For years my wife and I had agreed that we would one day leave Oklahoma for someplace we really loved. That day finally arrived last year when we found a home in Vancouver, Washington that met our dreams. Only thing missing was someplace for a woodshop. Well, there was a place, under a deck, but not a room. So, as part of the move we had a local contractor build a room that would one day be the wood shop. Fortunately there was already a door from the house into this area, and about half of the “walls” were there, in the form of concrete retaining walls.
You may already be aware of something known as the "butt-brush effect," coined by consumer behavior expert Paco Underhill. He discovered that a typical customer, especially women, will avoid going after merchandise in an aisle where they could potentially brush another customer's backside or have their backside brushed. This holds true even if the customer is very interested in a given product. An easy way to avoid this problem is to ensure that your aisle, floor, and displays allow customers to have more than adequate personal space when browsing your products.
While an electric miter saw is a convenience, it is not necessary to do good work.  A quality electric miter saw will run around $150-$200, that by itself would destroy our budget.  A hand saw with a miter box does the job just as well at a fraction of the price.  This highly rated Stanley version for ~$60 should get the job done, albeit with a bit more elbow grease.
I live in Northern Va and have the same concerns. I save those little silica gel packets every time they come in a new product and put them in my tool drawers. I also salvaged a dehumidifier from a neighbor that I need to repair and set up in there. I use the wall mounted AC in the summer to keep it cool enough to work in there. Although I haven't gone back yet to insulate the ceiling, it stays really cool in there if i want it to be.
Making sure any holes in your insulation are sealed off and filled helps your insulation really do its job. Great Stuff Gaps and Cracks spray foam insulation is the best way to fill in any space around your foam boards, and to insulate any hard-to-reach spots. You can also spray this into the hollow vehicle frame for insulation (you’ll need a whole bunch of cans for this).
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
Well I think I’ll have plenty of light once we get all of 24 bulbs in place. I’m really glad I saved those old fixtures. Hey another thing we’re reusing, and I’m really glad I saved, is these old cabinets that we took out of a kitchen renovation a couple of years ago. This will be perfect to serve as our base cabinets so that we can build our sturdy countertop on this side of the shop. 

Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.
Amenities and Services – You’ll want to understand the full range of amenities offered by a commercial space. These amenities and services may include such things as communal rooms, free Wi-Fi, loading bays and docks, dining options, outdoor space, sewage and utilities, on-site security, and more. The zoning of your business will often dictate the type of amenities and services you require.
Garages are usually dark, which makes setting up task lighting a priority for a productive workspace. Track lighting is an easy option to install and gives your some directional overhead lighting, but it can cast shadows (especially if the light source is behind you while you work) and you’ll need another lighting source for task and overall room illumination. A simple, adjustable work lamp is helpful for soldering or when you need bright focused lighting.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done. 

My advice here is to make a detailed list of what the various parts of the build will be (drawings, permits, foun­dation, framing, electrical, etc.) and decide what you would like to do yourself and what you will need to hire others to do. Get quotes on the work that you would like to hire out and estimate the materials you will need to do your por­tion. You may want to factor in your time into the cost as well, especially if you will be passing up other income to work on the project. At some lumberyards, you will be able to give detailed drawings to an estimator on staff who will do a material takeoff list for you of what you’ll need and what it will cost. When all the numbers come in, you can put together a budget and plan for an overrun allowance of around 15 percent. If you keep track of the materials and subcontract costs as you go, you can stay on track and make decisions as you go about the latter stages of the project without regretting it later. If it is challenging to obtain fund­ing for a complete build, you may want to stage the build so that initially the frame goes up and the exterior is finished, and then you finish the interior work as you have time or as funds become available.
I want the shop to be big! Not only do I have a lot of tools, but I tend to frequently bring tools in for testing. As you probably know by now, I also do a lot of filming. So I need a space big enough to allow for full movement around most of the tools. My tripod has a pretty good-sized footprint and having more room allows me to get the best vantage point possible. More space will also allow me to stage larger pieces of furniture, whether for the show or for jobs I take on locally.
In as much as I am a clamp freak, I needed some way to organize clamps without spending a mint on brackets. In our previous house we had a number of glass shelves –which I didn’t plan to put up here. But, the brackets were great – I laid in two tracks next to each other, then took a pair of the shelf brackets, cut a piece of 9/16 x 9/16 x 3 inch pieces of wood – put the wood between the brackets, shrunk wrapped around the brackets and wood, and came up with some really stable clamp hangers.
Ideas on how to Improve your Workspace – We can all do with some ideas on optimizing workspace. The guide has a lot of information about how to improve your workshop to be more efficient and improve workflow. This includes the costs of improving your shop, as well as hacks you can do yourself to improve efficiency and storage space for less. You’d be amazed at what you can do with even a small room. You just need someone to point you in the right direction.
If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.

