The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
Love the design. I’ve got a 15 tacoma, which has rails that run the length of the bed and are what my shell is “clamped” into via a bed rail nut. Hence my problem with following your outline verbatim. Any suggestions for incorporating the rail as a substitute for the 2×4 you clamped into your truck? Essentially connecting the 3, 2×4 braces directly to the rail… I’m a construction novice, any suggestions greatly appreciated!

Our Advice: Plan for aisle and display pathways of at least three feet, six inches wide, without obstructions. Then, once your fixtures and displays are in place, further test your store’s pathways by rolling a large baby stroller throughout your store. If you can easily navigate all traffic pathways, your customers should enjoy a comfortable browsing experience.


I don’t think you have run into this problem, but I have to deal with condensation in the cap as I live in a moist climate. I was thinking of an old van type roof vent with fan for active ventilation, or drilling holes along the side of the cap, inserting short cuts of pipe with fine screens (mozie land), and capping them. This way I could control for rain, cold, etc., but create some passive cross ventilation at roof level.
We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.
Skoolies do have significant drawbacks, however. Their size makes them a bit unwieldy to drive, and getting to some of the more out-of-the-way camping spots just won’t be an option. If something goes wrong mechanically, it can be much more expensive to fix than a normal vehicle. Also, the sheer size of these vehicles means the gas mileage is much worse than other options.
First, try to remove all the extraneous household items that don’t facilitate making stuff. In a perfect world, you wouldn’t have to dig past kids bikes or empty luggage to get to your paint supplies. In the real world though, storage is hard to come by, so you’ll have to give a little to get a little. Consider a line of demarcation in your garage to separate “household” from “workshop.” If you don’t have enough room, consider a smaller-space workbench, or rent off-site storage. You could even build a shed for more covered storage.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Do you create, collect, or curate anything special? Consider starting an ecommerce store and turning your hobby into a full-time job. Whether you need somewhere to sell all that pottery you’ve been making, or an excuse to search for the sports memorabilia you love tracking down -- an ecommerce store can make it financially viable for you to pursue your passion.
We have LED puck lights in our van. Puck lights are typically recessed into the ceiling, so they have a very clean look that’s really integrated with your van. It’s also easy to create different lighting zones by running your lights off different switches. We have six puck lights in the main living area that are controlled by one switch, and two more over the bed that run off a separate switch.
Our Advice: Plan for aisle and display pathways of at least three feet, six inches wide, without obstructions. Then, once your fixtures and displays are in place, further test your store’s pathways by rolling a large baby stroller throughout your store. If you can easily navigate all traffic pathways, your customers should enjoy a comfortable browsing experience.
Most of today’s POS systems have integrated inventory management software that allows you to put hours back in your week, whatever the volume of your stock. A quality point of sale system will allow you to manage pricing changes, track product availability, cross-check inventory, and automate reorders with ease. All of which are crucial in helping you develop a deeper understanding of your business, enabling smoother day-to-day operations and smart purchasing decisions.

Note: Some of the links to products that we recommend on this page are affiliate links. This means that if you click through one of our links and buy something, we get a small commission at no cost to you. This helps us keep this blog going so we can continue to provide you with van build tips, tricks, and guides. We believe in honest opinions, and we never recommend anything we don't know about. Every recommended product on this page we've either used personally, have personal experience with, or have researched heavily.
Couldn’t disagree more. Still got the same setup a few years in. As mentioned the sag is minimal (not non-existent), I place a small removable 2×2 near the tailgate so I can hop up top. You’re not building a home up to code, you’re building a practical truck camping solution, and in my extensive experience it is more than fine. You can do thicker plywood, but realize that it will be much heavier and more cumbersome to move.
I used to coat my metal table saw and planer bed with auto wax because it makes the wood slide nicely across the metal. But then I saw an expert cabinetmaker use wax paper, and now I do the same. I keep a roll in my shop drawer and rub a sheet of it over the metal beds on my table saw, router, planer and disc sander. The wax coating doesn’t last as long as a good paste wax, but boy, is it a lot easier and quicker. — R.J. Hayes. Plus: 22 clever new uses for your tools.
We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.
Now, some of the things we’ll be covering in this week’s show will be things that you can use around your house whether you’re an avid woodworker or not. We’re going to talk about a little fold-down workbench that’s perfect for maybe that little area you have in your garage or your storage building. Also the importance of building the proper surface to work on, lighting, dust collection, a number of other things I know that you can use, but I’m so anxious to get this stuff out of here. Within the area like this whether it’s in a business or home there’s plenty of stuff that just needs to go away. But there’s also some tough to decisions to make about what to throw away, what to keep and how to organize what you hang on to.

Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
As a carpenter, I need to bring certain items with me every day. I bought a cheap plastic tote in the tool storage area at a home center and modified it for my needs. I made a small plywood deck, drilled a couple of 3-in. holes for coffee cups or glue bottles and then fastened it to the tote. Another piece of plywood has holes to keep pencils upright and organized. My tote sits nicely on my bench seat, but it could also be attached to the floor with hook-and-loop fasteners. You could easily customize these totes for plumbing, garden or painting tools, electrical supplies—what have you. — Don Simms. Check out this jumbo tote for fasteners.

I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
You’ve probably considered what goods and services you’ll be offering, but have you researched the cost of sourcing your raw materials? How about the cost of turning those raw materials into your finished product? Do you understand how much you’ll need to charge for your products/services in order to cover the expenses of renting a space, paying employees, leasing equipment, and paying for permits and regulations? Moreover, have you considered if the answers to these questions will provide the kind of operating margin you’ll need to pay yourself a salary?
When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
There are a number of woodworking fixtures you can get by without for a long while, but a sturdy workbench isn't one of them. The trouble is, those solid-hardwood benches we all lust after can completely blow a modest woodworking budget. Here's a bench that splits the difference. You'll get a top that can stand up to significant abuse, a sturdy, heavy base that keeps the bench planted where you put it, and an end vise and T-track system for holding workpieces as well as a variety of unique jigs. It may not look quite like a European bench, but it works just as hard as one for a lot less money.

Hey! Thanks for stopping by and checking this out, I appreciate your comments as well. It is something I really should do… I’ve done a bit more research on this since I initially posted it, and it is less intimidating the more I read. It just comes down to actually doing it and spending some more money, I guess. I’ve got the 22RE in my truck… I still need to look more into the alternator aspect though.


Nice video Marc. I did enjoy seeing the details of the construction process. Since becoming a homeowner and a woodworker (something that happened literally at the same time) I have become fascinated with anything having to do with the process of building and finishing and all the details in between. I thought of an off the wall question while watching this video and that is do you write yourself any kind of script for any of your monologues and/or narrating or do you just have a general idea of what you want to say and wing it?
While we were painting all of the walls in our workshop our plumber dropped by to hook up an old laundry tub sink that we’ve had for several years. Now, he hooked up to the cold water line on an outside water faucet, so we’ll only have cold water but still this will be really convenient to have this right here in this shop. Well we’re about to set our last base cabinet, and once they secure that well to the wall we can start on all of our countertops.

Budget Toilet: Luggable Loo. With the Luggable Loo from Reliance Products, you can turn any 5-gallon bucket into a portable toilet for your van. Make sure to line your bucket with a trash bag or toilet waste bag - then once you’ve done your “doodie” just tie up the bag and dump it in the trash. Reliance also sells deodorant chemicals that will make it easier to live with your new roommate


