Because two-sided market apps lack the specificity of on-demand apps, usually more features need to be built. More significantly though, it's much harder for a company to build each side of the market. Uber, for example, is focused on driving. Angie's List, on the other hand, has hundreds of different kinds of service providers. If it wasn't clear from the examples, both on-demand and two-sided marketplaces also have a geographic component. This means that they often start in one area or a subset of areas like Uber did in San Francisco.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
Great website! I spent a summer living out of a ford focus hatchback while road tripping around the United States. The rear seats were replaced with a small platform to store gear and the rear windows were tinted. I enjoyed the freedom that anywhere I parked no one would see me hop from the drivers seat to my platform for some zzz’s. Also no one would guess that someone is sleeping in a 3dr ford focus.
Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.
I will also typically secure those sorts of items under my locked platform if I am gone for a few days in the backcountry, because in reality I could probably care less if someone broke in and stole my box of food, versus someone who stole my clothes or expensive down jackets, which would be much more problematic (and costly) to replace on the road.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but out­side the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials move­ment. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.

Chances are if you’re starting a new small business, you’re not afraid of a little risk. However, it’s also highly likely that you have invested a large amount of money in this new endeavor. It is only prudent to take sensible steps to minimize the impact of unexpected events, like the untimely death of a business partner, a lawsuit from a customer or employee, or a freak accident of nature.
I wanted to have numerous outlets, and have enough elec­trical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
The on the go mode is ideal for when I’m just driving all day and need to pull over and get some rest, be it in a parking lot, a residential cul-de-suc, or wherever. I usually toss a couple of items in the cab of my truck and crawl into the “coffin” sleeping arrangement for a quick night’s rest, but I can also crawl in without placing anything in the cab.
×