After starting your small business, you may eventually want to hire employees. When this happens, you are legally required to purchase workers’ compensation insurance, unemployment insurance, and — depending on your business location — disability insurance. Current states where disability insurance is a legal requirement include: California, Hawaii, New Jersey, New York, and Rhode Island.
Well, I thought about that I don’t want all that dust to kind of infiltrate everything else in the building. So actually instead of putting in some kind of dust collection system, I thought that I would probably just put a nice shop vac here. And then I have room that I can bring some hose back behind this column and then you know if you’re sitting here working on something we can have adapters that go right into a miter saw or right into a sander or have a little outlet more or less to lay up on the counter that would collect all of the dust. And the same thing could happen on any of the work we do out here.
In today’s competitive business landscape, the key card that small business owners hold up their sleeve is their ability to offer something distinctive, original, and personal. As small businesses grow, however, it can become increasingly difficult for the time-pressed, financially strapped entrepreneur to maintain direct oversight over every aspect of their store.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
First, as most eager but hesitant potential hobbyists realize, you have to be much more thoughtful about tool selection. A 14-inch band saw? In your dreams. In a small space, you're going to have to rely on bench-top or handheld tools. (It is possible to forgo power tools entirely in favor of hand tools, but that's a discussion better left for another time.)
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
In our opinion, having one of these is an absolute must for living on the road - especially in humid areas. To fully cover the width of a van’s side doors/back doors, you’ll need a larger screen that’s designed for French doors. If your vehicle has a smaller door opening like an RV, a screen meant for a standard door will work fine. We could only find standard door screens, so we bought two and hot-glued them together to cover up our side door.
“If it’s a retail space then location is critical. Proximity to other retailers, access to transportation, and visibility/signage opportunity can be critical. In this case, there may only be 4 or 5 spaces available that meet the business’s criteria and objectives. A good broker will sometimes develop creative alternatives that might be outside the locational parameters but offer other advantages – such as co-tenancy or lease term flexibility.
Now I want you to create a spreadsheet or use my worksheets and write one major goal on the top. This can be the first goal you want to accomplish. Then I want you to list all the tasks you need to do (or someone on your team has to do) in order to accomplish this task. For example; let’s go going back to the goal of "Launching a New Website". The tasks you will need to do to get this goal accomplished are the following;

If you’ve been to gem shows, you know how overwhelming and daunting they can be. Although it’s difficult to narrow down all those tempting options, your jewelry business profit margin will be greater if you plan ahead and focus on shopping for a particular line and color scheme of jewelry. Ultimate Small Shop Online Review You must keep the bigger picture in mind and try to keep your emotions out of the design process. Here are some tips for defining your market and researching it so that you can walk in and out of a gemstone show feeling confident in the business investments you’ve just made. Gemstone shows and fairs are marketplaces for vendors of gemstones, findings, jewelry supplies, and tools. Due to a large amount of competition between the vendors, prices tend to be competitive. I’ve found unbelievable deals on high-quality gemstones and findings at gem shows. To find gem shows near you, you can simply do a Google search for “gemstone show” or “gem fair”. Other sources of information are your local convention and visitors’ bureau and any lapidary clubs in your area. Anyone can attend most gemstone shows. Although you don’t usually need a wholesale license to get in, some vendors may ask for your resale permit before letting you buy at wholesale prices. Show admission fees tend to be in the $5 to $10 dollar range. What market are you trying to target with your jewelry? Don’t try to please everyone. Ultimate Small Shop does it really work Are you trying to appeal to individuals like yourself? What age bracket are you trying to reach? Does your jewelry line appeal to funky or traditional individuals? Next, take a trip to your local department store and take note of the colors that are being used for the upcoming season. Look at the jewelry and observe the lengths of the earrings/necklaces, the sizes of the stones, and the other various style elements for the season. While your designs should not be copies or replicas of the jewelry in the stores, you can simply incorporate the observations you make into your own original design ideas. Fashion and jewelry magazines are also a great place to find out what trends are coming into the stores. There will be an overwhelming array of gemstones and supplies at the show. Having a jewelry line style and color scheme in mind will allow you to narrow your focus. Vendors will offer gemstones in more shapes, sizes, cuts, and colors than you can imagine. Stick to the colors you’ve mapped out for yourself and walk through the entire gem show once before buying anything. Jot down and compare the prices of items that you’re interested in. Then take a break, go outside for some fresh air, and reflect on the items you saw and really liked. Then review your budget and the jewelry line you have in mind before returning into the gemstone show. Ultimate Small Shop Guide Download This will help you get the best deals on the items you’re most interested in so that you don’t blow your budget or become overwhelmed by the options. Soaring through the air, watching the clouds and the birds fly by.
I grew up in New Jersey and now live in the Pocono Mountains of Pennsylvania. Good thing, too, because we certainly need that extra property space to store the leader of the Auto­bots.Back in 2013, I founded an Internet company called AmericasFootprints.com, which gives people an opportunity to preserve their most precious memories (in private) for the current and future generations of their family. That’s because I believe everyone has a story and I also believe everyone deserves a chance for their story to live on.
The other aspect that separates the cost of ecommerce apps is the payment itself. As users add products, they'll need to check out and perform a payment transaction. Some of the tools above bundle in payment solutions. Alternatively, you'll have to integrate with payment gateways like Stripe, Braintree, Authorize.net, etc. Ecommerce apps that fall into this category include Amazon, Stitch Fix, Honest, and many others.
We love natural light as much as anyone, and the big windows in our van were something we were super excited about. But when you're living in a van, you'll want some privacy. Trust me. You'll also need curtains to keep out the lights when you're trying to sleep. Making your own curtains can seem like a daunting task, but it's not all that hard. (I speak as someone who had to look up a tutorial to operate a sewing machine!)

