4. Avoid a cluttered look. Owen managed to add more merchandise but avoid a cluttered look by using neutral colors, such as ivory and gray for furniture and larger items. She then accented the space with smaller brightly colored items like vases and pillows. She also makes sure not to crowd her merchandise too closely together. "We try to make it look elegant and give it some space," she says.

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Will this make me money? If it will not, cross it out. If you want to keep it on, please rephrase your goal so the outcome can be money driven. For example: Grow Instagram following (bad) vs. use Instagram to drive traffic and sales to website (winner!). This way, you can break that goal down into tasks ( ill show you that in an another step) and those tasks will lead to you actually making money with that goal instead of with just a larger Instagram following.
Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.
Marc, I enjoyed the video. Thank you for sharing your dream shop with us. I would be interested in seeing a demo video on your Clear Vue cyclone dust collection system. Which one did you obtain & what type of duct work did you use (seamless?) Do you plan on enclosing the unit in a closet to reduce noise and keep dust confined? Do you have to purchase special expensive plastic dust bags for the drum? Is it hard to pull the bag out of the drum for trash collection? If you could address these questions in a demo video I would appreciate it. Oh, perhaps you already have one …. I will check out your video archives. Thanks again and keep up the great work!

Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.


“Beware suppliers bearing gifts. That ‘free’ refrigerator from the drinks supplier is never really free. You can quickly find yourself tied into sub-optimal deals because of a reliance on this hardware. If you have access to the capital, do yourself a favor: Buy your own fridge and negotiate from a position of strength.” — ShopKeep Founder and Experienced Small Business Owner
If you want to operate your business under anything other than your own personal name, you’ll need to register your chosen ‘fictitious’ name with the appropriate county or state authority, otherwise known as registering your “Doing Business As” (DBA) name. The correct filing authority varies state-to-state. The Small Business Administration (SBA) provides a helpful tool to help you find the relevant authority for your state.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
Well I was just thinking about all of the supplies I’ll be able to keep in this large shelf unit we just installed in our workshop. Hey, that’s we’re doing this week is creating a very practical realistic workshop where we’ll be doing a lot of projects for the TV show, but it’s also going to be used by my construction company so it really has to be set up properly.
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.

I have been working on building out the space, starting with a new welding table and small material/saw rack. I was able to dedicate a 20' x 28' area to fabrication. I need to figure out some things like angle grinder storage, fume exhaust hood and cold saw set up, but I will get there. Power is one nice thing with a 400A 208VAC 3ph supply panel. Also got the compressor in a sound dampened closet with cooling so the noise level is down significantly. Oh ya, dedicated 15 ton AC for the shop has been nice.
We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
The first step in choosing a business location has little to do with site evaluation. It’s about understanding who your customers are. What kind of people are they? When and where do they work? How do they spend their free time and extra capital? Get to know your potential customers and you’ll have a far better chance of finding both a site and a property that they’ll want to frequent. Once you know who they are, you need to ask yourself if there are enough members of this target demographic near your intended storefront location. If so, what time of day they are most likely to be near your storefront? And, will it be quick and convenient for them to stop in?
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
Simply get a one-inch drywall screw and drive it into the hole right beside the hook. You want to use a one inch screw because you don’t want to hit the wall behind it and you just drive the screw in until the head of it is tight against the hook, it’ll just act as a shim, and you’ll see once I get this all the way in, it lock the hook in place, and now when you take the tool on and off it won’t come off. The hook won’t pop out.

One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks!
Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
As a retailer, it's possible to use furniture, displays, racks, and other tools to create a clear path for your customers through your store. This will vary greatly depending on the size and your general store layout. However, you know that most North American customers will naturally turn right — so, your next job is to make sure that as they do, they also continue walking throughout your store to gain the maximum exposure to your products. This not only increases the chances of them making a purchase, but a well-thought-out path can be a great way to strategically control the ebb and flow of foot traffic in your store. 
Ryan, I have the same (almost) 90’s Toyota Pickup and love it! this is so helpful, and I will definitely be using this method. my main concern is that 1/2′ plywood sagging. do you notice it sags quite a bit or does it mostly hold up? my thought was to build the vertical bins a little wider, so that the plywood bed platform wouldn’t be under so much stress. the second issue im running into is wrapping my head around trying to organize and compartmentalize things appropriately. what do you typically put where so it is easy to reach and use?

Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Do you have 3 goals left? Great! That's the perfect number. Do you have more? That's okay as well. If you have more time to work on your business, then you may be able to accomplish more then 3. But it also depends on the type of goal you are trying to accomplish. I just recommend not trying to over achieve in fear of not accomplishing everything you set out to do. 
Apps in this scenario would be able to fully function without any sort of network connection. Historically, examples of standalone apps might be your settings app or the camera app that comes with your device. Even today though, those apps usually have some interaction with the network. For example, you can share a photo from your camera via messaging.

WOW that is a nice size shop! I am looking forward to more videos on the shop projects! We have been shopping for a house for over a year & have finally found one but it has nothing for me to use as my woodshop! I currently have a basement shop that’s 24×40 & it’s really huge for me I couldn’t imagine any bigger. Anyway I will be looking at building a new woodshop for myself (yes I am a female woodworker) & you have given me lots of great ideas so far. I am an Artist & wood is my preference, everything I make is quite small (no furniture or anything that big) but I have lots of specialty tools for what I do as well! Thank you for sharing your ideas & all that you do. Keep up the great work!
Our practical workshop is coming along nicely. We’ve created a big open space and added plenty of electrical power and lots of light. We’ve also added some great storage capacity using recycled kitchen cabinets and some old shelves. Now, with our tool compartment and work surfaces in place we’re getting very, very close, but I wanted to get a little input on the final details from some other folks who spent a lot of time making sawdust, so I asked my co-host Allen Lyle and our website editor Ben Erickson to look around and give us some of their ideas.
In the case of this guide we’re going to use an area that’s a little larger and show you the tools you’ll need to set up a small workshop in just a 10×8′ shed. The list of tools is generally considered enough to cover the most common tasks. Everyone will have their own opinion on this and naturally it depends on the work you’re carrying out. But the tools on the list should be enough to strike a productive balance between having enough to get the job done and not being caught short so you’re having to borrow a friend’s. Invariably people grow their collection of tools as the jobs dictate. You don’t necessarily have to buy everything at once, just build up your list as you need to.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.

At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 

When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Stop schlepping extensions cords across your garage floor. Make sure your workshop has enough power outlets to charge your tool batteries as well as power your corded shop tools. Your drill press or band saw shouldn’t compete for outlets with a charging drill battery, and you shouldn’t risk tripping over a cable that’s laid across your garage floor.
Trying to compete on price is rarely an effective long-term strategy, so it’s important to consider how you will differentiate your offering. Will this be with amazing customer service? Or maybe with superior product quality? Regardless of what you choose, how will you allocate your budget to make it possible? How will you market your small business? How will you get customers through the door?
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percent­age of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both dif­fer depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
With such an unstable job market and it being harder to get employed, more people are moving into entrepreneurship and being self-employed than ever before. Woodworking is a fantastic business opportunity, but you might feel that you don’t have the space or money to set up your own workshop and sell your goods. If that sounds like you, then you should check out Ultimate Small Shop by Ralph Chapman.
Nice video Marc. I did enjoy seeing the details of the construction process. Since becoming a homeowner and a woodworker (something that happened literally at the same time) I have become fascinated with anything having to do with the process of building and finishing and all the details in between. I thought of an off the wall question while watching this video and that is do you write yourself any kind of script for any of your monologues and/or narrating or do you just have a general idea of what you want to say and wing it?
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.
×