Well I think I’ll have plenty of light once we get all of 24 bulbs in place. I’m really glad I saved those old fixtures. Hey another thing we’re reusing, and I’m really glad I saved, is these old cabinets that we took out of a kitchen renovation a couple of years ago. This will be perfect to serve as our base cabinets so that we can build our sturdy countertop on this side of the shop.
The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively win­dowless north walls may be a place to arrange wood storage or mechanicals.
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
My enthusiasm was kindled and I made friends with Surrey Timbers for more 'exotic' wood. My next purchases were a Drill Press and a Scroll Saw from Axminster Tools and I set to work. An excellent piece of Yew followed by some Thermal Ash has so far produced 4 cribbage boards. I then obtained a Palm Router which, after some practice, I find better for the more intricate work.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well.
I’ve been living out of my Mazda 3—not the hatchback version!— for over two years now. I love the gas savings (standard transmission; I can get up to 40mpg) and the ease of getting around places. I don’t love that I can’t lay flat (hurts the back) and that organization is tricky. However, there are certainly ways to make it work. Ryan linked to one article and there are two others that shed light on some important aspects when going on a long road trip like this.

They’re also very energy-efficient, so they won’t be a heavy load on your batteries. The best 12V fridges use highly-efficient compressors that have very low power draw (0.7 - 3.0 Amps per hour, depending on the model and the ambient temperature). They’re also well-insulated and feature top-open lids, which prevent the cold air at the bottom of the fridge from escaping when the lid is open.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
Well I was just thinking about all of the supplies I’ll be able to keep in this large shelf unit we just installed in our workshop. Hey, that’s we’re doing this week is creating a very practical realistic workshop where we’ll be doing a lot of projects for the TV show, but it’s also going to be used by my construction company so it really has to be set up properly.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Conduction is heat transferred across solid surfaces- think touching a hot stove. It’s also how heat gets out of your van in the winter. The heat inside your van is conducted through the solid surface of your walls and ceiling. Insulating the inside of your van will help prevent heat loss through conduction during the winter, and will also stop your van from conducting the sun’s heat inside during the summer.
It’s hard to overstate the importance of choosing the right location when starting your small business. We’re sure you’ve heard the saying 1,000 times before, Location, Location, Location! Some of the world’s most well-financed franchises have this weaved into their business DNA. McDonald’s Ray Kroc is the perfect example. When asked about the business, this well-know American businessman and philanthropist once stated, “We are in the real estate business, not the hamburger business.”
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us.
Well, my workshop is finally complete and I’m ready to take on just about project that comes down the line. And I’m pretty well set up here. I’ve got a great workbench, plenty of table space over here that easily rolls around the shop if I need it, lot of storage space down here, I can tuck these tools away or bring out any new ones that I need. And as you can see I’ve got plenty of supplies to tackle just about any project.
Then there are material considerations, such as how to bring full-size sheets of plywood home to cut down to size (you don't). And safety and cleanup are two more concerns: Proper ventilation and dust collection, a cinch in a larger shop, can be quite a challenge (and a potential health hazard). Nevertheless, you can set up a great wood shop in a small space, and we'll show you what you need.
If you dream of devoting your life to a cause you believe in, it might be time to start a nonprofit. You’ll need to incorporate your business and file for 501(c)(3) tax-exempt status -- and then you’ll be required to meet ongoing standards of compliance, but the payoff is making a meaningful impact on a cause you believe in. Want to do good while still making a profit? Consider social entrepreneurship.
Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
While a single great product can’t usually support a whole business, it is beneficial to select one or two “headline” products that will form the cornerstone of your offering. This will often be an obvious choice: If you’re a coffee shop, your headline product will be coffee. If you’re a burger joint, you guessed it, it’ll be burgers. This product will often be the centerpiece of your marketing efforts and a way for you to “own” a space in a customer’s mind. For example, Jack’s Burgers makes the best cheeseburger in town and Daisy’s Threads has the most adorable scarves.
Equity financing is money raised in exchange for a share of ownership in your business. The core benefit of this type of funding is the lack of debt. You won’t have to worry about those pesky monthly repayments. The downside? You are giving up total ownership of your business, you are giving up the rights to a portion of the ongoing profits of the business, and you are potentially giving up some control of how your business is run (Though this is not always the case).
To help, it’s important to determine the average price per square foot for your area. Price per square foot is typically derived from the annual lease amount divided by the total rentable square feet of the space. You can find the average price for your area by typing your zip code into LoopNet’s directory of commercial properties available for lease.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.