I used to coat my metal table saw and planer bed with auto wax because it makes the wood slide nicely across the metal. But then I saw an expert cabinetmaker use wax paper, and now I do the same. I keep a roll in my shop drawer and rub a sheet of it over the metal beds on my table saw, router, planer and disc sander. The wax coating doesn’t last as long as a good paste wax, but boy, is it a lot easier and quicker. — R.J. Hayes. Plus: 22 clever new uses for your tools.
To avoid buyer’s block, define the core characteristics you absolutely need in your business. Write them down in a prioritized list ranked from ‘deal breaker’ to ‘would be nice to have.’ Now cross off the bottom five and focus only on the ones that are left. Compromising is essential in choosing a commercial space, especially in popular neighborhoods. Besides, you’d be surprised how what once seemed like a less than stellar storefront can become your dream location once you get those creative juices flowing.
At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!
Once again I would like to Thank You for letting so many of us see what is going on in your world. It is very educational and entertaining to see what has happened in the past few months of your dream shop build. As I was watching the video I periodically looked out my window to see the snow falling steadily and building up along the windowsill. Every now and then I imagined I was in your sunny backyard admiring your Shop. I am looking forward to seeing what you will create in your New Space. Keep up the Good work and Congratulations on your Dream Shop.
At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!

It’s no accident that some of the best marketers in the tech startup industry are known as “growth hackers.” Think about your target demographic (e.g. students, local mothers, teenagers) and find any way you can to get the word out to them. Email mommy bloggers, hand out free samples at the local college, or write your website on all the napkins you hand out with your food. There is no substitute for action.
Now, this is kind of an odd situation here, a few years ago when we bought this building there was a concrete block wall around here and a large drain right in the middle of the floor. Well the drain will certainly come in handy for any cleanup in the shop but the walls kind of left us when we removed those kind of left us a little divot and a little bit of damage here, so to make this nice and smooth so that our rolling workbenches will roll around real nicely we’re having to do a good bit of floor patch.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
If you’re moving into a space that requires renovations in order to fit your business needs, you’ll also want the landlord to take on responsibility for that work. We’re not talking aesthetics here, we mean necessary renovations such as improved data connectivity. If you have to do the work yourself, it’s advisable to ask the landlord for a rent-free or reduced-rent period. You should also make sure that any additional alterations you have in mind are acceptable and would not be in breach of the lease. Last but not least, always make sure the do’s and don’t of what can and cannot be done is put in writing, it will save you a lot of headaches later.
Well I was just thinking about all of the supplies I’ll be able to keep in this large shelf unit we just installed in our workshop. Hey, that’s we’re doing this week is creating a very practical realistic workshop where we’ll be doing a lot of projects for the TV show, but it’s also going to be used by my construction company so it really has to be set up properly.
Becoming a small business owner is one of the most rewarding and inspiring journeys a human being can take. It provides you with a chance to be your own boss, take control of your financial destiny, and become a meaningful contributor to your local economy and community. There will always be a reason not to take the plunge. But if there is one rule of small business — and life — is that nothing will happen if you don’t make it happen.

The level of sophistication in a $250 shop is significantly less than a $2,500 shop.  But keep in mind even a $2,500 budget is entry level.  Acquiring a shop full of the perfect tools for each and every job takes a life time.  But that doesn't mean that producing quality work takes a lifetime.  One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.


As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
Calculating the size of your desired parking lot is easy. The rule of thumb is to have a parking spot for every three customers. Determining traffic is trickier and potentially more lucrative. To help, we wrote an article on how to calculate your desired foot traffic. If you want to calculate your desired vehicle traffic, you can refer to our article on how to choose a location for your restaurant.
Solar Shower. For easy, inexpensive showering in wilderness locations, nothing beats a good solar shower. This is basically a bag of water that you leave out in the sun until it heats up, then hang it from a high place and shower using the attached nozzle. 5-gallon solar showers should get you about 5 minutes of good water flow. There are also pricier but more convenient pump-operated solar showers that you can buy.
Although the market has even more options to build apps now than in 2015, there's also clearly more of a distinction in quality. The best app firms and app developers have further honed and distinguished themselves. They have more awards, stronger portfolios, better team members, and more specialized skills. The tools available have made it easier to build apps though, so there's also many more mediocre or low-quality options to build your app.
Shops can range from functional spaces adorned with unpainted wallboard to beautifully finished, painted, and trimmed-out spaces. Ultimately, I think it depends on your budget and how important your surroundings are to your mindset as you’re working, or to your clients’ if they will be viewing your shop. If finishing your shop will improve the quality of the work that you will produce, thereby relaxing or inspiring you, or showcase for your clients the quality of the work of which you are capable, it may be a worthwhile invest­ment. A more finished space may also allow for activities like parties or even a weekly poker game (as long as drinks stay off the tools).
Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D mod­elling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experi­ment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you antici­pate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.
With the third category, franchise businesses , the risk of getting started is potentially the lowest of all when it comes to starting a small business, as you are often buying into a clearly established business model. You will also often benefit from the initial support of the franchisor, including advice around site selection, training and orientation, employee hiring, and product mix coordination. This support and assurance, however, comes at a premium. On top of the normal startup costs (space, equipment, etc...), you’ll have to pay a franchise fee to the owner, which is often tens of thousands of dollars, as well as a percentage of your revenues on an ongoing basis.
Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
Love the local history of your city or state? Consider becoming a tour guide. Sure, you’ll need to conduct tons of research to be able to do the job well, but that’s half the fun. Set yourself apart by offering tours that speak to a specific niche of your community’s history. Some tour guides offer historical walking tours of their town’s most haunted spots while others curate guided foodie tours for guests to get a true taste of the city.

