Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 

When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.


​There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.

While we think a battery isolator and a 200-watt solar kit provide more than enough power for most vanlifers, some people may want additional ways to generate electricity and charge up their batteries. Especially if you’re planning on running power-hungry electronics like TVs and air conditioners, adding a generator and/or shore power hookups will help you deal with the extra load.
Other than that, you can’t have too much light — especially north light! — and you want accommodations for all the electricity you can imagine. Ceiling fans are a must. A good dust collection system is good, too. Don’t forget to plumb in for compressed air. Do NOT use hard PVC water pipe for compressed air — ever. If/when it breaks or ruptures, it explodes into tiny sharp glass-like shards. I know firsthand. I’ll tell you about it some other time. Think balloon popping!
However, Sprinters are a lot more expensive than other options. It can be tough to find anything reasonably priced with less than 200,000 miles. For the Mercedes Sprinters, parts are more expensive and it may be difficult to find mechanics that have experience working on them (this is less of an issue with Transits and Promasters). And, since these are complex vehicles, they don’t lend quite as well to tinkering as something classic like a VW Vanagon or old Ford Econoline.

If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
Most of today’s POS systems have integrated inventory management software that allows you to put hours back in your week, whatever the volume of your stock. A quality point of sale system will allow you to manage pricing changes, track product availability, cross-check inventory, and automate reorders with ease. All of which are crucial in helping you develop a deeper understanding of your business, enabling smoother day-to-day operations and smart purchasing decisions.
The idea behind this segment is to find products that solve common problems we face as homeowners. And the cool thing for me is that I get to learn a lot about the professional side of home improvement. Well, I’m looking for do it yourself items. For example, do you know why carpenters pencils are shaped differently than ordinary round pencils? So they won’t roll off of an inclined surface like a roof. And the larger size allows you to draw fat lines as well as fine ones while you’re marking lumber.
I framed and sheathed each wall individually and then stood them up with the help of long 2x4 braces.  My neighbor let me borrow his framing nailer, which made things go much faster.  I added a second cap of 2x4 on the top to make the walls a little more rigid.  I then laminated 4 2x4's to construct a ridgeboard.  I nailed in some temporary 2x4 supports and had a friend help lift it into final position.  Once all of the rafters are cut and nailed into place, the supports were removed.
First, try to remove all the extraneous household items that don’t facilitate making stuff. In a perfect world, you wouldn’t have to dig past kids bikes or empty luggage to get to your paint supplies. In the real world though, storage is hard to come by, so you’ll have to give a little to get a little. Consider a line of demarcation in your garage to separate “household” from “workshop.” If you don’t have enough room, consider a smaller-space workbench, or rent off-site storage. You could even build a shed for more covered storage.
Compensation is a critical key to retaining and motivating the right employees. However, since small businesses often start out with tight budgets, compensation is an area they often struggle with, commonly leading to bad hiring decisions that affect overall business performance. The good news is that employers willing to step outside the hourly-wage box have a variety of options.
Now, another thing we’ve recycled that’s kind of unusual, all the wood walls you see here were actually and old backdrop that we used on a show a couple of years ago, perfect for our wood walls we need. Now, to store some of the tools, we have we created this simple little shelf unit out of cedar. And you know it kind of adds some of that warm wood feel to a shop, which I wanted it to look more like this than just plain painted walls.
Time spent earnestly involved in the creation of something designed and made with one’s own ingenuity can be quite enjoyable. So now when I don’t feel motivated to do more practical things I often turn to an idea about some device or other that I’ve wanted to try making but never got around to. Ultimate Small Shop Videos I can recall many such improvised devices that gave me satisfaction and enjoyment.Ideas for things to make come from many places. Most often the idea comes from some need. I do a lot of keying of text using a computer keyboard. I tend to keep the room temperature a bit cool, cool enough that my hands become uncomfortable. I ended up rigging a length of electrical heating tape wound in a large coil-shape to surround the keyboard. Tying the heat tape to a large piece of cardboard keeps it in place. It does a nice job of keeping my hands warm. I can leave the room temperature set where I want it. As far as I know, you can’t buy anything like that. Building and inventing improve my understanding of mechanical devices and materials. It gets easier to manipulate and modify the physical things that are so much a part of everyday living. With effort and imagination, often new devices can be made or existing ones improved for my enjoyment and satisfaction. Both intuition and logic are used to make a homemade gizmo. The more the two abilities are used together, the more powerful the combination becomes. A strong partnership of reason and creativity helps a person to produce and enjoy life. It is fun and satisfying to conjure up and build simple devices. Those created items command more appreciation than more casually acquired, purchased items. And it feels good proving that imagination and ingenuity can make life better. The process of invention seems magical. The mind pieces together what it has already made some sense of into something new. It seems that even the most obscure result can eventually be produced. The grass hut and the keyboard heater each gave me a little taste of that magic. Until recently crafts were usually sold locally or, at best, regionally. Now you literally have the whole world at your fingertips! Some of you may choose a gradual progression from selling to friends to selling at fairs and shows, to retail selling … and so on. Others may decide to jump directly from selling within their circle of friends to the worldwide Internet market – the costs are low enough that this is surprisingly doable. My first career was as a special education teacher. After 15 years of teaching, I earned an MBA degree followed by CFA (Certified Financial Analyst) certification. Ultimate Small Shop Pdf Download After 15 years in finance I was a vice-president and portfolio manager of a major insurance company before I was downsized.
Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D mod­elling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experi­ment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you antici­pate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.

