If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percent­age of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both dif­fer depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.
Ralph has three decades of professional experience in using workshops and setting them up, and it certainly shows in his Ultimate Small Shop guide. You’ll find all the important information you need to put together your own workshop, including how to save money when putting one together; all the tools and equipment necessary to run a workshop; tips for choosing the best equipment; factors that should be considered when buying things for the workshop; and so much more. If you’ve considered setting up a workshop but feel you don’t have the time, space, or money – then you need to check out Ultimate Small Shop – How to Set Up a Complete Small Workshop on a Budget.

Ordinary clip-in-place shelf brackets with slotted metal supports can hold a lot of weight. But some-times they’re unstable and can be easily knocked loose. The play in the slots allows the bracket and shelf to shift from side to side. To prevent this, use your circular saw to cut 1/8-in. deep slots into the undersides of the shelves, aligned with each bracket. When the shelf is assembled, the brackets fit into the slots, eliminating the sway. Also check out: How To Build Floating Shelves.


Now I want you to create a spreadsheet or use my worksheets and write one major goal on the top. This can be the first goal you want to accomplish. Then I want you to list all the tasks you need to do (or someone on your team has to do) in order to accomplish this task. For example; let’s go going back to the goal of "Launching a New Website". The tasks you will need to do to get this goal accomplished are the following;
Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.
As Kizer & Bender always tell retailers: Put it on paper. If you haven’t settled on your store layout—or even if you have—the first thing you need to do is work your plan out on paper before you start moving things around in your store. Putting it on paper helps give you a clearer picture of the desired result and any potential issues before getting started. Remember, many small retailers find that a mix of floor plan and layout styles works best.

I don’t own a dog, but I have taken my buddy’s two dogs out with us to the trailhead at least. Not sure that I have great recommendations for how you would go about living in the truck with your dog. All we really did was lower the large wooden deck to the bottom position, throw down some soft doggy beds and pillows, then cover it all with a giant blanket which also covered like the side bins to keep dog hair from getting all over. It was nice and cozy for the dogs while driving down the road. Then we just put packs and other gear on/in the side bins. We used some big metal clamps to secure the blanket to the side bins and keep it from falling down or sliding around. I would think avoiding any carpeting would be a good bet, just go with blankets and things than can be taken out, cleaned, and you can sweep out the back.


Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
Inventory management — especially when first starting a small business — at its most basic level consists of counting how many of a given product (let’s say apples) you have for sale in the morning, keeping track of that number, then reducing it by one each time an apple is sold. At the end of the sales day, you count the leftover apples and make sure the number of apples in your inventory system matches whatever you actually have in store. When you have an accurate apple count, you call your supplier and order as many as you need to make sure you have enough on hand for the next day.
In our Complete Coffee Shop Startups Kit, we spend a good amount of time discussing your health department requisites, your coffee equipment, and even the design of your coffee shop. Since this makes up a significant bulk of your startup costs (equipment, space requirements, etc.), we recommend that you spend an extra couple of hours strengthening your knowledge base with listening to our audio interviews.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Now, we’ve already applied some resurfacer to fill up some of the deeper holes and after that dries overnight we’ll use a floor leveling compound tomorrow morning to really smooth everything out. Leveling compound is more fluid than the resurfacer so it flows into all of the low spots to even out the surface. Now, this won’t look like a finished floor when Tim’s done but it should do the job for our shop. Now, while he wraps up this Emily has a Best New Product that might be a great addition to your workshop.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
×