Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.

Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D mod­elling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experi­ment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you antici­pate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.


Other than that, you can’t have too much light — especially north light! — and you want accommodations for all the electricity you can imagine. Ceiling fans are a must. A good dust collection system is good, too. Don’t forget to plumb in for compressed air. Do NOT use hard PVC water pipe for compressed air — ever. If/when it breaks or ruptures, it explodes into tiny sharp glass-like shards. I know firsthand. I’ll tell you about it some other time. Think balloon popping!
When you are looking for small business funding options, be it from the local bank, an angel investor, or even a family member, the first thing you will be asked to present after your business plan will be any existing financial records. Make sure you are putting your best foot forward by keeping meticulous records, with your business finances completely separate from your personal finances.
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
A not for compensation nonexclusive arrangement, on the other hand, gives a tenant maximum flexibility. It’s nonbinding and there are no commissions negotiated. Instead, it gives the broker the right to speak on your behalf and schedule listings for you to see. However, while it provides flexibility, this arrangement gives the tenant broker less of a fiduciary duty.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
A not for compensation nonexclusive arrangement, on the other hand, gives a tenant maximum flexibility. It’s nonbinding and there are no commissions negotiated. Instead, it gives the broker the right to speak on your behalf and schedule listings for you to see. However, while it provides flexibility, this arrangement gives the tenant broker less of a fiduciary duty.
Really enjoyed watching the video of the shop build. You will be turning out great pieces in no time. At the end of the video it looks like you have your dust collection system up and running. Where did you purchase the duct work? I thought I remember you talking about this in the old shop. Did you use regular HVAC 4″ round duct or a heavier piece. Thanks for the insight and good woodworking.

The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.

Ultimate Small Shop offers a comprehensive guide illustrating how to set up a workshop. It may be just a small basement shop or a part of the garage converted into a workshop. The guide lays out all the steps and actually caps the investment at under a thousand dollars. Woodworkers can build their workshop for less than $1,000. This does not entail any compromise of tools or the scope of woodworking projects. The guide provides a shopping list including the best tools and there are exact links to find those tools and buy them at the best prices. There are floor plans to ensure layouts are optimized even in the most cramped spaces.
Chances are if you’re starting a new small business, you’re not afraid of a little risk. However, it’s also highly likely that you have invested a large amount of money in this new endeavor. It is only prudent to take sensible steps to minimize the impact of unexpected events, like the untimely death of a business partner, a lawsuit from a customer or employee, or a freak accident of nature.
This OXO palm brush really helps us conserve water while washing our dishes. We fill the reservoir with water and a few drops of Campsuds, and we only squeeze out what we need - so it takes care of both the initial rinse and getting our dishes soapy with minimal water usage. It’s also very compact, and the comfortable shape makes it easy to scrub dishes.
Hi Ryan: Nice job on the truck. I also have ’94 Toya 4×4 coffin sleep setup. Looking to change (access cab wanted) and may use some of your ideas. One thing I didn’t see you mention is ventilation. I am from the Mid-Atlantic region(DC/Maryland, you’re old stomping grounds) and ventilation at the New is important. My side windows have screens and I use an old mesh fly with a flexible pole for the rear tailgate area. It works really well. Kinda jerry rigged but is easy to put up and take down as well as pass through for nighttime truck exits. Not needed out west as much since bugs and humidity are lower but can’t live w/out it in these parts.
Plus, taking the time to put pen to paper should benefit you as the small business owner as much as any potential new employee. Creating this kind of central resource about best operating practices will force yourself to formulate your thoughts and be clear about exactly what you want. Whether that means codifying sales procedures or deciding who can take cash from the cash drawer, you’ll have a clear and consistent company policy, something to which most employees will respond favorably.
Tired of the rat race, I opted for early retirement. Looking for something to do with all my free time, Ultimate Small Shop Ebook Free I started crafting and am now making a nice supplemental income from it. As a crafter and a businesswoman, I feel I have some valuable insights into the craft business that I can share with you. At some point in your progression from crafting for fun to crafting for fun and profit, you go from handcrafting individual items for yourself and friends to filling quantity orders for a broader marketplace. That’s the time to take a very business-like approach to your craft business. This needn’t be daunting. You don’t need an MBA or management experience – just a bit of common sense. If you’re going to do this for profit, you need to understand Simple, right? But very few people get it. Look at the high failure rate for new businesses. It takes an effort to be successful, but the task is hardly impossible. Traditional craft retailing methods are what most crafters use to get started. They’re the easiest way, especially if you don’t know if anyone will buy what you make. I believe that there is a market for any well-made craft, whether decorative or useful. The problem facing many crafters is how exactly to go about selling them, or more accurately, finding paying customers. The fact is that there is an awful lot of competition out there. My own business got jump-started by my “circle of friends”. Ultimate Small Shop Free My friends noticed and liked my calling cards and began to ask me to design and make cards for them. Starting with just Broderbund’s Create-a-Card program, I was soon earning a nice supplemental income in just a few hours a week. It probably helped that I was retired and live in an area dominated by retirees. But I think that everyone has a “circle of friends” either socially or at work. Of course, you don’t want to impose on their friendship by making a hard sell, but rather use or display your crafts in front of your friends to see if they draw any interest. If they do and if they’re priced right, you’re on your way to craft retailing for profit. If your “circle of friends” market starts extending to friends of friends, you’re probably ready to tap the general marketplace of craft retailing. Most crafters are aware of the periodic craft shows put on by local groups or even by the local Parks Departments. These usually cost little or nothing to join and should give you a fair idea of whether there is any broader interest in your craft. What better way to jump into craft retailing? There are also organized craft shows that tour the country, Ultimate Small Shop Legit most of which charge an entrance fee for participants.
It can become very difficult and time-consuming to constantly track the amount and purchase price of all your inventory, but it is hugely important to your bottom line. Every time you catch yourself saying, “Sorry, we don’t have that in right now,” you are leading your business in a very unhealthy direction. Not only does being out of something represent a lost sale opportunity, but in a world where consumers place a huge premium on their time, it could mean that you lose that customer forever while hurting your brand reputation in the process.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
After years of digging through piles of stuff on my workbench for the air compressor accessory I needed, I had this idea. I simply drilled 7/16- in. holes on the underside of my workbench top and threaded in a few 1/4-in. NPT male couplings with quick-connect couplers. A wrench and some upward pressure are all it took to screw the couplings into the wood. Now I just snap my accessories onto the couplers when I’m not using them. — Donnie Dressler. These are the best tools for automotive work.