Can you outfit your shop with all the necessary hand tools for just $100? Christopher Schwarz says you can, and he’ll show you how to do it in this article. Take Christopher’s shopping list to the flea market and come back with everything you need for less than you’d spend on one new hand plane. You can do all your woodworking with hand tools, and this article from Popular Woodworking will equip you with everything you need.
Before you bid in an online auction, check the site’s rules of operation. At some sites, a winning bid is a binding contract, which can be a problem if you can’t inspect the tool before you purchase it. Don’t forget shipping costs. In some cases they can exceed the cost of the tool. Also, make sure the tool you’re buying will run on the power you have in your shop. Many former industrial tools run on 240v single-phase power. If your shop doesn’t have 240v service, you’ll need to factor in the cost of upgrading before deciding to buy. You don’t want to saddle yourself with a tool you can’t use, no matter how good the price.

Well, we’ve managed to put together the workshop I’ve always wanted. One that’s practical, functional and neat, well at least for the moment. We have plenty of light, plenty of power, lots of work surfaces and enough cabinets, shelves and hangers to organize all of the tools we’ll be using here. I’ve even managed to do a little creative workshop decorating along the way to remind me of how I got started in this business in the first place.

I have to agree with these folks....I have a two car garage/workshop that needs to double for ski waxing, bicycle storage and house repairs. I have a Hybrid Table saw, 6" jointer, 13" planer, a shopsmith that serves as drill press, lathe and band saw, dust collector, two work benches...and everything has been designed to roll away, under, above something else...I can set up and tear down in about ten minutes, because at the end of the day, I always have to park two cars in the garage. Always great to look at the great dream workshops, but thought that they should do an article on guys like us, that have to fit several hobbies into one spot. I seem to spend a lot of time planning, and re planning the garage space to try and fit the next tool. I dream about the day I will get a place that I can dedicate to my tools, but until then, I just buy things with wheels.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
Find out what tools you need and how to budget for shop setup. Whether you are going to be doing furniture, cabinetry or woodturning, this workshop tools list and budgeting guide can help. Learn how to prioritize purchases of shop tools based on space, interests and cost. Check out a comparison of the workshop tools you can get for $4000 vs. $10,000 and determine how much you need to spend for the shop you want.
​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.

If you dream of devoting your life to a cause you believe in, it might be time to start a nonprofit. You’ll need to incorporate your business and file for 501(c)(3) tax-exempt status -- and then you’ll be required to meet ongoing standards of compliance, but the payoff is making a meaningful impact on a cause you believe in. Want to do good while still making a profit? Consider social entrepreneurship.


Without organization, living in a van can feel cluttered and chaotic, so you'll want to make the most of your storage space. This is a good time to make sure you've paired down your belongings to a reasonable amount and to make sure everything has a place. (As a former engineer who loves making things as efficient and optimized as possible, this was Ben's favorite step!) 
All this is why I recommend you buy the very best stuff available, even if it means going without certain tools initially. Although it wouldn’t be a disaster to spend $1000 on a whole bunch of inexpensive tools, what are you going to do when you’ve outgrown the capability of these tools and want to upgrade? You’ve now got to somehow get rid of the cheap stuff and replace it with something better. This isn’t easy and it’s always the most expensive way to go.
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
Hey Brett! Awesome to hear that your own plans are coming together. I can’t really recall seeing any dirtbags rolling around in a Pruis… I wouldn’t imagine it to be the ideal vehicle for transporting gear and living out of, but the gas savings would really add up over 6-7 months on the road. In general, I’m in favor of going with what you’ve got and finding creative ways to make it work. Maybe you can add a rooftop box? On some vehicles, people even remove the passenger seat(s) for extra storage space. The biggest problem with the Prius that I see would be finding a place to sleep while you are on the road… But I guess that’s where your gas savings and cheap hotel would come in. I know Gina Begin has been living in her little car for a long while now, check out her stuff, and maybe reach out to her. She’s a veteran at dirtbaggin’ it in a car: http://www.ginabegin.com/2013/05/the-ultimate-guide-to-living-on-road-15.html
I have a plastic bed lining on my truck, which also covered the back of the tailgate… I just popped the screws off, took off the plastic liner and drilled holes in the sheet of plywood to match those used by the plastic tailgate cover. Sorry if that doesn’t help you with your setup. But I’m sure you could just drill your own holes in the metal tailgate. Use the plywood cover as a guide for your screw holes…