Table mounted routers, planers and shapers are another machine that usually has material fed through, and although they are fairly narrow machines, they require room on their front for material to be fed from, and at the rear for the material to be removed after the work is complete, so again, a space of about ten feet is needed for any significant work.
In order to ensure that the staff you’re bringing on board is the right fit for your small business, there’s a few questions that you should ask yourself during the interview process. Are they competent? Capable? Compatible and committed to your core business values? Do they fit in with the culture you are trying to build? And can you offer them fair compensation? Business expert and entrepreneur Alan E. Hall, calls this the 7 C’s to hiring. At the end of the day you want to look beyond the skills and experience they have on paper and make sure that they are willing and able to grow with your business.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
I don’t think you have run into this problem, but I have to deal with condensation in the cap as I live in a moist climate. I was thinking of an old van type roof vent with fan for active ventilation, or drilling holes along the side of the cap, inserting short cuts of pipe with fine screens (mozie land), and capping them. This way I could control for rain, cold, etc., but create some passive cross ventilation at roof level.
I was really excited after seeing your shop video. It was almost like you read my mind (except my plans does have more windows and a wood burning stove as I live in TN). I realized the importance of more 22o plugins after you explained your reasoning. I was just planning a couple. Love the floor and ceiling plugins. One quick question. Is each plugin area on it own breaker, or do you have more then one on each breaker. I was planing on each one to have its own breaker. Love your approach on your projects and how you introduce new items or products. Thanks and Merry Christmas
If you’ve been to gem shows, you know how overwhelming and daunting they can be. Although it’s difficult to narrow down all those tempting options, your jewelry business profit margin will be greater if you plan ahead and focus on shopping for a particular line and color scheme of jewelry. Ultimate Small Shop Online Review You must keep the bigger picture in mind and try to keep your emotions out of the design process. Here are some tips for defining your market and researching it so that you can walk in and out of a gemstone show feeling confident in the business investments you’ve just made. Gemstone shows and fairs are marketplaces for vendors of gemstones, findings, jewelry supplies, and tools. Due to a large amount of competition between the vendors, prices tend to be competitive. I’ve found unbelievable deals on high-quality gemstones and findings at gem shows. To find gem shows near you, you can simply do a Google search for “gemstone show” or “gem fair”. Other sources of information are your local convention and visitors’ bureau and any lapidary clubs in your area. Anyone can attend most gemstone shows. Although you don’t usually need a wholesale license to get in, some vendors may ask for your resale permit before letting you buy at wholesale prices. Show admission fees tend to be in the $5 to $10 dollar range. What market are you trying to target with your jewelry? Don’t try to please everyone. Ultimate Small Shop does it really work Are you trying to appeal to individuals like yourself? What age bracket are you trying to reach? Does your jewelry line appeal to funky or traditional individuals? Next, take a trip to your local department store and take note of the colors that are being used for the upcoming season. Look at the jewelry and observe the lengths of the earrings/necklaces, the sizes of the stones, and the other various style elements for the season. While your designs should not be copies or replicas of the jewelry in the stores, you can simply incorporate the observations you make into your own original design ideas. Fashion and jewelry magazines are also a great place to find out what trends are coming into the stores. There will be an overwhelming array of gemstones and supplies at the show. Having a jewelry line style and color scheme in mind will allow you to narrow your focus. Vendors will offer gemstones in more shapes, sizes, cuts, and colors than you can imagine. Stick to the colors you’ve mapped out for yourself and walk through the entire gem show once before buying anything. Jot down and compare the prices of items that you’re interested in. Then take a break, go outside for some fresh air, and reflect on the items you saw and really liked. Then review your budget and the jewelry line you have in mind before returning into the gemstone show. Ultimate Small Shop Guide Download This will help you get the best deals on the items you’re most interested in so that you don’t blow your budget or become overwhelmed by the options. Soaring through the air, watching the clouds and the birds fly by.

I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.

A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
In today’s competitive business landscape, the key card that small business owners hold up their sleeve is their ability to offer something distinctive, original, and personal. As small businesses grow, however, it can become increasingly difficult for the time-pressed, financially strapped entrepreneur to maintain direct oversight over every aspect of their store.
In many ways, skoolies are the ultimate in mobile living. The big advantage here is space - there’s tons of room for couches, beds - even a full bathroom - and you can easily accommodate families and other larger groups. There are also some really impressive skoolie builds out there that are nicer than actual houses, and it’s a whole lot cheaper to convert a bus than to buy a similar-sized RV. Skoolies come in multiple sizes, from “shorties” to full-sized buses.
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution. Small woodshop workshop on a budget
×