With the third category, franchise businesses , the risk of getting started is potentially the lowest of all when it comes to starting a small business, as you are often buying into a clearly established business model. You will also often benefit from the initial support of the franchisor, including advice around site selection, training and orientation, employee hiring, and product mix coordination. This support and assurance, however, comes at a premium. On top of the normal startup costs (space, equipment, etc...), you’ll have to pay a franchise fee to the owner, which is often tens of thousands of dollars, as well as a percentage of your revenues on an ongoing basis.
High-velocity fans are also an important tool in their own right, particularly at your finishing station. Increased air flow will help dissipate fumes from paints and sprays for your safety, and you can train a fan on your project to help paint dry more quickly between coats on humid days. To get the most out of your fan, look for floor fans that are easy to aim or wall-mounted fans that will save space in smaller shops.
I don’t have recs because I’ve always just gone the traditional cold weather camping route with warm clothes, winter sleeping bag, boiled water in a nalgene, shot of olive oil before bed, etc, etc. Perhaps someone else might chime in… I’ve heard of folks (with the appropriate dual battery setup) using electric blankets, or yeah, the Mr. Propane heater (but not while they are asleep).
What I have done in my man cave of a shop is to install above my finishing table a strip of track lighting where I have fixtures ranging from the typical bright white incandescent (typically around 4700k) all the way to the average halogen spot that I figure someone would use with an art piece (normally around 3700K). this allows me to point each light and view my piece and finish under varying light conditions to judge whether or not I prefer a particular finish or not. It also helps in photographing items (though filming is a whole nother story, I still have my 5400k T8 overheads for working).
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
Using six pipe cleaners, you can make your own skeleton. Bend one pipe cleaner into two for the backbone. Twist another around the bottom of the backbone to make into the legs. Do the same for the arms. Join two pipe cleaners and twist them around the backbone leaving some space forming a ribcage. Ultimate Small Shop Woodworking Twist the last pipe cleaner for a head and glue on some eyes. Hang with a rubber band for a bouncing effect. Your kids will love making Halloween crafts with pipe cleaners. But be careful when cutting and keep them out of their mouth. Going trick or treating? Why not make a special jug to collect candies? Cut off the top two inches of a gallon milk jug. Soak to remove any labels. Paint orange. Once dry, paint or stick on eyes nose and mouth resembling a Jack O’Lantern. Use fluorescent paint for a nice effect. The jug can be kept for future reuse. Using glue and food coloring, you can make a see-through painting. Paint a Halloween image onto a piece of plastic wrap. Before the mixture dries, put another piece of plastic wrap on. Cut it out and hang it in front of a light source for a see-through effect. You could also frame the plastic pictures using wood or cardboard if you want them to be longer lasting. Make some hand printed spiders. Ralph Chapman Ultimate Small Shop Apply black paint to your palm and 4 fingers leaving out the thumb. Place palm onto a piece of paper. Turn the paper 180 degrees and print again making sure the palm overlaps. Add some wiggly eyes using either paint or sticks. This is suitable for even 2 or 3-year-olds. Make your own blood. It is less expensive than buying ready-made blood from the Halloween shops. It’s not difficult; all you need is Karo syrup and food coloring. While you’re at it, why not make some slime using glue, water, and borax powder. This is an advanced Halloween craft, so take your time and be careful. Using apples, you can make dried, shrunken heads. Peel the apples and coat with a mixture of lemon juice and salt to prevent browning. Carve out a face of eyes, nose, and mouth. Do not worry about the finer details as they will probably be lost when the apple dries. You can use whole cloves for the eyes and rice grains for the teeth. Let the apples sit out in a warm place for about 2 weeks. If you don’t have 2 weeks, you can speed up the drying by putting them into an oven on the lowest temperature for about 45 minutes and then dry out naturally for the next 2 days or so. Ultimate Small Garage Clock Shop Once dried, they shrink and deform into weird and scary looking faces. Says Angie Maroevich, “You don’t have to spend a fortune on commercial Halloween supplies to have a great party.

Hey Melody, thanks for the email. I’ve traveled through some extremely humid areas (Central America)… I’m taking it that your canopy does not have a headliner? That in and of itself helps a great deal. Personally I would be hesitant to put holes or van roof vents in my cap, but that may be what you want to do. I would try sleeping with a portable personal fan first and see how that helps with the condensation issue. For me it worked wonders while sleeping in those hot and humid environments. I ran mine off the inverter connected to my secondary battery.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
GoWesty, a well-known Vanagon restorer and parts maker, recommends not buying a Westy unless you have at least $25,000 to spend overhauling it and replacing aging components. Even if you find a cheap Westy hiding out in a garage somewhere, be prepared for frequent breakdowns and expensive mechanical headaches unless you spend the cash to fully rebuild it.
There are a variety of structures to choose from when starting a small business. However, the most common business structures include sole proprietorship, partnership, corporation, and S corporation. The structure you choose determines which income tax return form you have to file, which, you guessed it, dictates your legal and financial responsibilities as a small business owner. Because of this, you’ll want to make sure you understand the options that are available to you and weigh the pros and cons before incorporating your business.

Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
Sometimes you just know it when you see it. So always be prepared to capture pictures and take notes when you see store features that you’d like to try out yourself. And don’t forget the many online resources out there. Settle down with a cup of coffee and scroll through Pinterest for a treasure trove of store design ideas. Here’s a great board to get you started. Or get inspired by the many hip retail store designs on the Retail Design Blog.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.