I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
Time spent earnestly involved in the creation of something designed and made with one’s own ingenuity can be quite enjoyable. So now when I don’t feel motivated to do more practical things I often turn to an idea about some device or other that I’ve wanted to try making but never got around to. Ultimate Small Shop Videos I can recall many such improvised devices that gave me satisfaction and enjoyment.Ideas for things to make come from many places. Most often the idea comes from some need. I do a lot of keying of text using a computer keyboard. I tend to keep the room temperature a bit cool, cool enough that my hands become uncomfortable. I ended up rigging a length of electrical heating tape wound in a large coil-shape to surround the keyboard. Tying the heat tape to a large piece of cardboard keeps it in place. It does a nice job of keeping my hands warm. I can leave the room temperature set where I want it. As far as I know, you can’t buy anything like that. Building and inventing improve my understanding of mechanical devices and materials. It gets easier to manipulate and modify the physical things that are so much a part of everyday living. With effort and imagination, often new devices can be made or existing ones improved for my enjoyment and satisfaction. Both intuition and logic are used to make a homemade gizmo. The more the two abilities are used together, the more powerful the combination becomes. A strong partnership of reason and creativity helps a person to produce and enjoy life. It is fun and satisfying to conjure up and build simple devices. Those created items command more appreciation than more casually acquired, purchased items. And it feels good proving that imagination and ingenuity can make life better. The process of invention seems magical. The mind pieces together what it has already made some sense of into something new. It seems that even the most obscure result can eventually be produced. The grass hut and the keyboard heater each gave me a little taste of that magic. Until recently crafts were usually sold locally or, at best, regionally. Now you literally have the whole world at your fingertips! Some of you may choose a gradual progression from selling to friends to selling at fairs and shows, to retail selling … and so on. Others may decide to jump directly from selling within their circle of friends to the worldwide Internet market – the costs are low enough that this is surprisingly doable. My first career was as a special education teacher. After 15 years of teaching, I earned an MBA degree followed by CFA (Certified Financial Analyst) certification. Ultimate Small Shop Pdf Download After 15 years in finance I was a vice-president and portfolio manager of a major insurance company before I was downsized.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
There are a variety of structures to choose from when starting a small business. However, the most common business structures include sole proprietorship, partnership, corporation, and S corporation. The structure you choose determines which income tax return form you have to file, which, you guessed it, dictates your legal and financial responsibilities as a small business owner. Because of this, you’ll want to make sure you understand the options that are available to you and weigh the pros and cons before incorporating your business.
We're living in an age where we can order groceries, turn on the lights in our house, or get in a workout from the convenience of our phones, tablets, or other devices. Apps are a part of our everyday lives. They are increasingly giving us more free time or vying for more of our attention, depending on how we choose to use them. With that, here are some of the more important changes since we published our app cost article in 2015.
Many retail fixture and display companies provide store planning and design services to their customers. Though typically not free, these in-house design services can be far less expensive than hiring an independent designer. Plus, they can help streamline the process of store layout and planning, along with the purchasing and installation of displays and fixtures.
So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
I used your set-up as a guide in building mine. It is a little different – it’s shorter a little bit, as I have a shorter canopy cover and I didn’t make the sleeping platform flush with the walls of the truck bed – but it turned out great! I’m really happy with it. Also, one of my favorite parts about it is none of it is actually attached to the truck. So I can take everything out and it makes cleaning a little easier. I’d post photos if I knew how. If you feel like seeing it let me know and tell me how to get them to you!
Remember, your retail store layout guides product placement, directs customer flow, and defines the overall look and feel of your store, so it deserves plenty of thought. Many factors will affect your floor plan choice, including the size and shape of your sales floor, the types of products you sell, and even the customers you hope to attract. Keep these factors in mind as we explore each floor plan option in detail.
I don’t think you have run into this problem, but I have to deal with condensation in the cap as I live in a moist climate. I was thinking of an old van type roof vent with fan for active ventilation, or drilling holes along the side of the cap, inserting short cuts of pipe with fine screens (mozie land), and capping them. This way I could control for rain, cold, etc., but create some passive cross ventilation at roof level.

Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.

I think the music comment was about speakers for playing music. I put a few 8″ in ceiling speakers in from MonoPrice.com ($60 / pair I think) and love them. A space that big would probably need at least 3 pairs. You’re not throwing a rock concert with them, but they provide very decent background music for not much cash. The speaker wire from MonoPrice is dirt cheap too. Just add a cheap receiver to drive them. Of course, you probably don’t want to spend that cash at the moment. But it’s a good starting point for the future.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
A very simple countertop but one that should work great for our workshop, now we’ve already applied one coat of polyurethane to kind of seal up the plywood. Now we’ll be applying another coat once that dries to give it a little bit of durability because this thing will get a lot of abuse. Now Tim’s applying the same kind of clear sealer to our little rolling workbenches here, and I think this is a great idea, we’ll be able to roll these out, lock down the casters on the bottom then you can have a drill press or any other bench top tool that you can work on, then when you’re finished with them you can roll it right back, tuck them up against this wall and it serves as a good storage unit and gives you the chance to keep the workshop wide open for some of the larger projects we might be working on.

The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​
Many small businesses in New York and New Jersey were forced to close following Superstorm Sandy because they lacked the insurance that would have gotten them back on their feet. That part is well known. What’s less well known is that this lack of proper insurance, coupled with the lack proper legal incorporation, resulted in many entrepreneurs seeing their personal assets come under threat.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

Since there’s less wiring involved, installing LED strip lights is much simpler than puck lights. You also won’t need to cut any holes because strip lighting should come with its own adhesive. We’ve seen most vanlifers stick strip lighting down the side edges of their ceilings. However, it’s not as easy to create separate lighting zones as it is with puck lights.


You may not have heard of Lemonade Freedom. It’s an organization set up after a spate of children’s lemonade stand closures by police who decided to take an absurdly heavy-handed approach to permit enforcement (you can read more about it in Forbes). Apparently the kids involved hadn’t applied for the necessary paperwork to run their stands. In one example in Georgia, three kids saving for a trip to their local water park had their endeavor closed down because they lacked the business license, peddler's permit, and food handler's license. Crazy? Only mostly.
If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”
I totaly get not wanting to get into the cost part of the shop. We just went through a house renovation, and my stock answer to the ‘how much’ question is either ‘enough’, or ‘enough that was right for us’. There is a quality of life or utility aspect that every person needs to figure out for themselves. And, I would think not having to bounce around from garage to garage anymore has gotta be worth something!
The small apparel boutique pictured above really nails these traffic flow details! A roomy entrance offers clear sight and travel lines to eye-catching power walls on the right, and an inviting seating area towards the back. These lure customers into the store with the promise of treasures and comfort within. The shop even has a left-side checkout midway back. Someone really did their customer behavior homework on this retail store layout.
Some people lean towards starting a small business because they seek freedom, others to fulfill their passions. Some entrepreneurs, however, are driven by a desire to build a legacy, one that that they can hand down to generations to come. Whatever your reasons are for reaching for the stars and aiming for the moon, before you start, remember, there is a dark side.
The good news is this: You are not a statistic. Think about this — if it was reported that small business owners over the age of 50 were more likely to succeed, would you wait until you were 50 to start a small business? Not likely. You would start when you felt ready. And that’s the point — only YOU can know when it’s time to take the plunge. Likewise, only you can make the intelligent decisions that ultimately mean the difference between success and failure when it comes to launching your business.
Before starting your small business and opening its doors, it is important to take some time to define your end goal. While it almost goes without saying that this goal will be subject to change, it is only by recognizing and clearly articulating your long-term ambitions that you can provide yourself with a compass that will guide every business decision.

