Trademarking is a lot less expensive than most people think (although enforcement is another thing entirely), but make sure to do your research! If someone else is already using your proposed name, your application will be rejected right away and you will not only lose your application fee, but the time invested would have been in vain. And as you know, time equals money.
I spent a full week grading, compacting the soil and leveling each block before laying the floor joist. The last thing you want is to finish your new workshop and have a corner start sinking into the ground. My floor inside my shop is perfectly level still with a 6 foot level. You can see that I had a drop of about 12 inches on the low side. During heavy rainstorms, water can flow like a stream next to the fence. I wanted to make sure my workshop was high enough off the ground to avoid any flooding issues.
Keep your air hose and fittings in one place and out of the way. Screw a coffee can onto a scrap piece of plywood. Attach a 2-1/2 in. riser block to the edge of the plywood and hang the entire contraption from a wall or work-bench. Drape your air hose over the coffee can, and store your fittings inside. It also works great for hanging extension cords. — Walter Barndt. Build an air compressor cart.
These basics are going to set you back about $180, leaving you with $320 left to work with. We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives. This should lead to more consistent results, more enjoyable builds, and increased efficiency. These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
The enormous range and affordability of options has provided the chance for small business owners to apply technology to their accounting, marketing, and day-to-day operations. You can spend less money, save valuable time, and gather data about almost every aspect of your business. What’s more, you can enhance the way your customers experience your store in a meaningful and cost-effective way.
I’m picking up a 4×4 Extra cab pick up tomorrow and selling my current 97 Tacoma. It’s older and it’s got a lot of miles but it still has a lot left to go. Mine is available in the 3 grand range. They’re hard to find and all the rust free trucks are out here in the west but mine is one example of many good Tacos that are available at an affordable price that will fit the bill perfectly.
A battery isolator allows your vehicle’s alternator to charge your auxiliary batteries while you drive, and keeps everything separated so you don’t drain your starting battery. Since we installed our Keyline Chargers Dual Battery Smart Isolator, our batteries are almost always fully charged. It’s also very simple to install - the toughest part is running the cable inside your van from the engine compartment.
Small business owners can maintain steady, manageable growth by keeping a firm eye on costs and always aggressively looking for ways to increase sales and grow their brand. It can be difficult to empower staff and managers around you, especially if you’ve spent a long time steering the ship alone, but it is an essential part of successful expansion. Stay open to suggestions from your managers while making your current business best practices clear to them.
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
Yeah, ventilation can definitely be a problem… I’ve just got one window with a screen on it if bugs are an issue–though I haven’t camped in too many areas where they are truly horrendous. Normally I just sleep with the windows/door open to let airflow. I’ve seen some more industrious folks even put in the rooftop fans on their truck camping rigs. Pretty elaborate and beyond my pay grade, but worth searching expedition portal. I like the mesh fly idea if I happen to travel to buggy areas again. Cheers!
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.
If you have some experience under your belt, put it to good use as a life or career coach. Many of us are looking for guidance in our careers -- and finding someone with the time to mentor us can be tough. Life/career coaches don’t come cheap, but they are able to offer clients the intense and hands-on training and advice they need to make serious moves in their personal and professional lives. After all, sometimes everyone just needs some uplifting advice.
One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks!
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteriously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
It might sound harsh, but when starting a small business your online presence is crucial. If you speak to some experienced local business owners, many will denounce the existence of online review sites like Yelp and Google Local. They’ll tell you about the added time and pressure they now face to maintain social media profiles for their businesses. A lot of local entrepreneurs will share their bad experiences with online daily deal websites like Groupon. But all that complaining doesn’t change one established fact that the internet isn’t going anywhere.
Buying rough cut lumber saves a ton of money. Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber. Let's look at an example: I'm going to build a table that will require 50 board feet of oak. If I buy finished oak it will cost around $5.5 / bf or $275. Alternatively, I can buy rough cut oak at $1.25/bf or ~$65. In this one project I've saved $210. That's enough for a new power tool.
Ordinary clip-in-place shelf brackets with slotted metal supports can hold a lot of weight. But some-times they’re unstable and can be easily knocked loose. The play in the slots allows the bracket and shelf to shift from side to side. To prevent this, use your circular saw to cut 1/8-in. deep slots into the undersides of the shelves, aligned with each bracket. When the shelf is assembled, the brackets fit into the slots, eliminating the sway. Also check out: How To Build Floating Shelves.
I used to keep screws in a cof- fee can, but when I reached in with my hand, the screw points pricked my fingers. The can was also a dust and dirt depot. I bought a clear water bottle with a pop-up lid and poured screws into the bottle with a funnel. The screws stay clean, and I can shake them out of the bottle one at a time. — Bruce Burley. Hardware Storage: DIY Tips and Hints
Often times those same freedom-seeking, passion-driven individuals that started their journey filled with courage and optimism, become some of the most time-pressed and financially-stressed people out there. The flip side of getting to create your own wealth is that you are solely responsible for creating your own wealth. That’s right, it all comes down to Y-O-U.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette package. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provincial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effectively through your drawings that your structure will comply with the technical requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior finishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electrical and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.
Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for billing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.