As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.
Find out what tools you need and how to budget for shop setup. Whether you are going to be doing furniture, cabinetry or woodturning, this workshop tools list and budgeting guide can help. Learn how to prioritize purchases of shop tools based on space, interests and cost. Check out a comparison of the workshop tools you can get for $4000 vs. $10,000 and determine how much you need to spend for the shop you want.
Secondly, your size allows you to laser-focus your attention on the right audience. Walmart wants to sell everything to everyone. So maybe instead, you just focus on selling colorful earmuffs to children in the Mission District in San Francisco. This kind of clarity allows you to compete for search rankings on Google, key positions on Yelp and other business recommendation engines, and for space on social media.
Large or small, most retail stores use one of three basic types of retail store layouts. Which type you use depends on the kind of store you have and the products you sell. For example, grocery stores usually use grid layouts because they are predictable and efficient to navigate. Boutiques typically use more creative layouts that allow businesses to highlight different products.

I don’t own a dog, but I have taken my buddy’s two dogs out with us to the trailhead at least. Not sure that I have great recommendations for how you would go about living in the truck with your dog. All we really did was lower the large wooden deck to the bottom position, throw down some soft doggy beds and pillows, then cover it all with a giant blanket which also covered like the side bins to keep dog hair from getting all over. It was nice and cozy for the dogs while driving down the road. Then we just put packs and other gear on/in the side bins. We used some big metal clamps to secure the blanket to the side bins and keep it from falling down or sliding around. I would think avoiding any carpeting would be a good bet, just go with blankets and things than can be taken out, cleaned, and you can sweep out the back.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Pegboard panels like this are extremely popular way to display and store hand tools. But they have one annoying problem is that when you lift off a tool, often the hook itself will pop out of the board. And that happens with over a number of times, every time you reach for a tool it can get pretty annoying. So you can buy at the hardware store, they make straps and special devices to hold the hook in place, but I’ve found this works just as well and it’s a lot cheaper.
Firstly, more and more consumers are rebelling against the generic offerings of big-box retailers and seeking out the unique, personal touch offered by small, local business. You can leverage this message by weaving yourself into the fabric of your community. Canadian yoga apparel retailer Lululemon has enjoyed explosive growth thanks to their ability to do just this. According to their website, “A Lululemon store is so much more than a place to shop. It’s an education centre, a yoga studio and a meeting place. It’s a local hub for educators, ambassadors and guests to gather to learn, sweat and connect. It’s our lifeline to our communities and the soul of our company.” Lululemon uses free events to make people feel that they have a sense of ownership over the brand, and you can too! Getting people through your door is 90% of the battle and event marketing definitely can bring in crowds.
Garages are usually dark, which makes setting up task lighting a priority for a productive workspace. Track lighting is an easy option to install and gives your some directional overhead lighting, but it can cast shadows (especially if the light source is behind you while you work) and you’ll need another lighting source for task and overall room illumination. A simple, adjustable work lamp is helpful for soldering or when you need bright focused lighting.
If you dream of devoting your life to a cause you believe in, it might be time to start a nonprofit. You’ll need to incorporate your business and file for 501(c)(3) tax-exempt status -- and then you’ll be required to meet ongoing standards of compliance, but the payoff is making a meaningful impact on a cause you believe in. Want to do good while still making a profit? Consider social entrepreneurship.
I’m for using what you have got as well but if what you’ve got just really isn’t up to the job it doesn’t hurt to consider switching to something else. Not sure what year your Prius is but if it is fairly new I imagine you could sell it for much more than what an older reliable 4 cylinder Tacoma would cost you. My 2wd Tacoma manual trans gets 30mpg pretty easily and I’m never tempted to get a hotel. The price difference in the two vehicles alone may well make up for the extra cost in fuel and potentially tempting lodging plus even in a 2wd pickup you will have a much easier time going off the beaten path then you will in a low hanging passenger car.