Hi thanks for the info. I’ve got a 2009 tacoma and went with a simple, no screws elevated system. I’ve also got a mx series ARE shell with rack rails so I’ll probably take too much stuff now. Oh well. My question is: how did you attach the plywood to the life gate? My carpentry/construction skills are best illustrated by the “Homer Simpson spice rack”. You used the existing holes in the tail gate, but did you put the tail gate cover back on the tail gate and put the plywood over it and screw thru both or ditch the cover? Thanks
Both of those broader lenses are still useful ways to look at app costs, but costs can additionally be broken down by app type and the features associated with them. Also, two years in technology is a very long time. So, we will start by looking at what's changed. We'll then move on to looking at app costs based on the different kinds of apps in the market.
According to store design experts, this is the part of the process where store owners tend to put the cart before the horse. Once the floor plan is sketched out, store owners are quick to purchase and install fixtures, then fill them with product. Far too often, the fixtures chosen aren’t ideal for displaying a range of products in a particular space. Or worse, they don’t offer flexibility needed in valuable display areas that are constantly changing to house featured and seasonal products.
I bought an energy-saving outlet strip for my TV and its components. One outlet controls several other outlets on the strip, so when I turn off my TV, the adjacent controlled outlets for my VCR, DVD player and receiver sense that no current is going to the TV anymore, and those outlets shut off. Then I decided to try it out in the shop. I use it with my router table, disc sander and orbital sanders, so when I flip one of them on, my shop vacuum also starts up to take care of dust collection. It also has two outlets that are independent for other accessories you’d like on all the time. You can buy the outlet strips at amazon.com. One choice is the Belkin Conserve Socket with Energy Saving Outlet (about $30). — D. Linley. Plus: 30 more smart tips for working in your home shop.
Often times those same freedom-seeking, passion-driven individuals that started their journey filled with courage and optimism, become some of the most time-pressed and financially-stressed people out there. The flip side of getting to create your own wealth is that you are solely responsible for creating your own wealth. That’s right, it all comes down to Y-O-U.
It’s tempting to place new products, hot items, and sale signage front-and-center so they’re the first things customers see upon entering. But don’t do this! The first few feet inside the door, say five feet for a small store, and 15 feet for a larger store, is known as the decompression zone. Store design experts strongly advise against cluttering up this space.
Our practical workshop is coming along nicely. We’ve created a big open space and added plenty of electrical power and lots of light. We’ve also added some great storage capacity using recycled kitchen cabinets and some old shelves. Now, with our tool compartment and work surfaces in place we’re getting very, very close, but I wanted to get a little input on the final details from some other folks who spent a lot of time making sawdust, so I asked my co-host Allen Lyle and our website editor Ben Erickson to look around and give us some of their ideas.
This is about how I built my wood shop. We decided to move from our previous home for a variety of reasons. I saw the move as an opportunity to gain a bigger shop for my wood working hobby. The house we found had everything we wanted, except for a shop or even a garage. It did have a non functioning indoor pool. We thought this space would make a nice wood shop. I could just build a floor over the pool and have a shop. As we got further into the inspection process, it was looking as though fixing the structure over the pool was going to be expensive. It looked like we would have to put a bunch of money into a structure that was not really a wood shop and not a functioning pool either. It made more sense to take out the pool and structure, and then build a wood shop from the ground up. We started this project by regrading our side yard to gain access to the pool in the backyard. Once we had access, we took out the pool. We half filled the hole where the pool was with compacted gravel. I realized that if we sank the shop into the ground I could have the ceiling height I had always wanted in the shop and preserve the view from the house. The design of the shop is a box with a shed roof. The roof wraps down the east side of the structure. I like to think of it as a slightly open toolbox. The entire shop is laid out on a 24 inch grid. The windows and doors fall within this grid. I had a general contractor built the shell and then I built the windows and interior. The interior walls are comprised of a 34 inch concrete stem wall at the base. Above that is a 9 foot, plywood wall. In the space above the plywood wall and below the shed roof is poly carbonate panel to form a clerestory. The tool layout in the shop is divided into 4 areas: an area near the door for material storage and prep, a central area for general wood working, and two areas near the back of the shop, one for turning and one for metal working.
James Hamilton (or “Stumpy Nubs”) is a self-taught tool expert, engineer, writer, teacher and video producer. In 2008 he went into woodworking full time, creating a weekly Internet woodworking show that focused on the workshop itself. Now, Stumpy Nubs Woodworking has grown into one of the most popular multi-media woodworking resources in the industry.
I have a question, you mention what a problem it would be if the cinder blocks were to sink yet you have installed them with the least amount of footprint on the ground. Was there a reason for this? I would have installed them with the flat side on the ground, and I realize they would not hold as much load as the way you have them but considering the number you have used, the spacing, and the size of the shed, load should not be a problem. Just wondering.
Compensation is a critical key to retaining and motivating the right employees. However, since small businesses often start out with tight budgets, compensation is an area they often struggle with, commonly leading to bad hiring decisions that affect overall business performance. The good news is that employers willing to step outside the hourly-wage box have a variety of options.
Ultimate Small Shop is a complete guide to setting up your own workshop, from the planning phase to optimizing it for business. You’ll learn how to put together a complete and functional workshop for less than you expect. Ralph aims to get your shop set up for less than $1,000. Ultimate small Shop includes suggestions on where you can get the tools and equipment needed at the most affordable prices and how to optimize space to get the most out of the little room you have.
Congratulations on your new shop and all your success. I’ve watched all of your videos and someday if I have the money I would love to join your guild. I started a small workshop in my grandparents basement and someday I hope to start a small bussiness. Your website and videos have been the most informative and the most inspirational to me as a beginning woodworker. Thank you for sharing all your tips and hard work with people like me. I look forward to watching your videos for years to come.
In many ways, skoolies are the ultimate in mobile living. The big advantage here is space - there’s tons of room for couches, beds - even a full bathroom - and you can easily accommodate families and other larger groups. There are also some really impressive skoolie builds out there that are nicer than actual houses, and it’s a whole lot cheaper to convert a bus than to buy a similar-sized RV. Skoolies come in multiple sizes, from “shorties” to full-sized buses.
There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior fin­ishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electri­cal and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.

