If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.
But now is the time to take a step back and go on some test runs in your van. Take it out for a weekend here or there (or better yet, a week or more). Try living in it as you expect to on the road. We guarantee there will be things that worked well in your head but not so much in reality. And you’ll come up with random little hacks and innovations that will make your life on the road easier and more enjoyable.
Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
I’ve been living out of my Mazda 3—not the hatchback version!— for over two years now. I love the gas savings (standard transmission; I can get up to 40mpg) and the ease of getting around places. I don’t love that I can’t lay flat (hurts the back) and that organization is tricky. However, there are certainly ways to make it work. Ryan linked to one article and there are two others that shed light on some important aspects when going on a long road trip like this.
I know in Missoula the garbage men do not like unbagged dust chips. They sent my friend a warning notice in the mail. Do you pull your drum out to the garbage and let the dust fly or dump it into a bag? My friend has garbage cans with 33 gallon liner which he pulls out of a sealed dust collection box beneath the cyclone… then he uses a hand truck to haul it out to the alley and then puts a fresh can in the box. It seems like a simple dust management method by not handling the dust by either scooping or dumping it out into a bag. I am always trying to think of ways to have less contact with harmful dust particles and I am curious as to how others handle the situation. Have a great weekend!
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
Well I think I’ll have plenty of light once we get all of 24 bulbs in place. I’m really glad I saved those old fixtures. Hey another thing we’re reusing, and I’m really glad I saved, is these old cabinets that we took out of a kitchen renovation a couple of years ago. This will be perfect to serve as our base cabinets so that we can build our sturdy countertop on this side of the shop.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​
I didn’t want to get a truck with a million miles on it. I am not a trucker by trade; I got my CDL specifically for this project. I didn’t want to get into a truck and then have to worry about its structure, engine, and transmission—and then start building Optimus on top of it. That’s why I got a brand-new truck custom-built from Western Star to become Optimus Prime.
While not as large as I would have liked (is a wood shop ever big enough?), it is about twice the size of my previous shop. It measures about 12 by 25. Fortunately I had managed to find quite a bit of shelving before the move, so I was able to install shelving along two walls. And the work benches were made from wood salvaged from packing crates from Europe and left over yellow pine car siding and flooring from remodeling the old house.
For now we’re just getting it out of the room so that our electrician can get started. In any kind of workshop you want plenty of access to power and lots of use of the light. So Mike our electrician is hooking us up. If a service call from an electrician isn’t in your budget you can plan your space so that you can best take advantage of the outlets that are already there. Now Mike has checked all of these surfaces to be sure they can handle these extra outlets he’s adding.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.

Electricity was something we didn’t want to worry about at all in our van, so we went big from the beginning. We bought Renogy's 400-watt solar kit and two VMAX 155ah batteries. We mounted three of the panels on our van’s roof, and the fourth we attached to a folding stand made out of PVC so we could roll it out as needed. While the system works great and keeps us charged up, in hindsight it was a little bit of overkill - especially since we added a battery isolator.


When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.
A lot has changed in recent years. Sophisticated, yet affordable technology now exists that can help track customer relationships from an ad placed on Google, right through to a successful sale. This offers small business owners a unique chance to be entirely data-driven in their marketing approach. Every single aspect of your small business can be tweaked and optimized to ensure that you are enticing customers, up selling where possible, and encouraging people to spread the word about your business.
“Beware suppliers bearing gifts. That ‘free’ refrigerator from the drinks supplier is never really free. You can quickly find yourself tied into sub-optimal deals because of a reliance on this hardware. If you have access to the capital, do yourself a favor: Buy your own fridge and negotiate from a position of strength.” — ShopKeep Founder and Experienced Small Business Owner
Nice video Marc. I did enjoy seeing the details of the construction process. Since becoming a homeowner and a woodworker (something that happened literally at the same time) I have become fascinated with anything having to do with the process of building and finishing and all the details in between. I thought of an off the wall question while watching this video and that is do you write yourself any kind of script for any of your monologues and/or narrating or do you just have a general idea of what you want to say and wing it?