A very simple countertop but one that should work great for our workshop, now we’ve already applied one coat of polyurethane to kind of seal up the plywood. Now we’ll be applying another coat once that dries to give it a little bit of durability because this thing will get a lot of abuse. Now Tim’s applying the same kind of clear sealer to our little rolling workbenches here, and I think this is a great idea, we’ll be able to roll these out, lock down the casters on the bottom then you can have a drill press or any other bench top tool that you can work on, then when you’re finished with them you can roll it right back, tuck them up against this wall and it serves as a good storage unit and gives you the chance to keep the workshop wide open for some of the larger projects we might be working on.
A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
First, try to remove all the extraneous household items that don’t facilitate making stuff. In a perfect world, you wouldn’t have to dig past kids bikes or empty luggage to get to your paint supplies. In the real world though, storage is hard to come by, so you’ll have to give a little to get a little. Consider a line of demarcation in your garage to separate “household” from “workshop.” If you don’t have enough room, consider a smaller-space workbench, or rent off-site storage. You could even build a shed for more covered storage.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
We did our best to keep costs down, but there was only so much we could do. We needed the shop to go up quickly, which eliminated the prospect of me doing some of the work myself. Additionally, we live in a neighborhood with a homeowner’s association. This means we have very specific restrictions for what we can and can’t do on our property. So the shop must have all of the same finishing touches as our house.
Everything from the way the customer is greeted as they walk through the door to the way your products are presented following a sale matters. The smallest details can make the biggest difference. Early on when just starting your small business, you as an owner, will be able to exert a lot of direct control over these details. But as you grow, you will come to recognize the value of a well-trained and motivated staff.
While we were painting all of the walls in our workshop our plumber dropped by to hook up an old laundry tub sink that we’ve had for several years. Now, he hooked up to the cold water line on an outside water faucet, so we’ll only have cold water but still this will be really convenient to have this right here in this shop. Well we’re about to set our last base cabinet, and once they secure that well to the wall we can start on all of our countertops.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Smaller speed bump displays (above) and larger merchandise outposts (below) placed along your store’s main traffic flow let you draw customer interest to certain products. Speed bumps let you feature new finds and hot sellers in eye-catching ways. Larger outposts are great for special price stock or product groupings such as seasonal features and branded collections.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
In a small store, these are usually one and the same. In stores where customers don’t shop with baskets, Lesley recommends having a checkout counter large enough to hold products as customers continue shopping. Remember, empty hands pick up more products, and that leads to more sales. Also, make sure checkout counters are large enough to handle the checkout process efficiently and allow space for customers to set down a handbag.
While a single great product can’t usually support a whole business, it is beneficial to select one or two “headline” products that will form the cornerstone of your offering. This will often be an obvious choice: If you’re a coffee shop, your headline product will be coffee. If you’re a burger joint, you guessed it, it’ll be burgers. This product will often be the centerpiece of your marketing efforts and a way for you to “own” a space in a customer’s mind. For example, Jack’s Burgers makes the best cheeseburger in town and Daisy’s Threads has the most adorable scarves.
While strolling through the recent entries to our online shop gallery, I spotted some pretty novel designs as well as a couple of fun videos worth taking a look at. From brilliant solutions for tight spaces, to novel repurposing of department store display racks, there were plenty of interesting elements to the eight shops listed in my February round-up. By the way, if you’ve already seen our art director’s video tour of his redesigned garage shop (Mike’s Garage Shop), you can go ahead and skip it. If not however, it’s really worth a look!
If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”
YouTube: I love this place! You can find video training's on just about everything! It can help you with a lot of the tasks that you need to accomplish for your goal. So if you want to "sell products using Instagram" and one of the tasks is: post beautiful photos with text on my feed often, then you probably need to go on YouTube and search for "how to design an Instagram post, if you don't know the first thing about it. You can use YouTube to help you accomplish goals or tasks on your list that is out of your skill set.
So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.
Hey thanks for the great insight on a pickup camping setup! I just purchased a 2002 tundra with a 74″ bed. Picking it up in Denver in a week and driving it to Durango and then around the southwest. I mainly decided on a truck for a mobile place to keep my dog(that doesn’t have an interior he can rip to shreds), but I am thinking of building a setup similar to yours. You haven’t used yours with a canine companion have you? Any suggestions on keeping it dog-friendly, dog-comfortable and dog-proof? I will be keeping him in the back while at work and such and will be camping in the back with him and possibly another person.
As a retailer, it's possible to use furniture, displays, racks, and other tools to create a clear path for your customers through your store. This will vary greatly depending on the size and your general store layout. However, you know that most North American customers will naturally turn right — so, your next job is to make sure that as they do, they also continue walking throughout your store to gain the maximum exposure to your products. This not only increases the chances of them making a purchase, but a well-thought-out path can be a great way to strategically control the ebb and flow of foot traffic in your store.
Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.
State Parks/Developed Campgrounds. Every once in awhile, it’s kind of nice to stay at a state park or other developed campground - and a big reason why is that they have showers (and sometimes laundry, too). This is what we’ve done most often when we need a shower on the road. Many state parks also have small day use fees if you don’t want to actually camp there.
The on the go mode is ideal for when I’m just driving all day and need to pull over and get some rest, be it in a parking lot, a residential cul-de-suc, or wherever. I usually toss a couple of items in the cab of my truck and crawl into the “coffin” sleeping arrangement for a quick night’s rest, but I can also crawl in without placing anything in the cab.