By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!
We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Wide aisles also prevent the dreaded butt brush, a term coined by top retail consultant Paco Underhill. His studies show that both women and men avoid tight or crowded aisles where they might brush bottoms with other shoppers. Really, this is a thing! Learn more about Paco’s retail research and insights in his book, Why We Buy: The Science of Shopping.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
One example is testing your products and services for their desirability through ecommerce. It might turn out that your core product line will actually be much smaller than you originally envisioned. Equally, there are now a number of services (such as storefront.com) that will allow you to secure a pop-up lease in some incredible spaces, often for only days at a time. It might just turn out that your dream location isn’t as great as you originally thought.
By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!

Hey Marc. Just wanted to send a huge congrats your way for this milestone. It’s been pretty awesome to follow you on this journey since I discovered you on iTunes some 5 or 6 years ago. Mad props for what you’ve done to grow and enhance the online woodworking community as well as woodworking as a whole. I think with todays generation (as well as future generations) growing up behind a computer, the work that you and the rest of the podcasting world do will go a long way towards bringing new people into the craft. I hope that in the future you are able to start a series of videos showing how you introduce Mateao to the craft. Keep up the awesome work!
Garage spaces are usually not insulated, and garage doors on most homes have very poor insulation. That means it’ll inevitably be super hot and stuffy in the summer, and freezing cold in the winter. To be comfortable in your workshop you’ll need to take the extra step to insulate your garage and set up some space heaters, and some portable floor or window AC units. Having to wear a heavy coat while you work will impede your DIY efforts and nobody likes working in a sauna.
Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.
Once you know your top priorities, you can start thinking about the space each element can take up and where it should go. It is like putting the pieces of a puzzle together when you're working with a small space, so don't get frustrated if it doesn't work out right away. And know that you'll likely have to make some sacrifices. Play with a few options, and choose the one that works best for your situation.
At a time when you’re focused on getting in front of customers as quickly and as often as possible, it can be hard to think about official requirements like registering a business name or deciding on a legal structure. Still, now that you have decided to start a small business or buy an existing one, one of the first critical steps is determining the business entity that's right for you.
The on the go mode is ideal for when I’m just driving all day and need to pull over and get some rest, be it in a parking lot, a residential cul-de-suc, or wherever. I usually toss a couple of items in the cab of my truck and crawl into the “coffin” sleeping arrangement for a quick night’s rest, but I can also crawl in without placing anything in the cab.
Having a plan of action is key to learning how to start and run a successful small business. Whether you are looking for funding from a bank or angel investor, or are lucky enough to completely fund your venture on your own, an articulate and well-thought-out business plan will help you define what your business stands for and what it intends to become over time. As the age-old saying goes: “A goal without a plan is just a wish.” Don’t put your business idea in the hands of fate. Plan thoroughly, give yourself some benchmarks for success and be prepared to innovate as you go.
We do not recommend using Reflectix to insulate your walls or ceiling. Without an air gap, the R-value of Reflectix is about R-1. Even if you have the recommended ¾” air gap next to the Reflectix, the R-value per inch is less than R-3. There are much more efficient and cost-effective insulation materials out there for these purposes - you’ll be better off filling the space with rigid foam board.

Composting Toilet: Nature’s Head Dry Composting Toilet. Much more expensive but also more pleasant and environmentally-friendly. Just drop your load and add some peat moss/sawdust, and your toilet will naturally break down your poop into compost. If the Nature’s Head toilet is out of your price range, you can also try making your own composting toilet.

You may want a garage door if you will need to access your shop with large workpieces or tools, or if you or future owners will ever want to use the space to park a vehicle. Garage doors are notoriously drafty, however, so if you think you can live without one you will probably be warmer. Instead, you could opt for out-swinging double doors. In a small shop you can, at a pinch, rip longer lengths of lumber by feeding the material out of either a strategically placed door or window.

Ideally, the stands should lift the speakers to roughly ear level of a sitting person. This is important because it aligns the ​subwoofers and tweeters relative to the ear and achieves the best balance of sound. The high frequencies are often missed when speakers are placed too high or too low. Speakers placed on a shelf or table often cause the surface to vibrate, thus distorting bass. These speaker stands isolate the speaker's vibrations from the floor, allowing you to hear the bass from the speaker and not the vibrations from a shelf, table or floor. Speakers come in various sizes and shapes, so the height of your speaker stands is dependent on your unique speakers. For this project, we give you the dimensions suited for the speakers shown in the photo, but you can alter the design to fit your individual needs.