Stop schlepping extensions cords across your garage floor. Make sure your workshop has enough power outlets to charge your tool batteries as well as power your corded shop tools. Your drill press or band saw shouldn’t compete for outlets with a charging drill battery, and you shouldn’t risk tripping over a cable that’s laid across your garage floor.
The key to success here is having clear processes written down, promoting from within whenever possible, and remaining open to change. You’ll want to balance your desire to educate your manager on how to manage your business with an openness to feedback and new ways of doing things. You’ll also want to take advantage of the technology available to keep you abreast of things like real-time sales data for all your locations, no matter where you are.
There is a profound difference between a good idea and a thriving business, but as the saying goes: “A journey of a thousand miles begins with a single step.” At a certain point, turning your dreams into reality is as basic as putting a plan in place and, step by step, making it happen. The good news is that there has never been a better time for starting and learning how to run a small business.
Hi thanks for the info. I’ve got a 2009 tacoma and went with a simple, no screws elevated system. I’ve also got a mx series ARE shell with rack rails so I’ll probably take too much stuff now. Oh well. My question is: how did you attach the plywood to the life gate? My carpentry/construction skills are best illustrated by the “Homer Simpson spice rack”. You used the existing holes in the tail gate, but did you put the tail gate cover back on the tail gate and put the plywood over it and screw thru both or ditch the cover? Thanks
High-velocity fans are also an important tool in their own right, particularly at your finishing station. Increased air flow will help dissipate fumes from paints and sprays for your safety, and you can train a fan on your project to help paint dry more quickly between coats on humid days. To get the most out of your fan, look for floor fans that are easy to aim or wall-mounted fans that will save space in smaller shops.
The other aspect that separates the cost of ecommerce apps is the payment itself. As users add products, they'll need to check out and perform a payment transaction. Some of the tools above bundle in payment solutions. Alternatively, you'll have to integrate with payment gateways like Stripe, Braintree, Authorize.net, etc. Ecommerce apps that fall into this category include Amazon, Stitch Fix, Honest, and many others.
Making sure any holes in your insulation are sealed off and filled helps your insulation really do its job. Great Stuff Gaps and Cracks spray foam insulation is the best way to fill in any space around your foam boards, and to insulate any hard-to-reach spots. You can also spray this into the hollow vehicle frame for insulation (you’ll need a whole bunch of cans for this).
Use the scrap piece of plywood to map out the angle for the speaker stand legs. Decide the height you want for the base of the speakers, and make a mark on the plywood (32 in. for us). Mark the depth of the speaker (13 in.). Lay the 1x4 board assembly on the plywood, lining it up with both the corner of the plywood and the 13 in. mark from the edge. Scribe along the 1x4 board assembly, take the assembly away, and find your angle with a protractor or speed square (17 degrees for us). Cut that angle onto one end of the 1x4 board assembly.
