This is where I started thinking about how I was going to store all of my lumber.  I had planned on building a wall rack, similar to what I had used in my single car garage.  But I hated using up an entire wall for lumber storage.  I also knew from experience that I would easily lay stuff against it and soon be digging lumber and junk out of my way.  I decided to use the space under my workbench to store the long boards and I realized that by pulling my bench out from the wall I could slide sheet goods behind it.  This created a problem:  How do I get it out.  The Shop isn't long enough to pull out 8 foot boards from inside and I would probably have to move things around to get to it anyway.  So my plan for this came at kind of a sudden epiphany moment, when I decided to cut access doors in the front and build my storage into my workbench area.  This has been the single best idea that has come out of my shop.  I can't express enough how easy it is for me to get straight to a board i need with no hassles.  I just remove the doors and pull out what I need.  I can store a surprising amount of lumber in this area.  I do have a secondary area for some cutoff sheet goods and a scrap bin next to my table saw in the garage.  But this area stores most of my lumber.
Tired of having your caulk tubes lying all over the workbench or your shelves? Make this organizer from a scrap of 2×8 and a piece of 1/4-in. plywood. Just lay out a pattern for your 2-in. hole saw to follow and drill holes through the 2×8. Then glue the plywood to the bottom. Now you can set it on a shelf and easily identify the tube you’re looking for. — Burnie Lorenz
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.

One thing I found while looking on the topper websites is a piece of weather strip designed to go between the tailgate and the truck bed. It has a special wedge shape to it so when you close the tailgate it makes a watertight seal. It is just the thing to keep the dust and dirt from entering the back of your rig when driving down the dirt roads. They’re inexpensive too, for a full size truck like my Dodge it’s only $25. It has adhesive on one side, so installation looks simple.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.

If you are going to apply for a trademark, make sure to conduct a comprehensive search, like the one mentioned in ‘Securing Your Business Name’ to ensure no one is already using your proposed name in a similar capacity. The United States Patent and Trademark Office also provide a simple search tool that will quickly let you know if you’re potentially infringing on someone else’s turf from a legal point of view.


In my opinion, the best shop space is a flexible one. I know many folks expected that after setting up my shop so many times, I would be able to design the PERFECT shop space including a finishing room, a dust collection closet, and even some internal walls. But the truth is, the most important lesson I learned over the years was to expect change. My shop is not a static entity. It is more like a living breathing creature that adapts, evolves, grows, shrinks, and changes configuration. Committing to an internal spacial arrangement too early could yield disappointing results. This is why you won’t see me placing dust collection ductwork in the floor. I need to work in a space for at least a few months before I can be confident in my initial setup. Even then, I fully expect things to change at some point. If I made too many restrictive and/or permanent decisions ahead of time, these changes could be difficult or impossible to implement. So my best piece of advice is to forget about the concept of perfection. Instead, focus on flexibility. The ideal shop, in my mind, is little more than 4 walls, a roof, and a butt-load of outlets and lights. So here are some of my basic general goals for my new shop space.

One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
We exhausted our entire life savings on this project and entered into a lot of debt at the same time. And now it’s the ongoing maintenance, repairs, insurance, and upkeep on this rig that make it almost impossible for us to keep it on the road. This is where I’m hoping to get that “let’s sponsor you to travel across America and meet the fans” call from Hasbro or Paramount one day soon.
He’s also providing power to a cool light grid we’re building from several old fluorescent fixtures that we salvaged from past remodeling jobs. With six four-tube fixtures, we should get plenty of light. In a work space you want to install these lights high enough so they don’t get in your way when you’re moving materials but low enough to provide good even light.
Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well. 

Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well.

Ryan, I have the same (almost) 90’s Toyota Pickup and love it! this is so helpful, and I will definitely be using this method. my main concern is that 1/2′ plywood sagging. do you notice it sags quite a bit or does it mostly hold up? my thought was to build the vertical bins a little wider, so that the plywood bed platform wouldn’t be under so much stress. the second issue im running into is wrapping my head around trying to organize and compartmentalize things appropriately. what do you typically put where so it is easy to reach and use?


Although the market has even more options to build apps now than in 2015, there's also clearly more of a distinction in quality. The best app firms and app developers have further honed and distinguished themselves. They have more awards, stronger portfolios, better team members, and more specialized skills. The tools available have made it easier to build apps though, so there's also many more mediocre or low-quality options to build your app.
The refrigeration setup in your van is an area where you really do get what you pay for, whether you’re paying in money or in time. The best options are the most expensive. The cheapest options are a pain and/or don’t work very well. And if you try to save money with a DIY refrigerator setup, you could end up spending a lot of time on installation.

Ultimate Small Shop

×