I live in Northern Va and have the same concerns. I save those little silica gel packets every time they come in a new product and put them in my tool drawers. I also salvaged a dehumidifier from a neighbor that I need to repair and set up in there. I use the wall mounted AC in the summer to keep it cool enough to work in there. Although I haven't gone back yet to insulate the ceiling, it stays really cool in there if i want it to be.

I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.

These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.

If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”

Shop looks great Marc, I see the Clear Vue in the picture. I love mine, I used 8″ PVC for the main trunk line and came out of that with 6″ drops. It works great. I wound up building a collection bin instead of using a can, only thing I didn’t do was make the bin big enough. It holds more than the typical can but I still should have made it with more capacity. The 1800 with the 5 hp motor is stout.
Well, all these years we’ve always planned on this being a nice little workshop, and now’s the time that we’re about to remove all of this and create a nice realistic, practical workshop. Not a TV workshop that just looks good, but one that will be perfect for us to use for some of the projects we have on the show, and again it will be used by our construction company for some of the projects they have.
Hey there Ryan. Cool blog! I love the idea of trucking-it! I’m not able to do something like that, though I wish that I had taken the time when I was younger to do so. Here’s a suggestion that you might consider, if you haven’t already considered it before: Obtaining and using a hammock. I’d suggest bolting in an eye hook on the truck, or using the bumper as a tie point if you don’t have a second tree around. Also, in the high desert, you could use rocks as anchor points for it. Just an idea, from one camper to another.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
My husband is always hounding me about wearing eye protection whenever I use power tools. (Admittedly, I could be more diligent about it.) So, he recently glued some small magnets to several pairs of safety glasses and stuck them on all the power tools in our garage that have metal housings. Now it’s fast and easy for me to grab the glasses when I need them, and I’m reminded that my husband loves me. — Lisa Yanda. Here’s the other must have safety gear every DIYer should own.
Before starting your small business and opening its doors, it is important to take some time to define your end goal. While it almost goes without saying that this goal will be subject to change, it is only by recognizing and clearly articulating your long-term ambitions that you can provide yourself with a compass that will guide every business decision.

Now, photographs or video tape will also be very useful especially to pass along to your insurance adjustor. Now the problem is this documentation won’t help you at all if it’s lost or destroyed so consider saving your information electronically. Take your photos with a digital camera and create a list of all your valuables, and save both in a computer file. This file can be saved to a disk you can keep at work or upload it to a website that you can access it from anywhere including your home.
The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution. Small woodshop workshop on a budget
×