Once you have your space secured, hang some pictures in the windows that illustrate what’s to come. It’s also a good idea to provide leaflets that people can take away with them and hang a clipboard and pen on the front door where people can sign up to hear more about your business. This list is pure gold! So once you have it, why not stage a launch party and invite the local community (and local journalists). The first step for any business is always getting people to try out your products!
We're living in an age where we can order groceries, turn on the lights in our house, or get in a workout from the convenience of our phones, tablets, or other devices. Apps are a part of our everyday lives. They are increasingly giving us more free time or vying for more of our attention, depending on how we choose to use them. With that, here are some of the more important changes since we published our app cost article in 2015.
A dust mask or respirator will protect you while you're working, but won't do anything to protect you or your family from suspended particles still in the air. For this reason, an air filter is an absolute must if you work with woods indoors (I know of guys who sneezed out sawdust after working too long without an air cleaner). It's possible to make your own air cleaner out of box fans and furnace filters, but retail air cleaners will usually be much more compact. If you go that route, we recommend Wen 3410 3-Speed Remote-Controlled Air Filtration System for smaller shops.
You can see I broke the ultimate goal down into smaller tasks. Now you just need to do this for all the big goals that you have mapped out for the year. You may have more ideas or goals throughout the year and that’s okay. With this type of document, you are able to add another category and tasks anytime you want. This is just the best way to keep track of all the little things you need to do to accomplish your goals so you never are stuck wondering what you have to do next.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.

Great website! I spent a summer living out of a ford focus hatchback while road tripping around the United States. The rear seats were replaced with a small platform to store gear and the rear windows were tinted. I enjoyed the freedom that anywhere I parked no one would see me hop from the drivers seat to my platform for some zzz’s. Also no one would guess that someone is sleeping in a 3dr ford focus.


Well this is the same unit I have used for years so the noise level will be what it has been. I never turn it on without ear protection. In the future, I plan on building a little closet around the cyclone to help mitigate the noise to some extent. As for cycling the motor, I read that too. But the way I work, I just can’t do that. I have to turn it on and off as needed but I do try to limit it as much as possible by doing all of my heavy milling at once.

By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!

There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Before starting your small business and opening its doors, it is important to take some time to define your end goal. While it almost goes without saying that this goal will be subject to change, it is only by recognizing and clearly articulating your long-term ambitions that you can provide yourself with a compass that will guide every business decision.

Well, all these years we’ve always planned on this being a nice little workshop, and now’s the time that we’re about to remove all of this and create a nice realistic, practical workshop. Not a TV workshop that just looks good, but one that will be perfect for us to use for some of the projects we have on the show, and again it will be used by our construction company for some of the projects they have.
When registering your business name you should also consider whether or not you have plans to expand your local business nationally or online in the future. Registering your business with the state does not offer brand protection beyond the state it is registered in. For example: If Bob’s Bike Shop is registered in New York, no other business will be able to use that name in that state. However, someone in Idaho can still register their business as Bob’s Bike Shop. If you have aspirations that look beyond Main Street, USA and would like the option to expand nationally or on the web, you should consider trademarking your business. When you trademark your business name, it makes it a lot easier to recover property that infringes upon your brand. For example: If Bob’s Bike Shop in Ohio purchased the domain www.BobsBikeShop.com but Bob’s Bike Shop in New York trademarked that name, legally Bob’s Bike Shop in New York has the right to file a domain name dispute to get the domain name back from it’s current owner.
Note: Some of the links to products that we recommend on this page are affiliate links. This means that if you click through one of our links and buy something, we get a small commission at no cost to you. This helps us keep this blog going so we can continue to provide you with van build tips, tricks, and guides. We believe in honest opinions, and we never recommend anything we don't know about. Every recommended product on this page we've either used personally, have personal experience with, or have researched heavily.

