So what’s the downside? Well, for starters, RV conversions aren’t exactly known for quality. Most manufacturers use cheap (i.e. shitty) materials, and just don’t build their vehicles to withstand the stresses of full time living. You’re also locked into a pre-designed layout, so it will be a lot more difficult to customize how everything functions.
I don’t have recs because I’ve always just gone the traditional cold weather camping route with warm clothes, winter sleeping bag, boiled water in a nalgene, shot of olive oil before bed, etc, etc. Perhaps someone else might chime in… I’ve heard of folks (with the appropriate dual battery setup) using electric blankets, or yeah, the Mr. Propane heater (but not while they are asleep).
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
However, Sprinters are a lot more expensive than other options. It can be tough to find anything reasonably priced with less than 200,000 miles. For the Mercedes Sprinters, parts are more expensive and it may be difficult to find mechanics that have experience working on them (this is less of an issue with Transits and Promasters). And, since these are complex vehicles, they don’t lend quite as well to tinkering as something classic like a VW Vanagon or old Ford Econoline.
I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key storage, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
If you are going to apply for a trademark, make sure to conduct a comprehensive search, like the one mentioned in ‘Securing Your Business Name’ to ensure no one is already using your proposed name in a similar capacity. The United States Patent and Trademark Office also provide a simple search tool that will quickly let you know if you’re potentially infringing on someone else’s turf from a legal point of view.
If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
This holds a lot of stuff but mainly our handheld power tools, so it needs to support a lot of weight. Any shelf in a workshop will probably wind up supporting more than you initially planned so build it as strong as you can and don’t scrimp on the materials or the fasteners you use to hang it. Now the next step is to install our recycled cabinets that will line the wall under the shelf. Now these cabinets are a little plain but that should work great for a shop like this. Even if you don’t own a remodeling company you can usually find these things pretty inexpensively from salvaged warehouses which recover them from renovation projects then resell them to the public.
Tired of the rat race, I opted for early retirement. Looking for something to do with all my free time, Ultimate Small Shop Ebook Free I started crafting and am now making a nice supplemental income from it. As a crafter and a businesswoman, I feel I have some valuable insights into the craft business that I can share with you. At some point in your progression from crafting for fun to crafting for fun and profit, you go from handcrafting individual items for yourself and friends to filling quantity orders for a broader marketplace. That’s the time to take a very business-like approach to your craft business. This needn’t be daunting. You don’t need an MBA or management experience – just a bit of common sense. If you’re going to do this for profit, you need to understand Simple, right? But very few people get it. Look at the high failure rate for new businesses. It takes an effort to be successful, but the task is hardly impossible. Traditional craft retailing methods are what most crafters use to get started. They’re the easiest way, especially if you don’t know if anyone will buy what you make. I believe that there is a market for any well-made craft, whether decorative or useful. The problem facing many crafters is how exactly to go about selling them, or more accurately, finding paying customers. The fact is that there is an awful lot of competition out there. My own business got jump-started by my “circle of friends”. Ultimate Small Shop Free My friends noticed and liked my calling cards and began to ask me to design and make cards for them. Starting with just Broderbund’s Create-a-Card program, I was soon earning a nice supplemental income in just a few hours a week. It probably helped that I was retired and live in an area dominated by retirees. But I think that everyone has a “circle of friends” either socially or at work. Of course, you don’t want to impose on their friendship by making a hard sell, but rather use or display your crafts in front of your friends to see if they draw any interest. If they do and if they’re priced right, you’re on your way to craft retailing for profit. If your “circle of friends” market starts extending to friends of friends, you’re probably ready to tap the general marketplace of craft retailing. Most crafters are aware of the periodic craft shows put on by local groups or even by the local Parks Departments. These usually cost little or nothing to join and should give you a fair idea of whether there is any broader interest in your craft. What better way to jump into craft retailing? There are also organized craft shows that tour the country, Ultimate Small Shop Legit most of which charge an entrance fee for participants.
Tight control of inventory, while not a particularly glamorous part of owning a small business, is therefore one of the most important ways you can impact profitability. The good news now is that there is an array of technology available that can make this whole process much smoother, including sophisticated forecasting tools that will help you predict your required inventory levels for each day based on past sales, weather records, and many other factors.
If you’re moving into a space that requires renovations in order to fit your business needs, you’ll also want the landlord to take on responsibility for that work. We’re not talking aesthetics here, we mean necessary renovations such as improved data connectivity. If you have to do the work yourself, it’s advisable to ask the landlord for a rent-free or reduced-rent period. You should also make sure that any additional alterations you have in mind are acceptable and would not be in breach of the lease. Last but not least, always make sure the do’s and don’t of what can and cannot be done is put in writing, it will save you a lot of headaches later.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code conventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow foundation may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the concrete slab will structurally bear the weight of the shop structure you build above it.
