The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.

It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.


Really enjoyed watching the video of the shop build. You will be turning out great pieces in no time. At the end of the video it looks like you have your dust collection system up and running. Where did you purchase the duct work? I thought I remember you talking about this in the old shop. Did you use regular HVAC 4″ round duct or a heavier piece. Thanks for the insight and good woodworking.
I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
With the third category, franchise businesses , the risk of getting started is potentially the lowest of all when it comes to starting a small business, as you are often buying into a clearly established business model. You will also often benefit from the initial support of the franchisor, including advice around site selection, training and orientation, employee hiring, and product mix coordination. This support and assurance, however, comes at a premium. On top of the normal startup costs (space, equipment, etc...), you’ll have to pay a franchise fee to the owner, which is often tens of thousands of dollars, as well as a percentage of your revenues on an ongoing basis.
Thanks for leaving a comment, Rob! I didn’t find that it limited where I felt comfortable camping, but I always tried to be discreet… Waiting until few if any people were around before I hopped in and usually peeking through the windows so I’m not hopping out right next to someone loading their groceries or whatever. I slept in all sorts of random places in that time on the road, more often than not it was in permissible camping areas, but there were other times it was more frowned upon–from grocery store parking lots, to auto repair places, etc. Certainly is more likely to guess that someone is camping in it, but I only got hassled once (by a rent a cop telling me to move on).
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.

Tired of the rat race, I opted for early retirement. Looking for something to do with all my free time, Ultimate Small Shop Ebook Free I started crafting and am now making a nice supplemental income from it. As a crafter and a businesswoman, I feel I have some valuable insights into the craft business that I can share with you. At some point in your progression from crafting for fun to crafting for fun and profit, you go from handcrafting individual items for yourself and friends to filling quantity orders for a broader marketplace. That’s the time to take a very business-like approach to your craft business. This needn’t be daunting. You don’t need an MBA or management experience – just a bit of common sense. If you’re going to do this for profit, you need to understand Simple, right? But very few people get it. Look at the high failure rate for new businesses. It takes an effort to be successful, but the task is hardly impossible. Traditional craft retailing methods are what most crafters use to get started. They’re the easiest way, especially if you don’t know if anyone will buy what you make. I believe that there is a market for any well-made craft, whether decorative or useful. The problem facing many crafters is how exactly to go about selling them, or more accurately, finding paying customers. The fact is that there is an awful lot of competition out there. My own business got jump-started by my “circle of friends”. Ultimate Small Shop Free My friends noticed and liked my calling cards and began to ask me to design and make cards for them. Starting with just Broderbund’s Create-a-Card program, I was soon earning a nice supplemental income in just a few hours a week. It probably helped that I was retired and live in an area dominated by retirees. But I think that everyone has a “circle of friends” either socially or at work. Of course, you don’t want to impose on their friendship by making a hard sell, but rather use or display your crafts in front of your friends to see if they draw any interest. If they do and if they’re priced right, you’re on your way to craft retailing for profit. If your “circle of friends” market starts extending to friends of friends, you’re probably ready to tap the general marketplace of craft retailing. Most crafters are aware of the periodic craft shows put on by local groups or even by the local Parks Departments. These usually cost little or nothing to join and should give you a fair idea of whether there is any broader interest in your craft. What better way to jump into craft retailing? There are also organized craft shows that tour the country, Ultimate Small Shop Legit most of which charge an entrance fee for participants.
When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers. 

Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts.  

Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Marc, I enjoyed the video. Thank you for sharing your dream shop with us. I would be interested in seeing a demo video on your Clear Vue cyclone dust collection system. Which one did you obtain & what type of duct work did you use (seamless?) Do you plan on enclosing the unit in a closet to reduce noise and keep dust confined? Do you have to purchase special expensive plastic dust bags for the drum? Is it hard to pull the bag out of the drum for trash collection? If you could address these questions in a demo video I would appreciate it. Oh, perhaps you already have one …. I will check out your video archives. Thanks again and keep up the great work!

For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.


Hello! My name is Donna Jean. I love to read books and my job is to write a daily review of all the novelties in the world of eBooks. I allow only the best of them to be published on my website. I really hope to make our world more bright, beautiful and kind. You can participate by downloading any book from my site, and you will receive health, luck, kindness, and love, which will support you during all your life. Wishing your dreams begin to come true, and every tomorrow be happy for you. Thank you! ❤❤❤ 

Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
Well I think I’ll have plenty of light once we get all of 24 bulbs in place. I’m really glad I saved those old fixtures. Hey another thing we’re reusing, and I’m really glad I saved, is these old cabinets that we took out of a kitchen renovation a couple of years ago. This will be perfect to serve as our base cabinets so that we can build our sturdy countertop on this side of the shop.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.

