Once I had the walls completely filled in and trimmed out, I built my doors.  I clamped them in place each day until after I painted.  Then I installed the hinges and hardware.  I decided to change my original plan of building a hinged 4 foot door.  I was worried that the weight of it would cause it to sag over time.  I had also decided at this point to install a small unused AC in the back wall.  I thought that by keeping one of the doors closed, I could keep more cold air in during the hot summers.

​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.


You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.

Listing agents are hired by a landlord to list their commercial property. Listing agents earn a commission that’s paid by the landlord, typically between 3% – 6% of the total lease. Tenant brokers, on the other hand, represent tenant interests. However, tenant brokers also typically earn a percentage of the overall commission paid by the landlord, knows as the tenant broker’s fee.
I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.
Can you outfit your shop with all the necessary hand tools for just $100? Christopher Schwarz says you can, and he’ll show you how to do it in this article. Take Christopher’s shopping list to the flea market and come back with everything you need for less than you’d spend on one new hand plane. You can do all your woodworking with hand tools, and this article from Popular Woodworking will equip you with everything you need.
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood dur­ing a glue-up.
You can see I broke the ultimate goal down into smaller tasks. Now you just need to do this for all the big goals that you have mapped out for the year. You may have more ideas or goals throughout the year and that’s okay. With this type of document, you are able to add another category and tasks anytime you want. This is just the best way to keep track of all the little things you need to do to accomplish your goals so you never are stuck wondering what you have to do next.
I have a basement shop with a walk out and a seperate entrace to my shop.I have approx. 5oo sq feet to work in there, there is natural light that comes in with a graet view of the lake that we live on.I have started to dress up my shop after making such beautiful furnisher for other people it started with a bench witch is 11 ft, long and plenty of stoarage space under the bench , the low storage aera of the bench is made from black walnut and the bench top is oak with bubinga trim. Saw cabient is white oak ,miter saw cabient is walnut ,american chestnut ,cherry and maple. Now the joint cabient looks out of place so I will be making a better looking cabient for the 6in. jointer. I had made a plant self to start plants along the widows but took it out and put a bench top there so it looks as a big window sill but I use it for a place to set tools as I am working on the bench also I have put walnut around the widows and painted the walls.There is a 10in. powermatic table saw,powermatic drill press fl.modle,rockler 6in. jionter, mekeita compond saw,delta 14in band saw, I have two planers and a table mount router in my bench top ,also there is an old american lath witch I have in stoage and a sears jig saw.
This holds a lot of stuff but mainly our handheld power tools, so it needs to support a lot of weight. Any shelf in a workshop will probably wind up supporting more than you initially planned so build it as strong as you can and don’t scrimp on the materials or the fasteners you use to hang it. Now the next step is to install our recycled cabinets that will line the wall under the shelf. Now these cabinets are a little plain but that should work great for a shop like this. Even if you don’t own a remodeling company you can usually find these things pretty inexpensively from salvaged warehouses which recover them from renovation projects then resell them to the public.
Leslie recommends that retailers provide some type of seating for both customers and anyone who is accompanying them. Shoppers do get tired and so do their friends and relatives who are along for the ride. Why not offer them a chair? Seating can be as simple as stools near the checkout or a lounge area near the dressing rooms, like this fun setup below:
In many ways, skoolies are the ultimate in mobile living. The big advantage here is space - there’s tons of room for couches, beds - even a full bathroom - and you can easily accommodate families and other larger groups. There are also some really impressive skoolie builds out there that are nicer than actual houses, and it’s a whole lot cheaper to convert a bus than to buy a similar-sized RV. Skoolies come in multiple sizes, from “shorties” to full-sized buses.
In the case of this guide we’re going to use an area that’s a little larger and show you the tools you’ll need to set up a small workshop in just a 10×8′ shed. The list of tools is generally considered enough to cover the most common tasks. Everyone will have their own opinion on this and naturally it depends on the work you’re carrying out. But the tools on the list should be enough to strike a productive balance between having enough to get the job done and not being caught short so you’re having to borrow a friend’s. Invariably people grow their collection of tools as the jobs dictate. You don’t necessarily have to buy everything at once, just build up your list as you need to.
I spent so much time building organizers and filling in just about every square inch on the inside of my shop that I feel it will be better to show some of those in separate Instructables.  I made a couple of video tours to try to highlight some of the different aspects of my workshop.  I hope you enjoy them and I will work on making my future videos more stable.
Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for bill­ing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.

The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.


Both kids and adults have sat inside [the Optimus Prime truck] and been brought to tears. For many, it is a dream come true. Some kids are very intimidated by Optimus Prime because of the size and won’t go anywhere near it. But I love making people smile. The fact that I can make them smile for just a few minutes by seeing Optimus Prime on the highway means the world to me.
If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”
Congratulations on your new shop and all your success. I’ve watched all of your videos and someday if I have the money I would love to join your guild. I started a small workshop in my grandparents basement and someday I hope to start a small bussiness. Your website and videos have been the most informative and the most inspirational to me as a beginning woodworker. Thank you for sharing all your tips and hard work with people like me. I look forward to watching your videos for years to come.
Location, location, location is quoted so often for a reason. When starting a small business, the wrong choice could hurt your business before you’ve even had the chance to open the doors. Take the time to really understand your customers and do everything you can to gather real world insights that will help you determine the viability of your potential new space.
Many small businesses in New York and New Jersey were forced to close following Superstorm Sandy because they lacked the insurance that would have gotten them back on their feet. That part is well known. What’s less well known is that this lack of proper insurance, coupled with the lack proper legal incorporation, resulted in many entrepreneurs seeing their personal assets come under threat.

Small business owners can maintain steady, manageable growth by keeping a firm eye on costs and always aggressively looking for ways to increase sales and grow their brand. It can be difficult to empower staff and managers around you, especially if you’ve spent a long time steering the ship alone, but it is an essential part of successful expansion. Stay open to suggestions from your managers while making your current business best practices clear to them.
The nomadic truck camping lifestyle has been incredibly freeing, not only is cheap and accessible to most anyone, but it can take you beyond places you even imagined. One book that I’d recommend to all newcomers to this lifestyle is Bob Wells’ How to Live in a Car, Van, or RV, which will help you better understand the ins and outs of this lifestyle.
×