If you dream of devoting your life to a cause you believe in, it might be time to start a nonprofit. You’ll need to incorporate your business and file for 501(c)(3) tax-exempt status -- and then you’ll be required to meet ongoing standards of compliance, but the payoff is making a meaningful impact on a cause you believe in. Want to do good while still making a profit? Consider social entrepreneurship.
I have to agree with these folks....I have a two car garage/workshop that needs to double for ski waxing, bicycle storage and house repairs. I have a Hybrid Table saw, 6" jointer, 13" planer, a shopsmith that serves as drill press, lathe and band saw, dust collector, two work benches...and everything has been designed to roll away, under, above something else...I can set up and tear down in about ten minutes, because at the end of the day, I always have to park two cars in the garage. Always great to look at the great dream workshops, but thought that they should do an article on guys like us, that have to fit several hobbies into one spot. I seem to spend a lot of time planning, and re planning the garage space to try and fit the next tool. I dream about the day I will get a place that I can dedicate to my tools, but until then, I just buy things with wheels.
Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.

Compensation is a critical key to retaining and motivating the right employees. However, since small businesses often start out with tight budgets, compensation is an area they often struggle with, commonly leading to bad hiring decisions that affect overall business performance. The good news is that employers willing to step outside the hourly-wage box have a variety of options.
I look at these workshops and wonder if I'm the only woodworker that has other hobbies that require shop space. My one car garage serves for woodworking, motorcycle storage and maintenance and home repairs. I have a floor standing drill press, Band Saw, 10" cabinet saw, lathe, 6" jointer, 3 tier tool chest(automotive tools only) 4' workbench, mortiser on a pedistal, grinder on a 16" square storage cabinet, and a roll around 40"x22" cabinet that hold my miter saw, portable thickness planer and other storage. Luckily I have an attached shed where I can keep my dust collector and compressor and have them plumbed into the shop. Right now my snow blower also resides in the shop where otherwise my 450cc KTM off road motorcycle would. I need to step outside in order to change my mind so please stop teasing me with these to die for shops. Paul
If you want the ultimate vehicle to customize for your DIY van conversion, the Sprinter is the van for you. They have enough headroom even for tall people to stand up, and enough interior space to design any kind of layout. They also typically have diesel engines, which means greater fuel efficiency and engine life (many diesel Sprinters have been known to make it past 400,000 miles). If you think you’ll be doing a lot of off-roading, the Mercedes Sprinter also comes in a 4x4 version.
You can see in this step how I notched each rafter to fit more securely to the walls.  I also used a metal hurricane strap to secure each rafter to the wall.  Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution.  The walls are a simple board and batten system.  The 1x3 trim covers the joints of the 4x8 OSB.  They make much more high quality sheets goods to use as siding.  However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet.  I sealed the OSB and painted it with exterior paint.  If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed.  It has held up very well over the past couple years and I see no need to spend more money on it now.
Amenities and Services – You’ll want to understand the full range of amenities offered by a commercial space. These amenities and services may include such things as communal rooms, free Wi-Fi, loading bays and docks, dining options, outdoor space, sewage and utilities, on-site security, and more. The zoning of your business will often dictate the type of amenities and services you require.
If you want the ultimate vehicle to customize for your DIY van conversion, the Sprinter is the van for you. They have enough headroom even for tall people to stand up, and enough interior space to design any kind of layout. They also typically have diesel engines, which means greater fuel efficiency and engine life (many diesel Sprinters have been known to make it past 400,000 miles). If you think you’ll be doing a lot of off-roading, the Mercedes Sprinter also comes in a 4x4 version.
Having a plan of action is key to learning how to start and run a successful small business. Whether you are looking for funding from a bank or angel investor, or are lucky enough to completely fund your venture on your own, an articulate and well-thought-out business plan will help you define what your business stands for and what it intends to become over time. As the age-old saying goes: “A goal without a plan is just a wish.” Don’t put your business idea in the hands of fate. Plan thoroughly, give yourself some benchmarks for success and be prepared to innovate as you go.