Most of today’s POS systems have integrated inventory management software that allows you to put hours back in your week, whatever the volume of your stock. A quality point of sale system will allow you to manage pricing changes, track product availability, cross-check inventory, and automate reorders with ease. All of which are crucial in helping you develop a deeper understanding of your business, enabling smoother day-to-day operations and smart purchasing decisions.


“Walk past your Decompression Zone and look to your right. The first wall you see is called a Power Wall, and it’s another key merchandising area. And because it’s one of the first things shoppers see after looking or turning right, it’s a perception builder. Use your Power Wall(s) to display important departments as well as new and seasonal items to create vignettes, tell product stories, and to feature high-demand and high-profit items. (Note: Your store has more than one Power Wall. Stand in various places throughout your store and look around—the walls that stand out are your Power Walls.)”
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Do you have a business license? Do you have a permit to open a food service establishment issued by the local health department? Are you applying for a permit to modify the building you wish to occupy? Do you have a health permit from the county health department? Do you have a signage permit? How about an alarm permit from your city or county fire or police departments? These are just a few of the questions you need to ask yourself.
Since there’s less wiring involved, installing LED strip lights is much simpler than puck lights. You also won’t need to cut any holes because strip lighting should come with its own adhesive. We’ve seen most vanlifers stick strip lighting down the side edges of their ceilings. However, it’s not as easy to create separate lighting zones as it is with puck lights.
The dream of a dedicated home shop is a common one among woodworkers. Whether you currently borrow shop space, work in your driveway or side yard, or compete for a corner of your basement with Christmas decorations or your fur­nace, you may be ready to build your own space that will allow you the free­dom of more room and time, and will also keep dust, fumes, and noise under control. Every design/build situation will be unique but there are a series of consid­erations that you will face in the design and construction phases of your project. Let’s walk through the process and dis­cuss the questions that you will need to ask yourself and others as you approach this project.
Solar Shower. For easy, inexpensive showering in wilderness locations, nothing beats a good solar shower. This is basically a bag of water that you leave out in the sun until it heats up, then hang it from a high place and shower using the attached nozzle. 5-gallon solar showers should get you about 5 minutes of good water flow. There are also pricier but more convenient pump-operated solar showers that you can buy.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.
I hope to build my own stand-alone dream shop sometime in 2015 – in the Texas Hill Country. I’ve not yet found the right lot, so much is yet unknown….but am thinking roughly 30′ x 40′ overall, with 10 or 12 foot ceiling. At one end, there will be a 10′ x 30′ space walled off into three spaces: a small finishing room, an office/design space, and a half bath.
Check your local papers, especially the free shoppers, for information about upcoming shows Another venue for craft retailing is at the local flea markets that spring up in every community just about every weekend. Again the entrance cost is usually minimal. Ultimate Small Shop Result The only other thing you need is a little marketing savvy. With little cost and some effort, you will be well on your way to knowing whether there is a market for your craft. Once you know that, you can move on and think about other ways of selling, such as in galleries, on consignment, on eBay or from your own website. Once you spend your precious time and energy creating a scrapbook, make sure it lasts! There are a few simple things you can easily do to ensure that your scrapbooks look just as good as the day you finished them, for years to come. The first thing to avoid is paper that is not lignin-free. You’ve probably heard that before, and it is true, but what is lignin anyways? Lignin is a stiff component of a plant that quite literally holds it together. Although lignin is necessary for plants and trees, you want nothing to do with it! After a while, lignin will cause photos, fabrics and other paper that touch it to turn brown. Yes, the lignin-free paper does cost more, but it is a vital part of preserving your cherished scrapbooks. If the paper is not lignin-free, it will eventually discolor your photos and other materials touching it. So when buying paper for your scrapbooking projects, be sure to look for packages that say “lignin-free,” because if it doesn’t say it, then it most likely isn’t.The fabric is a big concern for preserving your scrapbooks, but unfortunately, it is often overlooked. Many people assume that all fabrics are acid-free, but they aren’t. Silk actually goes through an acid bath during the manufacturing process, as well as many tie-dyed fabrics. This isn’t to discourage you from using it, not all. Just try to make sure that no photos directly touch fabric, and if you need them to overlap, make sure there is a layer of paper between the two. Another consideration when using fabrics is if the color will bleed off onto your page and other things touching it. To test for this, cut a square inch off and soak it in a glass of water overnight. If there is no color bleeding from it the next day, then there isn’t any risk to your scrapbook. But if you do see color in the water, or collecting at the bottom of the glass then don’t use that fabric in your scrapbook at all. When using glitter, be sure there is a top layer of spray adhesive to lock them down, or better yet use special glitter glue where the glitter is mixed right in. If this is not done right the glitter will slowly fall off, and loose glitter means scratched photos. After you have planned the layout for your photos, be sure that you are using the right kind of mounting tape for them! Regular mounting tape is fine for buttons and bottle caps, but when it comes to mounting photos you need to use special photo mounting tape which is completely acid-free. Ultimate Small Shop Member If you don’t, your photos will slowly discolor. The tape should say “acid-free” right on the packaging.
Solar Shower. For easy, inexpensive showering in wilderness locations, nothing beats a good solar shower. This is basically a bag of water that you leave out in the sun until it heats up, then hang it from a high place and shower using the attached nozzle. 5-gallon solar showers should get you about 5 minutes of good water flow. There are also pricier but more convenient pump-operated solar showers that you can buy.
Like most things in life, we believe that entrepreneurship can be learned, you just have to be willing to put one foot in front of the other. Aftering reading How to Start a Small Business 101, you’ll be equipped with the essential tools and resources you need to succeed at planning, raising capital, and executing crucial day-to-day business operations.

