just know that it probably won't be handed to you on a silver platter like my webinars are. If you are having problems with your SEO for google, then I recommend that you get my Google SEO Webinar.
After a year I am still arranging my MAN CAVE . Mine is 2,400 square feet with a 500 sq ft garage and 500 square for room upstairs that serves as gallery of my photos (yes I have several sins) and a conference room as well as any finished projects from the shop. I teach, probono middle school boys and girls in what the school calls an enrichment program. There I have named this the Water’s Edge Woodworking Academy. Actually it is open to my neighbors to build their projects when I am present. I am about one chapter ahead of them. When I told my wife last week I was thinking of an addition she told me “”over my dead body” Taking up extra room are two cnc routers … a Shopbot Buddy Alpha and a Legacy 5 axis cnc machine.
I’m for using what you have got as well but if what you’ve got just really isn’t up to the job it doesn’t hurt to consider switching to something else. Not sure what year your Prius is but if it is fairly new I imagine you could sell it for much more than what an older reliable 4 cylinder Tacoma would cost you. My 2wd Tacoma manual trans gets 30mpg pretty easily and I’m never tempted to get a hotel. The price difference in the two vehicles alone may well make up for the extra cost in fuel and potentially tempting lodging plus even in a 2wd pickup you will have a much easier time going off the beaten path then you will in a low hanging passenger car.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D mod­elling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experi­ment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you antici­pate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.
Right before you start your small business, everyone has a dream setup for their small business in their head, along with a laundry list of amazing features. It’s probably large and full of natural light, opposite from a park, and filled with beautiful details like a long solid oak counter and a little bell over the door. There’s absolutely nothing wrong with these aspirations. In fact, it’s vital to have a clear vision of what you’re working towards. It can, however become a problem if you let the perfect business location become a barrier to opening your doors in the first place.

I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.

It might sound harsh, but when starting a small business your online presence is crucial. If you speak to some experienced local business owners, many will denounce the existence of online review sites like Yelp and Google Local. They’ll tell you about the added time and pressure they now face to maintain social media profiles for their businesses. A lot of local entrepreneurs will share their bad experiences with online daily deal websites like Groupon. But all that complaining doesn’t change one established fact that the internet isn’t going anywhere.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
×