The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.
First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.

However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
In my opinion, the best shop space is a flexible one. I know many folks expected that after setting up my shop so many times, I would be able to design the PERFECT shop space including a finishing room, a dust collection closet, and even some internal walls. But the truth is, the most important lesson I learned over the years was to expect change. My shop is not a static entity. It is more like a living breathing creature that adapts, evolves, grows, shrinks, and changes configuration. Committing to an internal spacial arrangement too early could yield disappointing results. This is why you won’t see me placing dust collection ductwork in the floor. I need to work in a space for at least a few months before I can be confident in my initial setup. Even then, I fully expect things to change at some point. If I made too many restrictive and/or permanent decisions ahead of time, these changes could be difficult or impossible to implement. So my best piece of advice is to forget about the concept of perfection. Instead, focus on flexibility. The ideal shop, in my mind, is little more than 4 walls, a roof, and a butt-load of outlets and lights. So here are some of my basic general goals for my new shop space.
At a certain point, you may decide that it is time to move on from your business. Whether you’re winding down a business that just didn’t work out, retiring (and maybe opening that beach bar in Belize), or cashing in on the effort you’ve put into creating a lucrative enterprise, you will hopefully have established your end goal well in advance so that the time to strategically exit will be clear.
Thanks! Yep, the canopy clamps and the grooves in the bed liner are the only things holding the side shelves and sleeping platform in place. You just pop off the clamps with a ratchet and the whole things lifts out / slides out easily. That’s what I did to treat the wood after construction, takes maybe 15 minutes to pop out. Very modular. It’s been in there for more than two years now, same wood, and everything is still looking good and working fine. I like it!
Hospitality expert, Chip Conley founded and grew the Joie De Vivre hotels from a single San Francisco location to become California’s largest boutique hotel management company. How? He understood the value of a unique vision when it’s consistently applied. He created each hotel to reflect the spirit of a niche-oriented magazine that he felt represented his target market. Examples include the Phoenix (Rolling Stone), the Rex (The New Yorker), Hotel Avante (Wired), Wild Palms Hotel (Fast Company), Hotel Los Gatos (Town and Country), and the Water's Edge (Yachting). Obviously your inspiration doesn’t need to be a magazine, it can just as easily be a song, a group of words, or just a particular image. Find something that resonates with the customers you have in mind and design your store to reflect that vision.
Skoolies do have significant drawbacks, however. Their size makes them a bit unwieldy to drive, and getting to some of the more out-of-the-way camping spots just won’t be an option. If something goes wrong mechanically, it can be much more expensive to fix than a normal vehicle. Also, the sheer size of these vehicles means the gas mileage is much worse than other options.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Whether you plan to go it alone or hire a professional, there are many resources available to help you plan and execute your retail store layout. If you don’t feel comfortable tackling the project yourself, a professional retail store planner, interior designer, or display designer can turn your dreams into reality. Or if you want to handle it all yourself, store planning software and other online idea resources can make the job easier.

We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
The kind of apps that fall into this app type are extensive. Facebook, Instagram, Snapchat, Twitter, WhatsApp, Pinterest, and YouTube are all examples. Remember that some of these apps have been worked on for many, many years. Thus, a v1.0 social app or social networking app will likely not offer all of the same features. For instance, Snapchat did not start with videos, filters, or their "Stories" functionality. A social app would, however, include user authentication, friending, favoriting (or other data interaction), some sort of messaging, and comparable "baseline" functionality.
​In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts.  Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up.  A more economical approach would be to build your jigs as your projects demand them.  After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
A great supplier will provide the raw ingredients of your success — often literally. What’s more, they’ll deliver them on time, every time. And they’ll always deliver exactly what you ordered, no more, and no less. A large part of the process of inventory control is ensuring that you are paying for exactly the inventory that comes through your door, and not a penny more. Even great suppliers, however, are looking for the highest price possible for their goods, so once you find them, make sure you’re ready to negotiate!
For the large square windows near the tailgate I just used those big “magic auto shades” like these, which fit perfectly to cover up those side windows and the back window by the tailgate (I had four in the canopy) and another set up in the cab for my actual window. As for the longer side windows I just used a USPS box, haphazardly stuck up against the window. Nothing fancy.
Having a deliberate store layout is important for maximizing revenue for brick-and-mortar retailers. By setting a plan, retailers can strategically direct shoppers to high-priority products and drive impulse sales. An effective store layout also makes the space organized and easy to navigate, which is important for providing a good customer experience.
There’s a reason why some of the biggest players online have names that are essentially gobbledegook: Zappos, Skype, Zynga. While there’s certainly some psychological naming principles that often come into play, at the most basic level, it’s simply easier to find this space online and then strive to own the brand name in the minds of consumers. How important this will be to your small business will depend on a number of variables, including your intended size, location, and your desire to exploit ecommerce as well as a local brick-and-mortar business.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
In our opinion, having one of these is an absolute must for living on the road - especially in humid areas. To fully cover the width of a van’s side doors/back doors, you’ll need a larger screen that’s designed for French doors. If your vehicle has a smaller door opening like an RV, a screen meant for a standard door will work fine. We could only find standard door screens, so we bought two and hot-glued them together to cover up our side door.

