However, another critical component to small business success is being self aware. With a variety of tools at your fingertips, tracking basic accounting can be fairly simple. Still, in order to be strategic about how you spend your money, properly leveraging these tools will still require a little bit of legwork. What used to take you eight hours might now only take one hour. But if you’re not willing or able to run through your financial tasks on a regular basis, bringing in a bookkeeper or accountant might be your best option.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on. The rewards aren't usually good enough to compel me to purchase on their own. But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
Well, my workshop is finally complete and I’m ready to take on just about project that comes down the line. And I’m pretty well set up here. I’ve got a great workbench, plenty of table space over here that easily rolls around the shop if I need it, lot of storage space down here, I can tuck these tools away or bring out any new ones that I need. And as you can see I’ve got plenty of supplies to tackle just about any project.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
First, as most eager but hesitant potential hobbyists realize, you have to be much more thoughtful about tool selection. A 14-inch band saw? In your dreams. In a small space, you're going to have to rely on bench-top or handheld tools. (It is possible to forgo power tools entirely in favor of hand tools, but that's a discussion better left for another time.)
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
For years my wife and I had agreed that we would one day leave Oklahoma for someplace we really loved. That day finally arrived last year when we found a home in Vancouver, Washington that met our dreams. Only thing missing was someplace for a woodshop. Well, there was a place, under a deck, but not a room. So, as part of the move we had a local contractor build a room that would one day be the wood shop. Fortunately there was already a door from the house into this area, and about half of the “walls” were there, in the form of concrete retaining walls.
The good news? There are a ton of free tools out there help you simplify and minimize the research required to secure your online identity. Among them is Namechk, a free username and domain search tool that helps you discover the availability of your business name across hundreds of social networks and domain extensions, all at once. Once you run a name search and confirm that it’s available for use both off and online, take the time secure your unique name both legally and on the web.
As Kizer & Bender always tell retailers: Put it on paper. If you haven’t settled on your store layout—or even if you have—the first thing you need to do is work your plan out on paper before you start moving things around in your store. Putting it on paper helps give you a clearer picture of the desired result and any potential issues before getting started. Remember, many small retailers find that a mix of floor plan and layout styles works best.
For now we’re just getting it out of the room so that our electrician can get started. In any kind of workshop you want plenty of access to power and lots of use of the light. So Mike our electrician is hooking us up. If a service call from an electrician isn’t in your budget you can plan your space so that you can best take advantage of the outlets that are already there. Now Mike has checked all of these surfaces to be sure they can handle these extra outlets he’s adding.
In as much as I am a clamp freak, I needed some way to organize clamps without spending a mint on brackets. In our previous house we had a number of glass shelves –which I didn’t plan to put up here. But, the brackets were great – I laid in two tracks next to each other, then took a pair of the shelf brackets, cut a piece of 9/16 x 9/16 x 3 inch pieces of wood – put the wood between the brackets, shrunk wrapped around the brackets and wood, and came up with some really stable clamp hangers.
With all the time and effort you've put into properly merchandising your products, the last thing you want is for incoming customers to hurry past them — this ultimately limits the number of products they'll purchase. One way retailers combat this is through creating breaks that force them to pause. These are sometimes referred to as "speed bumps." Essentially, this can be anything that gives customers a visual break and can be achieved through signage or special/seasonal displays.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
To avoid buyer’s block, define the core characteristics you absolutely need in your business. Write them down in a prioritized list ranked from ‘deal breaker’ to ‘would be nice to have.’ Now cross off the bottom five and focus only on the ones that are left. Compromising is essential in choosing a commercial space, especially in popular neighborhoods. Besides, you’d be surprised how what once seemed like a less than stellar storefront can become your dream location once you get those creative juices flowing.
Making sure any holes in your insulation are sealed off and filled helps your insulation really do its job. Great Stuff Gaps and Cracks spray foam insulation is the best way to fill in any space around your foam boards, and to insulate any hard-to-reach spots. You can also spray this into the hollow vehicle frame for insulation (you’ll need a whole bunch of cans for this).
Whether you end up looking at self-checkout counters, fancy lighting systems, special refrigerated cases, or any of a countless number of options, never forget that these are only tools to help accomplish your main goal. Your store needs to create an environment where customers want to be, where they feel comfortable and appreciated, and where that experience will prompt them to purchase (and hopefully encourage their friends to do the same). Equipment and technology decisions should always be made with your customers in mind.
We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
We all know that we’re not supposed to judge a book by its cover. The truth is however, that it’s human nature to judge based on appearance. Though most of the time, despite our good intentions, it happens unconsciously. As consumers we make incredibly quick decisions about the businesses we choose or choose not to frequent. As we enter a location we take in the signage, the windows, and the product displays. And with the blink of an eye we determine a dozen different factors. Is this location trustworthy, clean, and friendly? Is the staff likely to treat me well? Will the products be to my liking? Will I find what I need and complete my purchase quickly? Can I even afford to shop here? And, perhaps most importantly: Is there something unique about this place?
Now, another thing we’ve recycled that’s kind of unusual, all the wood walls you see here were actually and old backdrop that we used on a show a couple of years ago, perfect for our wood walls we need. Now, to store some of the tools, we have we created this simple little shelf unit out of cedar. And you know it kind of adds some of that warm wood feel to a shop, which I wanted it to look more like this than just plain painted walls.
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution.
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.
Love the design. I’ve got a 15 tacoma, which has rails that run the length of the bed and are what my shell is “clamped” into via a bed rail nut. Hence my problem with following your outline verbatim. Any suggestions for incorporating the rail as a substitute for the 2×4 you clamped into your truck? Essentially connecting the 3, 2×4 braces directly to the rail… I’m a construction novice, any suggestions greatly appreciated!
However, since you may not have "aisles" per say in your store, it's still important to think about grouping products in a way that makes sense from a shopper's perspective. Also, remember to keep "higher-demand" products displayed at eye-level while placing lower-grossing products at the bottom or above eye level. Lastly, It's recommended that you change up these speed bumps weekly or regularly enough to create a continued sense of novelty for repeat visitors.
Shops have value on many different levels. There is the satisfaction of having a place to create and work on projects that is hard to quantify, but definitely improves your quality of life. There is the value to your small business of having space in which to work wood and thereby generate income. There is the dollar value of the build itself, which will be a considerable investment and, finally, there is the resale value of your property after you’ve added your shop. Before you go too far, though, it’s worth asking a local real-estate agent about the potential return on your investment in your area; generally shops won’t add significantly to the value of your property, so it’s worth thinking carefully about what else the space could be used for if you were to sell. The decision about whether it is worth it to build is a matter of balancing all these factors: projected sales balanced against the cost; the cost of building is balanced against what it will be worth when you sell. Woodworking can be a creative outlet, can give you a sense of mastery, and even be a way to give back to your community by donating beautiful pieces to local charities for fundraising auctions, or creating pieces that future generations will inherit. Ultimately, the value of a shop might come down to the emotional and social returns that it will pay you and the people around you for years to come.
A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
The refrigeration setup in your van is an area where you really do get what you pay for, whether you’re paying in money or in time. The best options are the most expensive. The cheapest options are a pain and/or don’t work very well. And if you try to save money with a DIY refrigerator setup, you could end up spending a lot of time on installation.