This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Overall I am very happy with the final results and I can’t wait to get back to making sawdust. The first project to be completed in the new shop is going to be a Queen Size Platform Bed for one of my favorite clients. I mentioned in a previous post that one of my goals this year was to get back into doing client work and this is me making good on that promise. I can’t wait to get started!
If you want the ultimate vehicle to customize for your DIY van conversion, the Sprinter is the van for you. They have enough headroom even for tall people to stand up, and enough interior space to design any kind of layout. They also typically have diesel engines, which means greater fuel efficiency and engine life (many diesel Sprinters have been known to make it past 400,000 miles). If you think you’ll be doing a lot of off-roading, the Mercedes Sprinter also comes in a 4x4 version.
Becoming a small business owner is one of the most rewarding and inspiring journeys a human being can take. It provides you with a chance to be your own boss, take control of your financial destiny, and become a meaningful contributor to your local economy and community. There will always be a reason not to take the plunge. But if there is one rule of small business — and life — is that nothing will happen if you don’t make it happen.
The right first step online for most stores and restaurants is creating a Google Local Business Listing. Google accounts for 90% of all global organic search traffic and more and more of that traffic is coming from mobile devices. Chances are, your customers are using Google to find you, so you’ll want to make sure your hours, description, contact details, address, and images are all accurate.

One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.


