Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email firstname.lastname@example.org and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
You can see in this step how I notched each rafter to fit more securely to the walls. I also used a metal hurricane strap to secure each rafter to the wall. Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution. The walls are a simple board and batten system. The 1x3 trim covers the joints of the 4x8 OSB. They make much more high quality sheets goods to use as siding. However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet. I sealed the OSB and painted it with exterior paint. If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed. It has held up very well over the past couple years and I see no need to spend more money on it now.
With the third category, franchise businesses , the risk of getting started is potentially the lowest of all when it comes to starting a small business, as you are often buying into a clearly established business model. You will also often benefit from the initial support of the franchisor, including advice around site selection, training and orientation, employee hiring, and product mix coordination. This support and assurance, however, comes at a premium. On top of the normal startup costs (space, equipment, etc...), you’ll have to pay a franchise fee to the owner, which is often tens of thousands of dollars, as well as a percentage of your revenues on an ongoing basis.
“Every time I’m choosing a new a location, I head down there with a big flask of coffee and a clicker to count all the people that walk past. Then I walk to the nearest public transportation at rush hour and look at how people are heading home. I turned down one location because while it was right next to the subway, I noticed all the commuters were coming out of the other subway entrance. It turns out all the residences in that area were on the other side of the street.” —ShopKeep Founder and Experienced Small Business Owner
Finally, think about the overall color and feel of your workshop. A fresh coat of bright white paint will help your lighting go farther, but you might also consider adding a splash of color for fun. An accent wall or an epoxy floor coating are good ways to upgrade your workshop from drab to fab without adding fussy decorations that will get in the way of business.
Remember that you must allow three feet of pathway space between all display units to meet Americans with Disabilities Act (ADA) requirements. But customer comfort is more than a requirement. Studies have proven, time and time again, that customers do not like to be jostled when shopping. Allow generous pathways between fixtures. Experts recommend three feet, six inches, so customers can move freely, examine products, and carry items to your registers. This will keep customers happily browsing in your store and you in good standing with the ADA.
The good news is this: You are not a statistic. Think about this — if it was reported that small business owners over the age of 50 were more likely to succeed, would you wait until you were 50 to start a small business? Not likely. You would start when you felt ready. And that’s the point — only YOU can know when it’s time to take the plunge. Likewise, only you can make the intelligent decisions that ultimately mean the difference between success and failure when it comes to launching your business.
Wide aisles also prevent the dreaded butt brush, a term coined by top retail consultant Paco Underhill. His studies show that both women and men avoid tight or crowded aisles where they might brush bottoms with other shoppers. Really, this is a thing! Learn more about Paco’s retail research and insights in his book, Why We Buy: The Science of Shopping.
The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a concrete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.
Whether you end up looking at self-checkout counters, fancy lighting systems, special refrigerated cases, or any of a countless number of options, never forget that these are only tools to help accomplish your main goal. Your store needs to create an environment where customers want to be, where they feel comfortable and appreciated, and where that experience will prompt them to purchase (and hopefully encourage their friends to do the same). Equipment and technology decisions should always be made with your customers in mind.
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.