If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based busi­nesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of run­ning into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibili­ties that your property will allow.
While not as large as I would have liked (is a wood shop ever big enough?), it is about twice the size of my previous shop. It measures about 12 by 25. Fortunately I had managed to find quite a bit of shelving before the move, so I was able to install shelving along two walls. And the work benches were made from wood salvaged from packing crates from Europe and left over yellow pine car siding and flooring from remodeling the old house.
It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
Many DIY campervans have kitchen units that are directly behind the cab, sealing it off from the rest of the van. These layouts offer increased privacy and stealthiness, especially if you completely wall off the cab, and open up some space in the back of the van. This layout can be paired with a lengthwise bed, fixed bed, or convertible dinette bed. You can also place your propane and water connections right by the door, making refill easier.
There’s a reason why some of the biggest players online have names that are essentially gobbledegook: Zappos, Skype, Zynga. While there’s certainly some psychological naming principles that often come into play, at the most basic level, it’s simply easier to find this space online and then strive to own the brand name in the minds of consumers. How important this will be to your small business will depend on a number of variables, including your intended size, location, and your desire to exploit ecommerce as well as a local brick-and-mortar business.

If you’re moving into a space that requires renovations in order to fit your business needs, you’ll also want the landlord to take on responsibility for that work. We’re not talking aesthetics here, we mean necessary renovations such as improved data connectivity. If you have to do the work yourself, it’s advisable to ask the landlord for a rent-free or reduced-rent period. You should also make sure that any additional alterations you have in mind are acceptable and would not be in breach of the lease. Last but not least, always make sure the do’s and don’t of what can and cannot be done is put in writing, it will save you a lot of headaches later.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.

Conversion vans have some pretty sweet built-in amenities, including high-tops for extra headroom. Many have comfy captain chairs, leather seats, mood lighting, TV/VCR, and a rear bench seat that folds down into a bed. If you’re not picky about your living situation, this could be all you need to get started. And if you gut it and customize it yourself, the high top offers tons of great storage options that other vans just don’t have.
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
On-demand apps incorporate many of the elements seen in apps with logins and social features. Like ecommerce apps, they also include a transactional component, because users need to purchase goods and services. Unlike social and ecommerce apps, however, on-demand apps essentially require two completely unique user experiences. For example, an Uber driver needs advanced mapping and routing functionality while a rider doesn't. Similarly, the driver doesn't need to do a payment while a rider does.
We exhausted our entire life savings on this project and entered into a lot of debt at the same time. And now it’s the ongoing maintenance, repairs, insurance, and upkeep on this rig that make it almost impossible for us to keep it on the road. This is where I’m hoping to get that “let’s sponsor you to travel across America and meet the fans” call from Hasbro or Paramount one day soon.
When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
×