Thanks again for the inspiration. I've just finished putting the door on my 12x16 shop. Aside from shingles it is ready for the winter. I've yet to cut out the hatch for the lumber or start on the interior, but at least it's weather tight and I can work on the rest I the coming months. I am planning to use mineral wool bays for insulation to mitigate sound and ease installation. I don't see a way to add pictures to this reply (I'm on my phone), so I'll try to add one or two later.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
In an indoor or basement shop with industrial carpeting, lay down inexpensive laminate flooring to make your life a bit easier at the end of the day. Be sure to anchor the panels or place a large rubber mat beneath to keep them from sliding over the carpet. (Covering up your carpet is even more critical if you want to go beyond wood and work with a material such as aluminum in your indoor shop; metal shavings dig into any kind of carpeting and are incredibly frustrating to clean up.)

Now that you have your goals mapped out and you know the exact tasks that will help you accomplish them, I want you to pick a day of the week (preferably Monday or Friday) and start planning the week ahead - don’t skip this step, never skip this step. Schedule which one these tasks will happen on what day of the week. So you are literally pulling the tasks from that spreadsheet and placing them into this weekly planner. It’s important to keep in mind deadlines (the ones you set for your goals and when they should be accomplished) and the amount of time it takes you to do a task. You may also want to write down which day it’s due, and who is responsible for this task (if you work with a team).
Solar Shower. For easy, inexpensive showering in wilderness locations, nothing beats a good solar shower. This is basically a bag of water that you leave out in the sun until it heats up, then hang it from a high place and shower using the attached nozzle. 5-gallon solar showers should get you about 5 minutes of good water flow. There are also pricier but more convenient pump-operated solar showers that you can buy.

One of the most important and often overlooked first steps when starting a small business is preparing a business plan. Many entrepreneurs who hear this might panic. And while the value of writing a business plan is often debated, those who complete them are nearly twice as likely to successfully grow their businesses or obtain capital compared to those who don’t. More on this in part three of How to Start a Small Business 101, Components of a Business Plan.


Hospitality expert, Chip Conley founded and grew the Joie De Vivre hotels from a single San Francisco location to become California’s largest boutique hotel management company. How? He understood the value of a unique vision when it’s consistently applied. He created each hotel to reflect the spirit of a niche-oriented magazine that he felt represented his target market. Examples include the Phoenix (Rolling Stone), the Rex (The New Yorker), Hotel Avante (Wired), Wild Palms Hotel (Fast Company), Hotel Los Gatos (Town and Country), and the Water's Edge (Yachting). Obviously your inspiration doesn’t need to be a magazine, it can just as easily be a song, a group of words, or just a particular image. Find something that resonates with the customers you have in mind and design your store to reflect that vision.
Nice video Marc. I did enjoy seeing the details of the construction process. Since becoming a homeowner and a woodworker (something that happened literally at the same time) I have become fascinated with anything having to do with the process of building and finishing and all the details in between. I thought of an off the wall question while watching this video and that is do you write yourself any kind of script for any of your monologues and/or narrating or do you just have a general idea of what you want to say and wing it?

The time of the travel agent might be passing, but people are still looking for those with a knack for more nontraditional travel coordination. If you always plan the perfect vacations complete with beautiful hotels, the ideal location, and a bevy of delicious restaurants lined up for every evening, consider advertising your services as a more modern approach to travel planning.
Ultimate Small Shop offers a comprehensive guide illustrating how to set up a workshop. It may be just a small basement shop or a part of the garage converted into a workshop. The guide lays out all the steps and actually caps the investment at under a thousand dollars. Woodworkers can build their workshop for less than $1,000. This does not entail any compromise of tools or the scope of woodworking projects. The guide provides a shopping list including the best tools and there are exact links to find those tools and buy them at the best prices. There are floor plans to ensure layouts are optimized even in the most cramped spaces.
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
×