Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.

I framed and sheathed each wall individually and then stood them up with the help of long 2x4 braces.  My neighbor let me borrow his framing nailer, which made things go much faster.  I added a second cap of 2x4 on the top to make the walls a little more rigid.  I then laminated 4 2x4's to construct a ridgeboard.  I nailed in some temporary 2x4 supports and had a friend help lift it into final position.  Once all of the rafters are cut and nailed into place, the supports were removed.
I hope to build my own stand-alone dream shop sometime in 2015 – in the Texas Hill Country. I’ve not yet found the right lot, so much is yet unknown….but am thinking roughly 30′ x 40′ overall, with 10 or 12 foot ceiling. At one end, there will be a 10′ x 30′ space walled off into three spaces: a small finishing room, an office/design space, and a half bath.
This sturdy 30-in. x 6-ft.-long DIY workbench is the ultimate in simplicity. It’s made from only fifteen 8-ft.-long 2x4s and one sheet of 1/2-in. plywood. Learn how to build a workbench by following the cutting diagrams to cut the parts: Figure B to cut the plywood tops, then Figure C to cut all the framing. Use the lengths provided in the Cutting List (see Additional Information below). You can either screw the framing together with 3-in. screws or hand- or power-nail it together with 3-in. nails. Screw the plywood down with 1-5/8-in. screws.
These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.

Budget Toilet: Luggable Loo. With the Luggable Loo from Reliance Products, you can turn any 5-gallon bucket into a portable toilet for your van. Make sure to line your bucket with a trash bag or toilet waste bag - then once you’ve done your “doodie” just tie up the bag and dump it in the trash. Reliance also sells deodorant chemicals that will make it easier to live with your new roommate

Even if a website and social media aren’t part of your immediate plans for launching a business, as a savvy 21st century entrepreneur, you want to make sure that you have complete ownership of your brand identity before paying any fees required to register your business. Using the example of The Sunny Rabbit, at the very least, you would want to run an online search to ensure that TheSunnyRabbit.com is available. Assuming you want to join the other 50 million small businesses marketing to customers on Facebook, you’ll also want to make sure that Facebook.com/TheSunnyRabbit is also available.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
Have a walk-through yourself and see where the visual cues guide you or get your staff, friends, or family to do the same and give you honest feedback. Don't forget to observe your customers and see what they're drawn to, what they avoid, and how they move, then match that with your intended design. If you keep resilient and keep your eyes and ears open, you'll be sure to create a retail design that's a win-win for both you and your customers. 
Woodworking isn’t just an overnight hobby, for most it’s a fun pursuit that lasts a lifetime. As your skills develop, the workshop becomes a place not just to build but to repair along the way. In a world where people are strongly influenced by consumerism, there’s a tendency to revert to a throwaway culture. But if you can fix before throwing away, then your tools start to make a return on their investment and have a bigger impact.
Just stumbled across your article and it’s right on time as I am about to launch a special events venue (ballrooms, meeting rooms, outside garden area, outsourced caterer, etc). Not sure what type of zoning this business falls under. I read that zones are usually for office, retail, industrial and leisure. Any idea what type of zone I should be looking for? Also first time trying to get a commercial space for this type of business, any specific suggestions?
​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool. 

7. Illuminate your space in different ways. Lighting is important in any retail shop, but it's particularly critical in tight quarters. If a corner of your store is not well lit, that square footage is as good as lost, Langdon says. She recommends using a combination of track lights, lamps, sconces and picture lights. This mixture will not only ensure that your entire space is well lit, but it also will add flair and variety. "Picture lights are amazing. They give a wonderful glow," she says. "Think in terms of layers of light."
We’ve been focused on the first category so far, but there is also an allure to buying an existing business. These enterprises will often come with brand awareness, a customer base, trained employees, an established supply chain, and most importantly (we hope), demonstrated profitability. As a result, countless startup risks can be diminished by taking this route. That is only true, however, if you make sure to carry out thorough due diligence on the existing business.
Overall I am very happy with the final results and I can’t wait to get back to making sawdust. The first project to be completed in the new shop is going to be a Queen Size Platform Bed for one of my favorite clients. I mentioned in a previous post that one of my goals this year was to get back into doing client work and this is me making good on that promise. I can’t wait to get started!
2. Create window-like effects. Windows can open up a small space and make it seem larger. At Poppyseeds, a vintage decor and fashion accessory shop in Stanwood, Wash., the owners cut window spaces into the walls separating two small rooms to create a more airy feel. In another room, co-owner Marybeth Sande put white linen panels across an entire wall, creating the illusion of windows. Hanging drapes around tall, skinny mirrors is another way to create a window effect, Langdon says. "That gives an illusion of more light and movement in a small space."
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern. 