Seems simple right? Well, yes and no. Inventory management can become very complicated once you factor in issues like product lifecycle (how quickly do the apples go bad?), variable amounts of raw goods in a single item (how many apples went into that apple turnover you sold?), delivery times (how quickly you can get new apples?), and variable wholesale apple costs (how much did you pay for that particular bunch of apples?).
For the large square windows near the tailgate I just used those big “magic auto shades” like these, which fit perfectly to cover up those side windows and the back window by the tailgate (I had four in the canopy) and another set up in the cab for my actual window. As for the longer side windows I just used a USPS box, haphazardly stuck up against the window. Nothing fancy.
We did our best to keep costs down, but there was only so much we could do. We needed the shop to go up quickly, which eliminated the prospect of me doing some of the work myself. Additionally, we live in a neighborhood with a homeowner’s association. This means we have very specific restrictions for what we can and can’t do on our property. So the shop must have all of the same finishing touches as our house.
When you’re first starting out, it can be hard to imagine that there are entrepreneurs out there complaining of having grown too fast. But for some, it’s not a problem that’s welcome. For every Ben and Jerry’s, (Ben Cohen and Jerry Greenfield turned a rundown Burlington, VT gas station into an ice cream empire), there’s a Zynga or a Living Social that has enjoyed incredibly fast-paced growth, let their operating costs get out of hand, and then had to engage in mass layoffs when reality hit. If you’re enjoying fast-paced growth, make sure that this is reflected in your operating margins, not just the metric of revenue. You don’t want to be the butt of the old retail joke: “We’re losing a buck on every sale, but we sure are making it up on volume!”
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
As far as the batten, your actual question..haha. There has not been any moisture or rain make its way through. However, I did caulk all of those joints before I painted. I also made sure I primed all the exposed edges, especially the bottoms of the osb sheeting. You could probably put some pvc j channel along the bottom to prevent rain splash from absorbing up into the end grain. Just make sure you give a way to drain any water that makes it in the j channel. Does that make sense?
Have a walk-through yourself and see where the visual cues guide you or get your staff, friends, or family to do the same and give you honest feedback. Don't forget to observe your customers and see what they're drawn to, what they avoid, and how they move, then match that with your intended design. If you keep resilient and keep your eyes and ears open, you'll be sure to create a retail design that's a win-win for both you and your customers. 
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.

Now, we’ve already applied some resurfacer to fill up some of the deeper holes and after that dries overnight we’ll use a floor leveling compound tomorrow morning to really smooth everything out. Leveling compound is more fluid than the resurfacer so it flows into all of the low spots to even out the surface. Now, this won’t look like a finished floor when Tim’s done but it should do the job for our shop. Now, while he wraps up this Emily has a Best New Product that might be a great addition to your workshop.