Apps begin to get more complex—and costly—once user authentication is involved. The main reasons for that are all the other expectations that come with user authentication. Typically, they include interacting with data (e.g., favoriting an article), syncing data across devices, push notifications, and perhaps collaborative features (e.g., inviting a family member).
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
There you have it! Now you have no excuses, you must start planning right away. Please remember this can take a lot of time and a lot of work, so be sure not to stare at your task list in its entirety too often. I don’t want you to get overwhelmed knowing all the things you must get accomplished. Just focus on the goal that is the most important and attack it, task by task. Need help organizing these goals? Check out my Goal Planning Worksheets here:
Hi thanks for the info. I’ve got a 2009 tacoma and went with a simple, no screws elevated system. I’ve also got a mx series ARE shell with rack rails so I’ll probably take too much stuff now. Oh well. My question is: how did you attach the plywood to the life gate? My carpentry/construction skills are best illustrated by the “Homer Simpson spice rack”. You used the existing holes in the tail gate, but did you put the tail gate cover back on the tail gate and put the plywood over it and screw thru both or ditch the cover? Thanks

If you want the ultimate vehicle to customize for your DIY van conversion, the Sprinter is the van for you. They have enough headroom even for tall people to stand up, and enough interior space to design any kind of layout. They also typically have diesel engines, which means greater fuel efficiency and engine life (many diesel Sprinters have been known to make it past 400,000 miles). If you think you’ll be doing a lot of off-roading, the Mercedes Sprinter also comes in a 4x4 version.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
I will also typically secure those sorts of items under my locked platform if I am gone for a few days in the backcountry, because in reality I could probably care less if someone broke in and stole my box of food, versus someone who stole my clothes or expensive down jackets, which would be much more problematic (and costly) to replace on the road.
Great instructional! I built the bed of my 92′ Toyota pickup ext. cab the same way you did. I did some hard searching and found this camp pad, which literally fits the 40″ wide sleeping space perfectly. A few different mats from Exped will fit, but here’s the one I bought. Just thought you might like to know there’s an inflatable duo sleeping pad out there that works for your setup!
With all the time and effort you've put into properly merchandising your products, the last thing you want is for incoming customers to hurry past them — this ultimately limits the number of products they'll purchase. One way retailers combat this is through creating breaks that force them to pause. These are sometimes referred to as "speed bumps." Essentially, this can be anything that gives customers a visual break and can be achieved through signage or special/seasonal displays.

High-velocity fans are also an important tool in their own right, particularly at your finishing station. Increased air flow will help dissipate fumes from paints and sprays for your safety, and you can train a fan on your project to help paint dry more quickly between coats on humid days. To get the most out of your fan, look for floor fans that are easy to aim or wall-mounted fans that will save space in smaller shops.
Calculating the size of your desired parking lot is easy. The rule of thumb is to have a parking spot for every three customers. Determining traffic is trickier and potentially more lucrative. To help, we wrote an article on how to calculate your desired foot traffic. If you want to calculate your desired vehicle traffic, you can refer to our article on how to choose a location for your restaurant.