However, while this product might draw the customer through the door, it will not, on its own, make your business a success. A strong small business has to be resilient to the challenges the world can throw at it, whether that means an economic recession, sudden fluctuations in commodity prices, or problematic suppliers. And a big part of resilience comes in the form of diversification.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Well, I thought about that I don’t want all that dust to kind of infiltrate everything else in the building. So actually instead of putting in some kind of dust collection system, I thought that I would probably just put a nice shop vac here. And then I have room that I can bring some hose back behind this column and then you know if you’re sitting here working on something we can have adapters that go right into a miter saw or right into a sander or have a little outlet more or less to lay up on the counter that would collect all of the dust. And the same thing could happen on any of the work we do out here.

A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks! 

Setting up and running a small business is awesome, especially if it’s your first business. Is it tough at times? Yes. But if you don’t build your dreams, who will? In 2010, according to the U.S. Census Bureau, there were 27.9 million small businesses nationwide. This number has trended upwards over the last decade, accounting for 64% of net new jobs created between 1993 and 2011. In a world that appears to be dominated by today’s retail giants, it’s easy to overlook the huge impact that starting a small businesses can have on our U.S. economy. However, these numbers illustrate something that we strongly believe at ShopKeep – that the brave folks who open new businesses are the backbone of the nation’s economy and the lifeblood of our local communities.
Once you’ve got that, you’ll want to familiarize yourself with your tax obligations as a employer, including providing required employee benefits such as social security and workers’ compensation. As an employer you are also responsible for withholding federal and state taxes from your employees’ paychecks. What’s more, you are obliged to ensure all withheld tax is forwarded to the government within a defined time frame (usually a matter of days after the paycheck was issued). Failure to do so can result in a fine.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
The dream of a dedicated home shop is a common one among woodworkers. Whether you currently borrow shop space, work in your driveway or side yard, or compete for a corner of your basement with Christmas decorations or your fur­nace, you may be ready to build your own space that will allow you the free­dom of more room and time, and will also keep dust, fumes, and noise under control. Every design/build situation will be unique but there are a series of consid­erations that you will face in the design and construction phases of your project. Let’s walk through the process and dis­cuss the questions that you will need to ask yourself and others as you approach this project.

You know I can remember my very first workshop, and the very first power tool I ever bought when I was nine years old. Well, I have still have it, doesn’t work anymore but it lasted for 20 years, and I bought it from a mail order catalog for $11.41. I’ve held onto it all these years, because I knew I would find some special place sooner or later that it needs to rest. Well here’s a nice spot right here, I think that’s where it’ll end up.


Hey Anthony, I guess the big question is what part of the country you’ll be sleeping in and what sort of weather you can expect… I would imagine when conditions are fine that a warm sleeping bag would be more than enough (I used to do that before I had a canopy). You’ll just have to worry about rain (snow?) and other inclement weather, but otherwise I don’t know why not. A cheap bivy sack from an army surplus store might be a good addition as well.
Well, my workshop is finally complete and I’m ready to take on just about project that comes down the line. And I’m pretty well set up here. I’ve got a great workbench, plenty of table space over here that easily rolls around the shop if I need it, lot of storage space down here, I can tuck these tools away or bring out any new ones that I need. And as you can see I’ve got plenty of supplies to tackle just about any project.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
There is a profound difference between a good idea and a thriving business, but as the saying goes: “A journey of a thousand miles begins with a single step.” At a certain point, turning your dreams into reality is as basic as putting a plan in place and, step by step, making it happen. The good news is that there has never been a better time for starting and learning how to run a small business.

For those of us building apps, there's an increasingly larger burden on us to meet the expectations of our users. We've outlined the considerations of what makes a great app in the past, which are more relevant than ever. Users simply don't have the patience for apps that are overly complex, slow, or buggy. The best apps are personalized, highly contextualized, and touch human emotion. Meeting those user expectations is significantly challenging.


This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
They say nobody ever started a small business out of a love for numbers, but if you really want to stay the course, you’re going to want to fall in love fast. It’s only by keeping detailed accounts and tracking your business’ numbers over time, (net sales, cost of goods sold, and average transaction size) that you’ll start to gather the actionable insights you need to make intelligent business decisions.
×