Debt financing involves borrowing capital that must then be paid back over a set period of time, most commonly with interest. Typically the core benefit of this arrangement is that you, the business owner, maintains complete control over your business. Your only ongoing obligation is to repay the loan with interest. The downside? Fail to keep up those repayments and the loan — often secured against your assets, savings or property — can put you in very dangerous financial waters.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
The good news? There are a ton of free tools out there help you simplify and minimize the research required to secure your online identity. Among them is Namechk, a free username and domain search tool that helps you discover the availability of your business name across hundreds of social networks and domain extensions, all at once. Once you run a name search and confirm that it’s available for use both off and online, take the time secure your unique name both legally and on the web.
The thing I wanted to mention was that I moved from Seattle to Loveland, Colorado north of Denver in July ’05. I brought my ’01 Dodge Ram 2500 with a 8.5′ Northland Grizzly slide-in camper. It was myself and my 9 year old Black Lab mix Lucy. One thing I had not anticipated was the temperatures here in Colorado. It was 105-106 degrees for the first week I was here. My job was in Boulder, which is known for its “bunny-higher” types. I couldn’t leave Lucy in the camper at the RV park because I didn’t have air conditioning in the camper. I took her to work with me and tied her long rope to the trailer hitch on the truck so she could crawl under it and get into the shade. I also put out plenty of cold water for her that I replenished often. By the afternoon of my first day at my new job I heard rumors that people were going to call Animal Control on me for having my dog outside in temperatures that hot, even though she had both shade and water. I ended up having to leave early my first day so I could go purchase a $600 air conditioner and install it in the camper so I could leave Lucy there during the day and I didn’t have to worry about her comfort.

The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
Have a walk-through yourself and see where the visual cues guide you or get your staff, friends, or family to do the same and give you honest feedback. Don't forget to observe your customers and see what they're drawn to, what they avoid, and how they move, then match that with your intended design. If you keep resilient and keep your eyes and ears open, you'll be sure to create a retail design that's a win-win for both you and your customers. 
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
A commercial real estate lease is a long-term rental agreement between the landlord of a commercial space and a business. There are many types of commercial leases and many types of commercial spaces. Leases include full service leases, net leases, and modified gross leases. These leases help tenants rent out office spaces, retail and restaurant locations, as well as industrial spaces.

He’s also providing power to a cool light grid we’re building from several old fluorescent fixtures that we salvaged from past remodeling jobs. With six four-tube fixtures, we should get plenty of light. In a work space you want to install these lights high enough so they don’t get in your way when you’re moving materials but low enough to provide good even light.
While the recession brought with it a well-documented squeeze on small business lending from banks, there are a number of alternative funding sources available to those who are starting or expanding their small business. Loans and/or equity investments can be sourced from multiple sources, including credit unions, savings and loans, and private financial companies. Family members, friends, and colleagues are also potential avenues to explore.
In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
Hey thanks for the great insight on a pickup camping setup! I just purchased a 2002 tundra with a 74″ bed. Picking it up in Denver in a week and driving it to Durango and then around the southwest. I mainly decided on a truck for a mobile place to keep my dog(that doesn’t have an interior he can rip to shreds), but I am thinking of building a setup similar to yours. You haven’t used yours with a canine companion have you? Any suggestions on keeping it dog-friendly, dog-comfortable and dog-proof? I will be keeping him in the back while at work and such and will be camping in the back with him and possibly another person.
I don’t own a dog, but I have taken my buddy’s two dogs out with us to the trailhead at least. Not sure that I have great recommendations for how you would go about living in the truck with your dog. All we really did was lower the large wooden deck to the bottom position, throw down some soft doggy beds and pillows, then cover it all with a giant blanket which also covered like the side bins to keep dog hair from getting all over. It was nice and cozy for the dogs while driving down the road. Then we just put packs and other gear on/in the side bins. We used some big metal clamps to secure the blanket to the side bins and keep it from falling down or sliding around. I would think avoiding any carpeting would be a good bet, just go with blankets and things than can be taken out, cleaned, and you can sweep out the back.
Composting Toilet: Nature’s Head Dry Composting Toilet. Much more expensive but also more pleasant and environmentally-friendly. Just drop your load and add some peat moss/sawdust, and your toilet will naturally break down your poop into compost. If the Nature’s Head toilet is out of your price range, you can also try making your own composting toilet.
I framed in a 4x8 Garden Shed on the back.  I didn't want it so deep that stuff would get buried in it.  I need to take an updated picture of the back.  These pics were from early on and I have changed some things in the organization.  I used similar framing techniques and built a lean to roof attached with metal hangers.  I chose to use clear corrugated roofing to allow natural light into this shed.  You can see the 2 shopvacs that were originally part of my simple vacuum system.  I have removed them and found that I get better airflow using an electric leaf blower with the vacuum attachment hooked up to my system.  There is a large metal trashcan with a dust collection separator to collect the larger pieces of saw dust and chips.  My air compressor is on a shelf on the right now and I ran a hose through the wall and to a 25 foot reel attached to the ceiling.  I wired separate switched for both on the inside of my shop.  These systems work extremely well for a small shop.  The wall provides some insulation from the overwhelming noise they would otherwise create inside the shop.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
×