Now, another thing we’ve recycled that’s kind of unusual, all the wood walls you see here were actually and old backdrop that we used on a show a couple of years ago, perfect for our wood walls we need. Now, to store some of the tools, we have we created this simple little shelf unit out of cedar. And you know it kind of adds some of that warm wood feel to a shop, which I wanted it to look more like this than just plain painted walls.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
If this all sounds too complex for you, there are alternatives. Thanks to advances in technology, there are tools available that help simplify bookkeeping and accounting so that you don’t have to hire a full-time accountant to take care of the basics. We’re big believers that a technology-led approach to running a small business will leave you with more actionable insights, more time to focus on your day-to-day operations, and ultimately, more money. For details on the cloud-based technologies that more and more businesses are relying on, make sure to check out our cloud-based business guide.
Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
At least once a year I want you to set aside some time (I’m talking about a large chunk of time - like a day) and I want you to write down everything you want to accomplish this year or next year (or whenever you are planning for). I tend to plan for a whole year, but you can try 3-6 months to help you get started. Take away any and all distractions because it’s important that you are super focused on what you want to accomplish for the year. This is the time to let your ideas flow, don’t hold back. Things on this list can include: Launch your own website, release a new invitation line, and work on my Instagram account. Don’t overthink, just write down what comes to your mind and whatever your heart desires. There will be time later to refine what you have written down. When you are starting to brainstorm your goals, I would suggest that you first start off writing them on a notepad like this. And then once you are done, you can move them over to a task organizer like this.
Whether you build or buy your workbench, it must be designed and constructed to withstand the rigors and pounding you’ll put it through. The base and legs should be sturdy and the table should not easily be knocked over. The top should be durable and not easily dinged or dented. Make sure your workbench is made of a material appropriate for your types of projects, too.
However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
Hey Marc. Just wanted to send a huge congrats your way for this milestone. It’s been pretty awesome to follow you on this journey since I discovered you on iTunes some 5 or 6 years ago. Mad props for what you’ve done to grow and enhance the online woodworking community as well as woodworking as a whole. I think with todays generation (as well as future generations) growing up behind a computer, the work that you and the rest of the podcasting world do will go a long way towards bringing new people into the craft. I hope that in the future you are able to start a series of videos showing how you introduce Mateao to the craft. Keep up the awesome work!
To help, I’ve pulled together 40 small business ideas for anyone who wants to run their own business. Use these as a jumping off point to spark your own unique ideas.And if all else fails, live the words of Airbnb Co-founder Brian Chesky: “If we tried to think of a good idea, we wouldn’t have been able to think of a good idea. You just have to find the solution for a problem in your own life.”
Thanks! Yep, the canopy clamps and the grooves in the bed liner are the only things holding the side shelves and sleeping platform in place. You just pop off the clamps with a ratchet and the whole things lifts out / slides out easily. That’s what I did to treat the wood after construction, takes maybe 15 minutes to pop out. Very modular. It’s been in there for more than two years now, same wood, and everything is still looking good and working fine. I like it!
First, let's dump that hand powered saw/miter box.  It gets the job done, but it takes forever.  We're still on a lean budget, but shelling out ~$110 for a 10 inch electric miter saw makes a lot of sense.  This won't be your forever saw, but it should do fine for most projects.  It can handle up to a 4x6 stock which will cover 99% of what a beginning wood worker will throw at it.  
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
Location, location, location is quoted so often for a reason. When starting a small business, the wrong choice could hurt your business before you’ve even had the chance to open the doors. Take the time to really understand your customers and do everything you can to gather real world insights that will help you determine the viability of your potential new space.
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
On a more mundane, but equally important note, the costs of retroactively fixing errors in a name choice or a business structure can be enormous, both in your time and in real-terms. It is therefore important that you do your research and establish the correct legal structure for your business early on. Still not sure what steps you need to take to incorporate your business? Visit BizFilings.com to learn more about the first five steps you need to take when incorporating your business.
Making sure any holes in your insulation are sealed off and filled helps your insulation really do its job. Great Stuff Gaps and Cracks spray foam insulation is the best way to fill in any space around your foam boards, and to insulate any hard-to-reach spots. You can also spray this into the hollow vehicle frame for insulation (you’ll need a whole bunch of cans for this).

If you’re starting a small business for the first time, your new best friends in life should be your bookkeeper and your accountant. The former should be engaged for a few hours every week (especially at the start of your business) to compile your books and ensure your records are maintained to the required standard, while the latter will help review your tax situation and prepare financial statements. Both can also be used as invaluable sources of actionable intelligence about ways to reduce costs, increase margins, and generally streamline your finances.You’ll be able to spend all that time you save doing what you love and thinking strategically about your business.
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
×