What I have done in my man cave of a shop is to install above my finishing table a strip of track lighting where I have fixtures ranging from the typical bright white incandescent (typically around 4700k) all the way to the average halogen spot that I figure someone would use with an art piece (normally around 3700K). this allows me to point each light and view my piece and finish under varying light conditions to judge whether or not I prefer a particular finish or not. It also helps in photographing items (though filming is a whole nother story, I still have my 5400k T8 overheads for working).
If you’re moving into a space that requires renovations in order to fit your business needs, you’ll also want the landlord to take on responsibility for that work. We’re not talking aesthetics here, we mean necessary renovations such as improved data connectivity. If you have to do the work yourself, it’s advisable to ask the landlord for a rent-free or reduced-rent period. You should also make sure that any additional alterations you have in mind are acceptable and would not be in breach of the lease. Last but not least, always make sure the do’s and don’t of what can and cannot be done is put in writing, it will save you a lot of headaches later.
Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.
Many DIY campervans have kitchen units that are directly behind the cab, sealing it off from the rest of the van. These layouts offer increased privacy and stealthiness, especially if you completely wall off the cab, and open up some space in the back of the van. This layout can be paired with a lengthwise bed, fixed bed, or convertible dinette bed. You can also place your propane and water connections right by the door, making refill easier.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”
One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks! 

Great instructional! I built the bed of my 92′ Toyota pickup ext. cab the same way you did. I did some hard searching and found this camp pad, which literally fits the 40″ wide sleeping space perfectly. A few different mats from Exped will fit, but here’s the one I bought. Just thought you might like to know there’s an inflatable duo sleeping pad out there that works for your setup!
In an indoor or basement shop with industrial carpeting, lay down inexpensive laminate flooring to make your life a bit easier at the end of the day. Be sure to anchor the panels or place a large rubber mat beneath to keep them from sliding over the carpet. (Covering up your carpet is even more critical if you want to go beyond wood and work with a material such as aluminum in your indoor shop; metal shavings dig into any kind of carpeting and are incredibly frustrating to clean up.)
I don’t think you have run into this problem, but I have to deal with condensation in the cap as I live in a moist climate. I was thinking of an old van type roof vent with fan for active ventilation, or drilling holes along the side of the cap, inserting short cuts of pipe with fine screens (mozie land), and capping them. This way I could control for rain, cold, etc., but create some passive cross ventilation at roof level.
Once you know your top priorities, you can start thinking about the space each element can take up and where it should go. It is like putting the pieces of a puzzle together when you're working with a small space, so don't get frustrated if it doesn't work out right away. And know that you'll likely have to make some sacrifices. Play with a few options, and choose the one that works best for your situation.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
For now we’re just getting it out of the room so that our electrician can get started. In any kind of workshop you want plenty of access to power and lots of use of the light. So Mike our electrician is hooking us up. If a service call from an electrician isn’t in your budget you can plan your space so that you can best take advantage of the outlets that are already there. Now Mike has checked all of these surfaces to be sure they can handle these extra outlets he’s adding.
Ultimate Small Shop is a complete guide to setting up your own workshop, from the planning phase to optimizing it for business. You’ll learn how to put together a complete and functional workshop for less than you expect. Ralph aims to get your shop set up for less than $1,000. Ultimate small Shop includes suggestions on where you can get the tools and equipment needed at the most affordable prices and how to optimize space to get the most out of the little room you have.
Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.
The dream of a dedicated home shop is a common one among woodworkers. Whether you currently borrow shop space, work in your driveway or side yard, or compete for a corner of your basement with Christmas decorations or your fur­nace, you may be ready to build your own space that will allow you the free­dom of more room and time, and will also keep dust, fumes, and noise under control. Every design/build situation will be unique but there are a series of consid­erations that you will face in the design and construction phases of your project. Let’s walk through the process and dis­cuss the questions that you will need to ask yourself and others as you approach this project.
The primary investment of any garage workshop are the tools. Protect your investment with a high quality tool chest that is neatly organized and (if needed) lockable. Look for smooth rolling ball-bearing drawers, and if you’re buying used, beware of rust and dirt that could corrode your tools. We recommend installing drawer mats to keep your tools from sliding around. They also give your tools a softer cushion to rest in.
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie
Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.

As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.
James Hamilton (or “Stumpy Nubs”) is a self-taught tool expert, engineer, writer, teacher and video producer. In 2008 he went into woodworking full time, creating a weekly Internet woodworking show that focused on the workshop itself. Now, Stumpy Nubs Woodworking has grown into one of the most popular multi-media woodworking resources in the industry.
A warning out of concern and love for my fellow 'ablers. A framing nailer is a VERY dangerous tool. Not something to loan out willy-nilly to just anybody. For a small project like this it's just not going to save a lot of time. Most of us are better off burning the extra calories that swinging a hammer uses anyhow. Emergency rooms are seeing a lot of visits because a lot of guys see these on TV and at your big box stores and think they look cool. They are only marginally safer than shooting at the nails with a pistol. (Hmmm...). Be careful, PLEASE.
One site that I found a year or more ago was Life Remotely. They converted their truck to accomodate 3 people traveling from Seatle to the end of South America. They camped in tents most nights and some hotels/hostels but did a lot of conversions to their truck. Plus they blogged the whole time which is pretty cool if you want to take the road trip international.
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​

Many retail fixture and display companies provide store planning and design services to their customers. Though typically not free, these in-house design services can be far less expensive than hiring an independent designer. Plus, they can help streamline the process of store layout and planning, along with the purchasing and installation of displays and fixtures.
Workers’ compensation insurance is designed to provide wage replacement and medical and death benefits to employees who are injured or worse on the job. In exchange for these benefits, the employee gives up his or her rights to sue for liability leading to the accident. Your premium will reflect the type of business you operate and the average salary of your employees. Much like auto insurance, business owners who are new to starting a small business or those with less experience tend to pay higher premiums.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
They say nobody ever started a small business out of a love for numbers, but if you really want to stay the course, you’re going to want to fall in love fast. It’s only by keeping detailed accounts and tracking your business’ numbers over time, (net sales, cost of goods sold, and average transaction size) that you’ll start to gather the actionable insights you need to make intelligent business decisions.

It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
Like most things in life, we believe that entrepreneurship can be learned, you just have to be willing to put one foot in front of the other. Aftering reading How to Start a Small Business 101, you’ll be equipped with the essential tools and resources you need to succeed at planning, raising capital, and executing crucial day-to-day business operations.
At least once a year I want you to set aside some time (I’m talking about a large chunk of time - like a day) and I want you to write down everything you want to accomplish this year or next year (or whenever you are planning for). I tend to plan for a whole year, but you can try 3-6 months to help you get started. Take away any and all distractions because it’s important that you are super focused on what you want to accomplish for the year. This is the time to let your ideas flow, don’t hold back. Things on this list can include: Launch your own website, release a new invitation line, and work on my Instagram account. Don’t overthink, just write down what comes to your mind and whatever your heart desires. There will be time later to refine what you have written down. When you are starting to brainstorm your goals, I would suggest that you first start off writing them on a notepad like this. And then once you are done, you can move them over to a task organizer like this.

Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.
×