There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior fin­ishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electri­cal and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.


Once you have your space secured, hang some pictures in the windows that illustrate what’s to come. It’s also a good idea to provide leaflets that people can take away with them and hang a clipboard and pen on the front door where people can sign up to hear more about your business. This list is pure gold! So once you have it, why not stage a launch party and invite the local community (and local journalists). The first step for any business is always getting people to try out your products!
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
Hey Kasey, I don’t do anything for insulation, I treat truck camping just as I would cold weather tent camping. Just bring a good sleeping bag and learn how to manage in the cold. Usually the side wall of the truck is not at a perfect 90 degree angle, so you will need to check out the angle and compensate. You can hold up a small piece of 2×4 at the back to judge the angle and make a few test cuts to ensure it sits “flat” aka level.
There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior fin­ishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electri­cal and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.
Once you know your top priorities, you can start thinking about the space each element can take up and where it should go. It is like putting the pieces of a puzzle together when you're working with a small space, so don't get frustrated if it doesn't work out right away. And know that you'll likely have to make some sacrifices. Play with a few options, and choose the one that works best for your situation.
In a small store, these are usually one and the same. In stores where customers don’t shop with baskets, Lesley recommends having a checkout counter large enough to hold products as customers continue shopping. Remember, empty hands pick up more products, and that leads to more sales. Also, make sure checkout counters are large enough to handle the checkout process efficiently and allow space for customers to set down a handbag.
Secondly, your size allows you to laser-focus your attention on the right audience. Walmart wants to sell everything to everyone. So maybe instead, you just focus on selling colorful earmuffs to children in the Mission District in San Francisco. This kind of clarity allows you to compete for search rankings on Google, key positions on Yelp and other business recommendation engines, and for space on social media.
The idea behind this segment is to find products that solve common problems we face as homeowners. And the cool thing for me is that I get to learn a lot about the professional side of home improvement. Well, I’m looking for do it yourself items. For example, do you know why carpenters pencils are shaped differently than ordinary round pencils? So they won’t roll off of an inclined surface like a roof. And the larger size allows you to draw fat lines as well as fine ones while you’re marking lumber.

If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.
If you want to hit the road as soon as possible, then a Class B/C RV camper is a great option to consider. These vehicles are typically move-in ready, and barring any mechanical issues shouldn’t need much customizing before hitting the road. Class B campers (aka “campervans”) are built inside a van body, while Class C campers have a custom body built on a van cab/chassis.
The right first step online for most stores and restaurants is creating a Google Local Business Listing. Google accounts for 90% of all global organic search traffic and more and more of that traffic is coming from mobile devices. Chances are, your customers are using Google to find you, so you’ll want to make sure your hours, description, contact details, address, and images are all accurate.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.
Ralph has three decades of professional experience in using workshops and setting them up, and it certainly shows in his Ultimate Small Shop guide. You’ll find all the important information you need to put together your own workshop, including how to save money when putting one together; all the tools and equipment necessary to run a workshop; tips for choosing the best equipment; factors that should be considered when buying things for the workshop; and so much more. If you’ve considered setting up a workshop but feel you don’t have the time, space, or money – then you need to check out Ultimate Small Shop – How to Set Up a Complete Small Workshop on a Budget.

Well I’ve been kind of fighting that, because I wanted to keep it open to where you could have the flexibility of moving things in and out. It probably makes sense. Actually have another old set of cabinets I thought about putting here, maybe put some really good casters on it to where you could keep it here. I’m also, wanted to be able to store like drum sander, other things that can go under it and then you can take those out and put them on this.
One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks!

This OXO palm brush really helps us conserve water while washing our dishes. We fill the reservoir with water and a few drops of Campsuds, and we only squeeze out what we need - so it takes care of both the initial rinse and getting our dishes soapy with minimal water usage. It’s also very compact, and the comfortable shape makes it easy to scrub dishes.
Chances are if you’re starting a new small business, you’re not afraid of a little risk. However, it’s also highly likely that you have invested a large amount of money in this new endeavor. It is only prudent to take sensible steps to minimize the impact of unexpected events, like the untimely death of a business partner, a lawsuit from a customer or employee, or a freak accident of nature.
×