You are also obliged to file a quarterly tax return which must detail, amongst other things, your employee pay and withholdings. Once again, failure to do this can result in, you guessed it, a fine! As you can see, it’s important to be up to speed on the rules and regulations around taking on employees, including, of course, provisions around hiring foreign workers. The good news is that there are a number of affordable payroll software providers that automate this process very effectively.

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
I totaly get not wanting to get into the cost part of the shop. We just went through a house renovation, and my stock answer to the ‘how much’ question is either ‘enough’, or ‘enough that was right for us’. There is a quality of life or utility aspect that every person needs to figure out for themselves. And, I would think not having to bounce around from garage to garage anymore has gotta be worth something!
Skoolies do have significant drawbacks, however. Their size makes them a bit unwieldy to drive, and getting to some of the more out-of-the-way camping spots just won’t be an option. If something goes wrong mechanically, it can be much more expensive to fix than a normal vehicle. Also, the sheer size of these vehicles means the gas mileage is much worse than other options.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
Sprinter vans have been around for awhile, but they’re still the new kid on the block. These vans are especially known for their interior height, long wheelbase, and boxier shape - making them ideal for building out a spacious, functional living space. This category includes the original Mercedes/Dodge Sprinters, as well as Ford Transits and Dodge Promasters (check out this article and this helpful graphic for more information on the differences between these).
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
Best-selling products should be placed in Primary Zones located toward the rear of the store, ensuring that shoppers will pass by Secondary Zones featuring other merchandise, increasing their exposure and sales potential (it’s why milk is always in the back of the grocery store!). You can also feature several ‘best sellers’ in window displays for exposure.”
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.

The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
Ever wonder why you walk into a supermarket and the first thing you see is fruits and vegetables rather than toilet cleaner? The complex art of displaying arrangement and the perfectly optimized in-store customer journey can seem like some sort of semi-magical, commercial Feng-Shui. But it’s actually just business 101. At its core, store design is a fairly simple exercise. Think about your shop’s layout from a customer point of view and consider what might surprise and delight you, what might annoy you, and most importantly, what might convince you to make a purchase.
Does it motivate you? This is a tricky one because sometimes we have to do the work that we don't want to do to become successful. On the other hand, if it doesn't motivate you, you just literally wasted your time writing it down because you wont complete it. Consider your skill set and desire to want to work on that goal to help you eliminate goals (because you can't do everything). 

I like how you thought out the lighting for you shop. I have 6ea.6 tube T-8s but find 6500K bulbs but find lighting for filming is not that good, seems dark to me I use a Canon T3i its a decent camera I do have a row of windows in a 16′ garage door and aman door with a window on one end and a small window at the other end of my shop. Any idea what the issue may be?Could I still be getting too much light?
I’m picking up a 4×4 Extra cab pick up tomorrow and selling my current 97 Tacoma. It’s older and it’s got a lot of miles but it still has a lot left to go. Mine is available in the 3 grand range. They’re hard to find and all the rust free trucks are out here in the west but mine is one example of many good Tacos that are available at an affordable price that will fit the bill perfectly.

This is a great project if you carefully consider your needs first. I left out the vise and tracks, but had no problem hand picking good 2x4 stock at the big box stores. I did use maple on the top sides in case I ever decided to add tracks, but it was not a budget buster by any means. The cabinet and drawers were a first for me and a great learning experience. I also added retractable casters so I can easily move the workbench around my shop. Love the workbench!
×