Then there are material considerations, such as how to bring full-size sheets of plywood home to cut down to size (you don't). And safety and cleanup are two more concerns: Proper ventilation and dust collection, a cinch in a larger shop, can be quite a challenge (and a potential health hazard). Nevertheless, you can set up a great wood shop in a small space, and we'll show you what you need.
Overall I am very happy with the final results and I can’t wait to get back to making sawdust. The first project to be completed in the new shop is going to be a Queen Size Platform Bed for one of my favorite clients. I mentioned in a previous post that one of my goals this year was to get back into doing client work and this is me making good on that promise. I can’t wait to get started!
With such an unstable job market and it being harder to get employed, more people are moving into entrepreneurship and being self-employed than ever before. Woodworking is a fantastic business opportunity, but you might feel that you don’t have the space or money to set up your own workshop and sell your goods. If that sounds like you, then you should check out Ultimate Small Shop by Ralph Chapman.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
In my opinion, the best shop space is a flexible one. I know many folks expected that after setting up my shop so many times, I would be able to design the PERFECT shop space including a finishing room, a dust collection closet, and even some internal walls. But the truth is, the most important lesson I learned over the years was to expect change. My shop is not a static entity. It is more like a living breathing creature that adapts, evolves, grows, shrinks, and changes configuration. Committing to an internal spacial arrangement too early could yield disappointing results. This is why you won’t see me placing dust collection ductwork in the floor. I need to work in a space for at least a few months before I can be confident in my initial setup. Even then, I fully expect things to change at some point. If I made too many restrictive and/or permanent decisions ahead of time, these changes could be difficult or impossible to implement. So my best piece of advice is to forget about the concept of perfection. Instead, focus on flexibility. The ideal shop, in my mind, is little more than 4 walls, a roof, and a butt-load of outlets and lights. So here are some of my basic general goals for my new shop space.
Many retail fixture and display companies provide store planning and design services to their customers. Though typically not free, these in-house design services can be far less expensive than hiring an independent designer. Plus, they can help streamline the process of store layout and planning, along with the purchasing and installation of displays and fixtures.
Location, location, location is quoted so often for a reason. When starting a small business, the wrong choice could hurt your business before you’ve even had the chance to open the doors. Take the time to really understand your customers and do everything you can to gather real world insights that will help you determine the viability of your potential new space.
Power walls are your go-to spot for hot finds, new items, and seasonal features that attract instant attention and pull customers through the entry area and into your store. These areas are likely going to change frequently and you need to plan for it. Outfit these spaces with versatile displays that can be easily changed to showcase various product groupings.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
However, my guess is around $250,00 t0 $300,000. So as you say you will have a good mortgage to pay for. So excuse me for being nosy. I am retired and I have started setting up my shop in my two car garage. It is not insulated just bare walls and open ceiling. I am going to start doing some projects and will keep watching your shows. I was a Computer Engineer and although I liked my job i always had that desire to get back in wood working and now I am doing just that.
“Your sales floor is a living, breathing entity that needs to change—frequently—in order to flourish. It’s the retailer’s job to make that happen. If your store is filled with the latest and greatest products, but your sales are in a rut, it could be because your customers are bored. They come to your store not just to buy; they come for ideas and inspiration. And they come to be entertained—even when they don’t buy anything, that experience is what brings them back.”
Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.
There seems to be two things I like looking at and they are work benches & work shops. I too use my work shop for several other activities. I currently have a basement shop with a walk out entry, which is roughly 340 square feet and shaped like a flat s and has less than 8' ceiling height. In that shop I have an old Unisaw w/50"fence, 8" jointer, 15" planer, 10" sliding compound saw, 14" bandsaw and various & assorted power & hand tools. Also in the same space I have a small closet, dog grooming tub, & a space where a bathroom was roughed out. It is far from finished space and I have plans to put up a ship lapped paneled walls and fix up the closet for tool storage. I also plan on putting a cyclone in the bathroom space along with a tolet. I can work in the space as it is pretty well but the studded walls, insulation, & dust make the space somewhat uninviting.
Something I’d like to add to this comprehensive branding guide is that packaging can be a great branding tool, because it puts your business in front of new and repeat customer. This opens the door to lots of new sales. And friends, family and even strangers can be very influential! If your packaging is distinctive, people ask about it and you’re likely to get referrals if they love your product.
Just a quick note about light spectrum. I went with 6500k because that’s what I like to film in. The daylight spectrum makes it easier for me if I decide to open the blinds, letting in some natural light. For the average woodworking shop, I think 5000k is probably a good choice, although some folks really enjoy the crispness of a 6500k light. But you should test them out for yourself to see what you prefer.
When leasing a retail space, there is always risks involved. Your goal should be to minimize these as much as possible by considering every angle and asking the right questions. For example, does the landlord intend on erecting scaffolding on the building at any point during the lease? If so, can the rent be reduced to reflect this situation? You will also want to ask to have a clause included allowing you to sublet if necessary, which can be important if you ever find yourself struggling to make payments.
Amenities and Services – You’ll want to understand the full range of amenities offered by a commercial space. These amenities and services may include such things as communal rooms, free Wi-Fi, loading bays and docks, dining options, outdoor space, sewage and utilities, on-site security, and more. The zoning of your business will often dictate the type of amenities and services you require.
I totaly get not wanting to get into the cost part of the shop. We just went through a house renovation, and my stock answer to the ‘how much’ question is either ‘enough’, or ‘enough that was right for us’. There is a quality of life or utility aspect that every person needs to figure out for themselves. And, I would think not having to bounce around from garage to garage anymore has gotta be worth something!
Different approach in that they hung one end of the sleeping platform with hooks and U bolts. One of the best write ups with full details about rigging up an electrical system with second batteries and an isolator, as well as using power inverters. They were then able to incorporate cool things like a mini fridge, lights, and mini PC fans for air circulation.
Large or small, most retail stores use one of three basic types of retail store layouts. Which type you use depends on the kind of store you have and the products you sell. For example, grocery stores usually use grid layouts because they are predictable and efficient to navigate. Boutiques typically use more creative layouts that allow businesses to highlight different products.
Before starting your small business and opening its doors, it is important to take some time to define your end goal. While it almost goes without saying that this goal will be subject to change, it is only by recognizing and clearly articulating your long-term ambitions that you can provide yourself with a compass that will guide every business decision.
What about when you’re camping? Well, most campgrounds (including many free National Forest and BLM campgrounds) have some sort of bathroom situation. If there’s not an actual running water bathroom, you’ll typically find pit toilets (aka vault toilets), which are basically much nicer/cleaner permanent porta-potties. We also recommend picking up a good poop shovel for those times you’re camping in a wilderness area without bathrooms.
Concrete garage floors can work as a workshop surface, but over time they stain and you’ll end up tracking a lot of dust and dirt into your home. An epoxy floor finish is easier to clean and can also provide extra grip. For a softer surface that will help your joints when standing a long time, check out those restaurant grade rubber floor mats or some durable options that include garage floor tile.
The right first step online for most stores and restaurants is creating a Google Local Business Listing. Google accounts for 90% of all global organic search traffic and more and more of that traffic is coming from mobile devices. Chances are, your customers are using Google to find you, so you’ll want to make sure your hours, description, contact details, address, and images are all accurate.
Once you’ve considered your commercial property options and their associated leases, it’s time to choose one or more commercial spaces and negotiate the leases. When formally entering into a commercial lease negotiation process, you’ll want to start by requesting the terms in writing. This request can come from you or your broker and is supplied by the landlord’s broker.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off serious cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bottom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thickness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop without excessive grunting, so that made it very simple to install. The planer has a significant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.