This is where I started thinking about how I was going to store all of my lumber.  I had planned on building a wall rack, similar to what I had used in my single car garage.  But I hated using up an entire wall for lumber storage.  I also knew from experience that I would easily lay stuff against it and soon be digging lumber and junk out of my way.  I decided to use the space under my workbench to store the long boards and I realized that by pulling my bench out from the wall I could slide sheet goods behind it.  This created a problem:  How do I get it out.  The Shop isn't long enough to pull out 8 foot boards from inside and I would probably have to move things around to get to it anyway.  So my plan for this came at kind of a sudden epiphany moment, when I decided to cut access doors in the front and build my storage into my workbench area.  This has been the single best idea that has come out of my shop.  I can't express enough how easy it is for me to get straight to a board i need with no hassles.  I just remove the doors and pull out what I need.  I can store a surprising amount of lumber in this area.  I do have a secondary area for some cutoff sheet goods and a scrap bin next to my table saw in the garage.  But this area stores most of my lumber.

​In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts.  Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up.  A more economical approach would be to build your jigs as your projects demand them.  After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.


If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
I decided to do Optimus for many reasons. One big one was that no one else in the world had done it. There are tons of Bumblebee Camaros and other replica cars, but no other fan of Transformers has replicated the T4 (fourth Transformers movie) and T5 (fifth Transformers movie) Optimus trucks. So if I am to show my son through action what it means not to be afraid to take a chance, I figured Optimus was the best way to try.
While an electric miter saw is a convenience, it is not necessary to do good work.  A quality electric miter saw will run around $150-$200, that by itself would destroy our budget.  A hand saw with a miter box does the job just as well at a fraction of the price.  This highly rated Stanley version for ~$60 should get the job done, albeit with a bit more elbow grease.