This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obsta­cle such as a setback.
So you stayed up all night, thought long and hard, and decided you want to name your designer sunglass hut The Sunny Rabbit. We don’t blame you, it’s a pretty cool name. Most would tell you that the next and most logical next step is to register your business as a DBA or at the state level. But, we’re here to tell you that’s wrong! Here’s why. We just talked about how the right business name can make or break your brand identity and in today’s digitally connected world, securing your brand identity across the web is equally as important.
​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.
Hey Joe, I just hit 178k on my truck. I remember when I started out the first time around it had like 144k or so. They are known to go quite far, so we’ll see how it goes. Maintenance on the road… I just stop at those oil lube places for the most part, and do regular weekly checks under the hood for fluid levels, etc. I’m not too mechanically inclined!
The kind of apps that fall into this app type are extensive. Facebook, Instagram, Snapchat, Twitter, WhatsApp, Pinterest, and YouTube are all examples. Remember that some of these apps have been worked on for many, many years. Thus, a v1.0 social app or social networking app will likely not offer all of the same features. For instance, Snapchat did not start with videos, filters, or their "Stories" functionality. A social app would, however, include user authentication, friending, favoriting (or other data interaction), some sort of messaging, and comparable "baseline" functionality.
The idea of not having your own bathroom nearby can be incredibly intimidating, but we’ve found that this is actually one of the easiest parts of vanlife. Public restrooms are plentiful throughout North America, and we’ve never not had a bathroom when we needed one. Gas stations, truck stops, Walmarts, McDonald’s - you name it, we’ve done some business there.

A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
We're living in an age where we can order groceries, turn on the lights in our house, or get in a workout from the convenience of our phones, tablets, or other devices. Apps are a part of our everyday lives. They are increasingly giving us more free time or vying for more of our attention, depending on how we choose to use them. With that, here are some of the more important changes since we published our app cost article in 2015.

However, another critical component to small business success is being self aware. With a variety of tools at your fingertips, tracking basic accounting can be fairly simple. Still, in order to be strategic about how you spend your money, properly leveraging these tools will still require a little bit of legwork. What used to take you eight hours might now only take one hour. But if you’re not willing or able to run through your financial tasks on a regular basis, bringing in a bookkeeper or accountant might be your best option.
Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.

We’ve been focused on the first category so far, but there is also an allure to buying an existing business. These enterprises will often come with brand awareness, a customer base, trained employees, an established supply chain, and most importantly (we hope), demonstrated profitability. As a result, countless startup risks can be diminished by taking this route. That is only true, however, if you make sure to carry out thorough due diligence on the existing business.


You can also make your store comfortable by incorporating a waiting area with comfy seats and benches to encourage customers to spend more time in your store. This is especially helpful for shoppers accompanied by someone who isn't interested in making a purchase. But keep the seats or benches facing the merchandise so that they're still top of mind for those lounging around in your store.  
A warning out of concern and love for my fellow 'ablers. A framing nailer is a VERY dangerous tool. Not something to loan out willy-nilly to just anybody. For a small project like this it's just not going to save a lot of time. Most of us are better off burning the extra calories that swinging a hammer uses anyhow. Emergency rooms are seeing a lot of visits because a lot of guys see these on TV and at your big box stores and think they look cool. They are only marginally safer than shooting at the nails with a pistol. (Hmmm...). Be careful, PLEASE.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
We have LED puck lights in our van. Puck lights are typically recessed into the ceiling, so they have a very clean look that’s really integrated with your van. It’s also easy to create different lighting zones by running your lights off different switches. We have six puck lights in the main living area that are controlled by one switch, and two more over the bed that run off a separate switch.

Spacious pathways are a key aspect of good store planning. In fact, it tops the list of retail experts’ store design tips. Heshy Lovi, Sales and Marketing Director for M Fried Fixtures, recommends aisle widths of four feet or more. This, he says, ensures your aisles and pathways will be comfortable for all customers, including those using strollers or wheelchairs.
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
I used to coat my metal table saw and planer bed with auto wax because it makes the wood slide nicely across the metal. But then I saw an expert cabinetmaker use wax paper, and now I do the same. I keep a roll in my shop drawer and rub a sheet of it over the metal beds on my table saw, router, planer and disc sander. The wax coating doesn’t last as long as a good paste wax, but boy, is it a lot easier and quicker. — R.J. Hayes. Plus: 22 clever new uses for your tools.

When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.

We have LED puck lights in our van. Puck lights are typically recessed into the ceiling, so they have a very clean look that’s really integrated with your van. It’s also easy to create different lighting zones by running your lights off different switches. We have six puck lights in the main living area that are controlled by one switch, and two more over the bed that run off a separate switch.
Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
Impulse items like small toys, candy bars, lip gloss, and breath mints are great products to feature near your register. When customers approach the register to pay and leave, you don’t want them to stop shopping. Placing low-cost impulse buy items near registers, as shown in the image below, encourages shoppers to add an item or two as they check out.
We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.
×