The issue with the old shop was manufacturing capacity and layout. We get runs of 4 to 6 of the frames on the left in the last pic and sometimes frames twice that size. We were masters of having everything on wheels, which works for a while but it takes twice as long to build anything that way. Then the office ladies walk through the shop to the kitchen while you are grinding and complain about all the dust etc.
Ryan, I have the same (almost) 90’s Toyota Pickup and love it! this is so helpful, and I will definitely be using this method. my main concern is that 1/2′ plywood sagging. do you notice it sags quite a bit or does it mostly hold up? my thought was to build the vertical bins a little wider, so that the plywood bed platform wouldn’t be under so much stress. the second issue im running into is wrapping my head around trying to organize and compartmentalize things appropriately. what do you typically put where so it is easy to reach and use?
If you’ve been to gem shows, you know how overwhelming and daunting they can be. Although it’s difficult to narrow down all those tempting options, your jewelry business profit margin will be greater if you plan ahead and focus on shopping for a particular line and color scheme of jewelry. Ultimate Small Shop Online Review You must keep the bigger picture in mind and try to keep your emotions out of the design process. Here are some tips for defining your market and researching it so that you can walk in and out of a gemstone show feeling confident in the business investments you’ve just made. Gemstone shows and fairs are marketplaces for vendors of gemstones, findings, jewelry supplies, and tools. Due to a large amount of competition between the vendors, prices tend to be competitive. I’ve found unbelievable deals on high-quality gemstones and findings at gem shows. To find gem shows near you, you can simply do a Google search for “gemstone show” or “gem fair”. Other sources of information are your local convention and visitors’ bureau and any lapidary clubs in your area. Anyone can attend most gemstone shows. Although you don’t usually need a wholesale license to get in, some vendors may ask for your resale permit before letting you buy at wholesale prices. Show admission fees tend to be in the $5 to $10 dollar range. What market are you trying to target with your jewelry? Don’t try to please everyone. Ultimate Small Shop does it really work Are you trying to appeal to individuals like yourself? What age bracket are you trying to reach? Does your jewelry line appeal to funky or traditional individuals? Next, take a trip to your local department store and take note of the colors that are being used for the upcoming season. Look at the jewelry and observe the lengths of the earrings/necklaces, the sizes of the stones, and the other various style elements for the season. While your designs should not be copies or replicas of the jewelry in the stores, you can simply incorporate the observations you make into your own original design ideas. Fashion and jewelry magazines are also a great place to find out what trends are coming into the stores. There will be an overwhelming array of gemstones and supplies at the show. Having a jewelry line style and color scheme in mind will allow you to narrow your focus. Vendors will offer gemstones in more shapes, sizes, cuts, and colors than you can imagine. Stick to the colors you’ve mapped out for yourself and walk through the entire gem show once before buying anything. Jot down and compare the prices of items that you’re interested in. Then take a break, go outside for some fresh air, and reflect on the items you saw and really liked. Then review your budget and the jewelry line you have in mind before returning into the gemstone show. Ultimate Small Shop Guide Download This will help you get the best deals on the items you’re most interested in so that you don’t blow your budget or become overwhelmed by the options. Soaring through the air, watching the clouds and the birds fly by.
Many DIY campervans have kitchen units that are directly behind the cab, sealing it off from the rest of the van. These layouts offer increased privacy and stealthiness, especially if you completely wall off the cab, and open up some space in the back of the van. This layout can be paired with a lengthwise bed, fixed bed, or convertible dinette bed. You can also place your propane and water connections right by the door, making refill easier.
We all know that we’re not supposed to judge a book by its cover. The truth is however, that it’s human nature to judge based on appearance. Though most of the time, despite our good intentions, it happens unconsciously. As consumers we make incredibly quick decisions about the businesses we choose or choose not to frequent. As we enter a location we take in the signage, the windows, and the product displays. And with the blink of an eye we determine a dozen different factors. Is this location trustworthy, clean, and friendly? Is the staff likely to treat me well? Will the products be to my liking? Will I find what I need and complete my purchase quickly? Can I even afford to shop here? And, perhaps most importantly: Is there something unique about this place?

While not as large as I would have liked (is a wood shop ever big enough?), it is about twice the size of my previous shop. It measures about 12 by 25. Fortunately I had managed to find quite a bit of shelving before the move, so I was able to install shelving along two walls. And the work benches were made from wood salvaged from packing crates from Europe and left over yellow pine car siding and flooring from remodeling the old house.

Making sure any holes in your insulation are sealed off and filled helps your insulation really do its job. Great Stuff Gaps and Cracks spray foam insulation is the best way to fill in any space around your foam boards, and to insulate any hard-to-reach spots. You can also spray this into the hollow vehicle frame for insulation (you’ll need a whole bunch of cans for this).

Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back.
×