With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.

In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.
Ultimately, I did this to inspire my son. I want him to look at what I have done as a father and be proud. But I also want him to grow up into a strong man who faces fear in the eyes and doesn’t back down because of a challenge. I want him to say to himself one day, “if my dad built Optimus Prime, then I can do anything I want to do in life.”  I want him to succeed in every possible way imaginable, even when I am no longer around to help him through those challenges.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Reactions are typically over-the-top excitement. Everywhere I go, there are people snapping pictures, taking videos, and giving me a “thumbs up.” Sometimes while on the highway, cars will go ahead of me about a mile or so and then pull over to get out and video me driving by them. Truck drivers are always getting on the CB radio asking about the truck.
As far as the batten, your actual question..haha. There has not been any moisture or rain make its way through. However, I did caulk all of those joints before I painted. I also made sure I primed all the exposed edges, especially the bottoms of the osb sheeting. You could probably put some pvc j channel along the bottom to prevent rain splash from absorbing up into the end grain. Just make sure you give a way to drain any water that makes it in the j channel. Does that make sense?

In our opinion, having one of these is an absolute must for living on the road - especially in humid areas. To fully cover the width of a van’s side doors/back doors, you’ll need a larger screen that’s designed for French doors. If your vehicle has a smaller door opening like an RV, a screen meant for a standard door will work fine. We could only find standard door screens, so we bought two and hot-glued them together to cover up our side door.

When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.
×