First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.
However, since you may not have "aisles" per say in your store, it's still important to think about grouping products in a way that makes sense from a shopper's perspective. Also, remember to keep "higher-demand" products displayed at eye-level while placing lower-grossing products at the bottom or above eye level. Lastly, It's recommended that you change up these speed bumps weekly or regularly enough to create a continued sense of novelty for repeat visitors. 
People tend to buy cargo vans for work and hold on to them for years, so many vans on the market can be pretty beat up. Although you can find inexpensive cargo vans in good condition, it can be tough to find anything with lower mileage - so be prepared for all that comes with owning a higher mileage vehicle. Cargo vans also don’t offer much headroom. There’s no way even shorter people will be able to stand in one, and the lack of headroom also cuts down on storage space.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
A grid floor plan, also called a straight layout, is a very efficient use of both floor and wall space. With fixtures and displays running parallel to walls, a grid floor plan maximizes every inch of available floor space, including the corners. Grid layouts are easy for customers to navigate and for store owners to categorize. Plus, they offer plenty of end cap and feature wall exposure for promotional items and seasonal products.
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
Will this make me money? If it will not, cross it out. If you want to keep it on, please rephrase your goal so the outcome can be money driven. For example: Grow Instagram following (bad) vs. use Instagram to drive traffic and sales to website (winner!). This way, you can break that goal down into tasks ( ill show you that in an another step) and those tasks will lead to you actually making money with that goal instead of with just a larger Instagram following.
Sounds fun right? Well the truth is — yes! It’s more than fun, it’s liberating. Sure, there is some risk involved (and a bit of a learning curve). But for those who do it right, who take advantage of the technology available, who build the right support network around them, who get funding from the right sources, and who choose the right people to work with, working for yourself is the new job security.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.

We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.


Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
×