The more outlets the better! I have a good mix of 220v and 110v outlets throughout the shop. I even included a few in the ceiling and the floor in hopes of avoiding power cords in the walkways. And although this contradicts my previous comments about over-committing, I picked locations that would likely work for various tool configurations. If at some point they don’t work for my setup, I just won’t use them.
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.
After looking at a number of spaces that are available to lease, you may start to wonder whether it’s better to buy or lease commercial real estate. Of course, there are occasions when it might be better to purchase commercial real estate rather than leasing it. For example, if you buy a commercial space, you’ll take advantage of equity, depreciation, cash flow, and asset appreciation.
Both of those broader lenses are still useful ways to look at app costs, but costs can additionally be broken down by app type and the features associated with them. Also, two years in technology is a very long time. So, we will start by looking at what's changed. We'll then move on to looking at app costs based on the different kinds of apps in the market.
We all know that we’re not supposed to judge a book by its cover. The truth is however, that it’s human nature to judge based on appearance. Though most of the time, despite our good intentions, it happens unconsciously. As consumers we make incredibly quick decisions about the businesses we choose or choose not to frequent. As we enter a location we take in the signage, the windows, and the product displays. And with the blink of an eye we determine a dozen different factors. Is this location trustworthy, clean, and friendly? Is the staff likely to treat me well? Will the products be to my liking? Will I find what I need and complete my purchase quickly? Can I even afford to shop here? And, perhaps most importantly: Is there something unique about this place?
The first is that they will need to be powered by a product catalog. Many times that already exists and an app will just leverage APIs or web services to pull back products. If it doesn't, however, it will require either a custom buildout (beware!) or leveraging platforms like Shopify, Magento, or comparable solutions. The strength of these tools include providing the administration interface to add new inventory, APIs or SDKs, ways to store items in a cart, and similar features. The downsides are that you'll be limited by their workflow and customizations.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
I wanted to have numerous outlets, and have enough electrical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
As the old saying goes, the only two inevitable things in life are death and taxes. Almost all small businesses in the United States are subject to some form of corporate income or gross receipts tax on a state level — that is, unless you happen to be a lucky inhabitant of the great states of Wyoming, Nevada or South Dakota. Actually, even these states will require you to pay state workers' compensation insurance and unemployment insurance taxes. Oh, and of course every small business in the country is subject to some form of federal taxation.
I will challenge myself to use this space creatively to tell the story of each year. Ultimate Small Shop Guide When I started thinking of all the possibilities, it really inspired me to start getting organized and collecting some great memories. And don’t limit yourself to just photographs, your scrapbook pages can really be accentuated by other types of memories. Here are some ideas to get you started. Looking for some great Halloween crafts for your Halloween party, haunted house, or just for trick-or-treaters? A fun craft is something that can keep you occupied for hours on end especially if you enjoy it. Here are some ideas that will hopefully set you on your way in preparation for your next Halloween…If you live in a house that has a wood-burning fireplace, then chances are that you have access to tree stumps or large blocks of wood. These are great for making stands for your Jack O’Lanterns. You could use a chisel to slightly hollow out the middle of the stump so that the lantern can sit stably or simply use some Blu-Tack or Velcro. Get some small or mini pumpkins and hollow them out to use as candle holders. If open flames are out of the question, you can put glow sticks instead of candles for a different effect. You can carve, draw or paint faces on the pumpkins too. Instead of pumpkins, you could use apples as well. Ensure that you choose apples that sit well and flat or cut off the bottom to make a flat surface. Remove the stem and cut around it deep enough for the candle. It is best to use taper candles for a better fit. Get a large pumpkin and hollow it out to use as a salad bowl or to serve fresh vegetables. Cut off the top, hollow and clean it out and let it dry in the sun. You could carve a jagged edge design on the top. Do the same with some smaller or mini pumpkins to use for dips or salad dressings. Make a scarecrow in your front yard. You need two pieces of wood, one put into the ground and the other nailed across for the arms. Use old jeans and a shirt and stuff them with newspaper. Add some straw for effect. You can use a plastic pumpkin for the head and draw a face on it. This makes a great Halloween craft for the whole family. Tie glow sticks to helium balloons and let them float around the house. Ensure that some string extends below so that people can easily reach them if they get stuck somewhere or simply to play with them. Use publicly available Halloween fonts on your computer to make banners or invitations for your party. It’s a fast, easy Halloween craft you can use instantly to enhance your party theme. Ultimate Small Shop Book Print them onto inkjet iron-on transfer paper and put them onto your favorite t-shirt or Halloween outfit. A visit to your local hardware store for some basic items and you could make your own tombstones transforming your garden into an instant graveyard. Paint them grey to resemble stone. Do not worry about the details as it will be dark, but do put on some exciting or scary wordings. By the way, your local hardware store is loaded with Halloween craft ideas.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.