Many DIY campervans have kitchen units that are directly behind the cab, sealing it off from the rest of the van. These layouts offer increased privacy and stealthiness, especially if you completely wall off the cab, and open up some space in the back of the van. This layout can be paired with a lengthwise bed, fixed bed, or convertible dinette bed. You can also place your propane and water connections right by the door, making refill easier.
Marc, I enjoyed the video. Thank you for sharing your dream shop with us. I would be interested in seeing a demo video on your Clear Vue cyclone dust collection system. Which one did you obtain & what type of duct work did you use (seamless?) Do you plan on enclosing the unit in a closet to reduce noise and keep dust confined? Do you have to purchase special expensive plastic dust bags for the drum? Is it hard to pull the bag out of the drum for trash collection? If you could address these questions in a demo video I would appreciate it. Oh, perhaps you already have one …. I will check out your video archives. Thanks again and keep up the great work!
Conversion vans have some pretty sweet built-in amenities, including high-tops for extra headroom. Many have comfy captain chairs, leather seats, mood lighting, TV/VCR, and a rear bench seat that folds down into a bed. If you’re not picky about your living situation, this could be all you need to get started. And if you gut it and customize it yourself, the high top offers tons of great storage options that other vans just don’t have.
Congratulations on your new shop and all your success. I’ve watched all of your videos and someday if I have the money I would love to join your guild. I started a small workshop in my grandparents basement and someday I hope to start a small bussiness. Your website and videos have been the most informative and the most inspirational to me as a beginning woodworker. Thank you for sharing all your tips and hard work with people like me. I look forward to watching your videos for years to come.
When you set out to start your small business, investing in the right technology and equipment should be considered in conjunction with your store design. They should seamlessly integrate with and improve the customer experience in your store. Everyone remembers their first trip to the Apple Store and the “wow” moment of having their sale rung up by the assistant in the middle of the store, rather than having to wait in a line. But fewer people probably notice the carefully positioned heater that creates a warm environment for them as they walk through the door. It’s all part of the same idea.
Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.

I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
Without organization, living in a van can feel cluttered and chaotic, so you'll want to make the most of your storage space. This is a good time to make sure you've paired down your belongings to a reasonable amount and to make sure everything has a place. (As a former engineer who loves making things as efficient and optimized as possible, this was Ben's favorite step!) 
To help, I’ve pulled together 40 small business ideas for anyone who wants to run their own business. Use these as a jumping off point to spark your own unique ideas.And if all else fails, live the words of Airbnb Co-founder Brian Chesky: “If we tried to think of a good idea, we wouldn’t have been able to think of a good idea. You just have to find the solution for a problem in your own life.”

Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.


In a small space, there's not much room for one-trick ponies: You need gear that can do many different things, and that goes for your work space and stands, too. You can add a wood clamp to a multifunction workbench, but you probably need compact work or tool-holding stands to make up for the lack of a large work surface. Occasionally you may need to take your work to another room or even outside, in which case portability is also important.
I think it would work pretty well for a music festival, I don’t see why not. I wouldn’t say it is robbery proof, but generally robbers are looking for quick and easy targets, like a purse sitting on the front seat, just smash and grab. If someone really wanted to rob what was under they platform, they surely could, but they’d need more tools and more time to do so. And they don’t even know if there is anything good under there… I’d like to think of it as a really good robbery deterrent.
In our opinion, the best kind of fridge you can get for a DIY campervan is a portable 12V fridge/freezer. These fridges are built for adventuring on 4x4 vehicles and boats. They’re very rugged, and they don’t need to be kept perfectly level like mini-fridges. They can run off 12V power or regular 110V. They keep your food as cold as you want, and they can operate as either a fridge or a freezer.
I live in Northern Va and have the same concerns. I save those little silica gel packets every time they come in a new product and put them in my tool drawers. I also salvaged a dehumidifier from a neighbor that I need to repair and set up in there. I use the wall mounted AC in the summer to keep it cool enough to work in there. Although I haven't gone back yet to insulate the ceiling, it stays really cool in there if i want it to be.
Calculating the size of your desired parking lot is easy. The rule of thumb is to have a parking spot for every three customers. Determining traffic is trickier and potentially more lucrative. To help, we wrote an article on how to calculate your desired foot traffic. If you want to calculate your desired vehicle traffic, you can refer to our article on how to choose a location for your restaurant.

Living on the road puts you in a wider variety of situations and environments than being stationary. If something goes wrong in the wilderness or if a disaster strikes, you’ll want to know what you should do. The SAS Survival Handbook is one of the best survival books out there. It covers primitive camping, edible plants, encountering wild animals - even disaster situations like nuclear war. It’s packed full of good-to-know actionable information. And it’s a blast to read.

In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.

Apps begin to get more complex—and costly—once user authentication is involved. The main reasons for that are all the other expectations that come with user authentication. Typically, they include interacting with data (e.g., favoriting an article), syncing data across devices, push notifications, and perhaps collaborative features (e.g., inviting a family member).
I hope to build my own stand-alone dream shop sometime in 2015 – in the Texas Hill Country. I’ve not yet found the right lot, so much is yet unknown….but am thinking roughly 30′ x 40′ overall, with 10 or 12 foot ceiling. At one end, there will be a 10′ x 30′ space walled off into three spaces: a small finishing room, an office/design space, and a half bath.

They say nobody ever started a small business out of a love for numbers, but if you really want to stay the course, you’re going to want to fall in love fast. It’s only by keeping detailed accounts and tracking your business’ numbers over time, (net sales, cost of goods sold, and average transaction size) that you’ll start to gather the actionable insights you need to make intelligent business decisions.
×