To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
Power outlets are also needed for lighting, heaters, AC units, radios, televisions, CNC machines, 3D printers, and computers—all of which you’ll find in many workshops (although maybe not together, and maybe not all in your garage.) You simply can never have too many outlets and it’s much safer to have too many than not enough. Bring in an electrician to help install your outlets and setup 220v power if needed for larger shop tools.
Boy you guys are spoiled, lol. There will always be at least some echo in the shop. I wouldn’t judge the acoustics based on this video though since the shop was still being put together at the time. No cabinets and no floor tiles, so the echo is to be expected. Have you seen the latest video? http://www.thewoodwhisperer.co.....rock-star/ The sound is dramatically improved over the Dream Shop video and all I did so far was add a few floor mats here and there. By the time the cabinets are in and I get some nice rubber floor tiles in place, the sound should be at least to the level of the old shop if not better. Right now though, my priority is on building a bed and I do consider the current sound to be “acceptable” for web videos. I’ll focus on tweaking things when I finally get some spare time. Considering adding some acoustic tiles to the ceiling.
The subfloor provides a stable layer - basically a sheet of plywood - for your floor to sit on. You’ll see a lot of van build videos on Youtube showing a ¾” subfloor, but that thickness just isn’t necessary in a van. The thicker the subfloor, the higher the cost and weight, and the more valuable interior space it takes away. We recommend using ¼” plywood for your subfloor, which is plenty thick enough for a van.
As Kizer & Bender always tell retailers: Put it on paper. If you haven’t settled on your store layout—or even if you have—the first thing you need to do is work your plan out on paper before you start moving things around in your store. Putting it on paper helps give you a clearer picture of the desired result and any potential issues before getting started. Remember, many small retailers find that a mix of floor plan and layout styles works best.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
I have been working on building out the space, starting with a new welding table and small material/saw rack. I was able to dedicate a 20' x 28' area to fabrication. I need to figure out some things like angle grinder storage, fume exhaust hood and cold saw set up, but I will get there. Power is one nice thing with a 400A 208VAC 3ph supply panel. Also got the compressor in a sound dampened closet with cooling so the noise level is down significantly. Oh ya, dedicated 15 ton AC for the shop has been nice.

Since grid layouts are used in most grocery, big box, and convenience stores, they create a familiar feel to customers. However, due to this familiarity, they tend to impart a grab-and-go experience. A grid layout can be a good choice for small retailers who shelf-stock inventory in quantity, like toys, books, magazines, specialty foods, kitchenware, and home goods. However, it’s not ideal for retailers who want to create an upscale, branded environment that invites relaxed browsing.
The kind of apps that fall into this app type are extensive. Facebook, Instagram, Snapchat, Twitter, WhatsApp, Pinterest, and YouTube are all examples. Remember that some of these apps have been worked on for many, many years. Thus, a v1.0 social app or social networking app will likely not offer all of the same features. For instance, Snapchat did not start with videos, filters, or their "Stories" functionality. A social app would, however, include user authentication, friending, favoriting (or other data interaction), some sort of messaging, and comparable "baseline" functionality.

For small business owners, these tools present an incredible opportunity to set smarter business goals and easily identify some of the key factors of success and growth in their business. However, when you couple the breadth of technology options with decisions about basic store and restaurant equipment, such as espresso machines or air conditioning units, it can become a little overwhelming to figure out what is actually worth the investment.
Ok Rob let me try again .I would suggest you sign up for a community collage woodworking class or a woodworking coop where you can use the tools you will need to build the kind of items you have in mind. You say you have used the tools you listed but that could mean only used them once or twice. If you have minimal experience with tools and woodworking that might be another reason to take a class assuming there is one available . Do you have a space you can use as a shop ,a garage,carport etc? As far as tools and equipment are concerned I think Knotscott covered it very well. I know your supposed’s said you couldn’t find tools on Craigslist or garage sales but those might be the place you can make an offer on a shop full of tools in the price range you trying to stay in possibly with some materials and other extras. It might even work to put a wanted wood shop full of tools in the tools section of your local Craigslist.
Whether you end up looking at self-checkout counters, fancy lighting systems, special refrigerated cases, or any of a countless number of options, never forget that these are only tools to help accomplish your main goal. Your store needs to create an environment where customers want to be, where they feel comfortable and appreciated, and where that experience will prompt them to purchase (and hopefully encourage their friends to do the same). Equipment and technology decisions should always be made with your customers in mind.
We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.
×