SBA provides support and tools to aspiring small business owners and in particular to minority-owned, women-owned, disadvantaged, and veteran-owned businesses, including a government-backed financing scheme to qualified participants. Local and state authorities also have a range of programs designed to encourage the growth of your small business. Make sure to research your local authority’s website.
We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.
“Zone design successfully helps shoppers locate what they want while exposing them to products that enhance the ones they are buying. Increased transaction totals are a natural byproduct. Products are categorized by use into Zones, such as ‘kitchen/cooking,’ ‘entertaining/dining,’ and ‘home decor,’ with inventory range and stock levels determining the size of each Zone.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appropriate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with homeowners and builders to make sure that the work will meet code and will endure.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
I am a firm believer in having your business goals align with your personal goals. In order to do that, you need to know what your personal goals are. This may be different for everyone, but I want you to be 100% honest here. I am writing this as an update in 2018 to this original blog post and I want to be honest and share with you my personal goals for 2018:
The way that you fill these roles will depend on the size of your company and how much you’re hoping to invest when building your marketing team. If, for example, you’re looking to bring on a single marketing employee who will handle all these functions, you’ll need to find somebody with a broad set of experiences and the ability to handle multiple job roles.
I was really excited after seeing your shop video. It was almost like you read my mind (except my plans does have more windows and a wood burning stove as I live in TN). I realized the importance of more 22o plugins after you explained your reasoning. I was just planning a couple. Love the floor and ceiling plugins. One quick question. Is each plugin area on it own breaker, or do you have more then one on each breaker. I was planing on each one to have its own breaker. Love your approach on your projects and how you introduce new items or products. Thanks and Merry Christmas
What I have done in my man cave of a shop is to install above my finishing table a strip of track lighting where I have fixtures ranging from the typical bright white incandescent (typically around 4700k) all the way to the average halogen spot that I figure someone would use with an art piece (normally around 3700K). this allows me to point each light and view my piece and finish under varying light conditions to judge whether or not I prefer a particular finish or not. It also helps in photographing items (though filming is a whole nother story, I still have my 5400k T8 overheads for working).
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wiring for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to finishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a programmable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
In a small space, there's not much room for one-trick ponies: You need gear that can do many different things, and that goes for your work space and stands, too. You can add a wood clamp to a multifunction workbench, but you probably need compact work or tool-holding stands to make up for the lack of a large work surface. Occasionally you may need to take your work to another room or even outside, in which case portability is also important.
Let’s say you’re a Brooklyn-based hipster and you want to follow your lifelong dream of opening your very own artisanal, organic lemonade stand. You’re planning on stationing your retro lemonade stand along a busy road in Williamsburg, Brooklyn. And maybe you want to hire a couple of college kids to collect the money and serve your customers, (probably while wearing some painfully cool 1970s punk band t-shirts). You’re only thinking about it semi-seriously. It might be something you’re going to do when you’re not focusing on your real career as an aspiring DJ.
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
Of all the LED lighting options, puck lights are the most difficult to install. You’ll have to run wiring behind the ceiling/walls for each light. And you’ll need to cut a hole with a hole saw to recess the lights into the ceiling. But with some preparation and care it's not too difficult. We have full instructions for installing LED puck lights in our epic electrical post.
If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.