I don’t own a dog, but I have taken my buddy’s two dogs out with us to the trailhead at least. Not sure that I have great recommendations for how you would go about living in the truck with your dog. All we really did was lower the large wooden deck to the bottom position, throw down some soft doggy beds and pillows, then cover it all with a giant blanket which also covered like the side bins to keep dog hair from getting all over. It was nice and cozy for the dogs while driving down the road. Then we just put packs and other gear on/in the side bins. We used some big metal clamps to secure the blanket to the side bins and keep it from falling down or sliding around. I would think avoiding any carpeting would be a good bet, just go with blankets and things than can be taken out, cleaned, and you can sweep out the back.
Let’s face it, one of the most significant costs of your shop will be its foundation. While you’re at it, what about adding space above your shop? There may be regulations preventing you from building living space above your shop if it is in an urban setting or in an outbuilding, but there may be some flex­ibility depending on where you live. It is in the municipality’s interests to encourage infill housing that uses existing infra­structure. At a minimum, think about including attic trusses to create some space above your shop for drying lumber or storing equipment. Access could be from simple pull-down attic stairs or from the exterior if you don’t want to lose floor space to a stair or ladder. If you’re creating an addition to your house, you may be able to add a couple of rooms you’ve always wanted, such as a family room, office or in-law suite.
Thanks! Yep, the canopy clamps and the grooves in the bed liner are the only things holding the side shelves and sleeping platform in place. You just pop off the clamps with a ratchet and the whole things lifts out / slides out easily. That’s what I did to treat the wood after construction, takes maybe 15 minutes to pop out. Very modular. It’s been in there for more than two years now, same wood, and everything is still looking good and working fine. I like it!
These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
Like most things in life, we believe that entrepreneurship can be learned, you just have to be willing to put one foot in front of the other. Aftering reading How to Start a Small Business 101, you’ll be equipped with the essential tools and resources you need to succeed at planning, raising capital, and executing crucial day-to-day business operations.
It might sound harsh, but when starting a small business your online presence is crucial. If you speak to some experienced local business owners, many will denounce the existence of online review sites like Yelp and Google Local. They’ll tell you about the added time and pressure they now face to maintain social media profiles for their businesses. A lot of local entrepreneurs will share their bad experiences with online daily deal websites like Groupon. But all that complaining doesn’t change one established fact that the internet isn’t going anywhere.
Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
The final size I decided on was 1800 sq. ft. Yeah, that’s big! I actually balked and second guessed myself after we received the estimate from the contractor. Sure, more space is nice, but at what cost? I then asked for a second estimate, bringing the shop down to 1500 sq feet, which is still huge. As you might expect, the savings just weren’t that substantial. By the time you get over 1000 sq. ft., the price per sq. ft. is really low, making it very difficult to justify down-sizing. So I bit the bullet and stayed with my original choice of 1800 sq. ft.
When you’re first starting out, it can be hard to imagine that there are entrepreneurs out there complaining of having grown too fast. But for some, it’s not a problem that’s welcome. For every Ben and Jerry’s, (Ben Cohen and Jerry Greenfield turned a rundown Burlington, VT gas station into an ice cream empire), there’s a Zynga or a Living Social that has enjoyed incredibly fast-paced growth, let their operating costs get out of hand, and then had to engage in mass layoffs when reality hit. If you’re enjoying fast-paced growth, make sure that this is reflected in your operating margins, not just the metric of revenue. You don’t want to be the butt of the old retail joke: “We’re losing a buck on every sale, but we sure are making it up on volume!”
Can you outfit your shop with all the necessary hand tools for just $100? Christopher Schwarz says you can, and he’ll show you how to do it in this article. Take Christopher’s shopping list to the flea market and come back with everything you need for less than you’d spend on one new hand plane. You can do all your woodworking with hand tools, and this article from Popular Woodworking will equip you with everything you need.
If you want the ability to cook inside your van but don’t have a whole lot to spend, your best option is the Coleman Classic propane camping stove. For about $60 you get a sturdy and reliable 2-burner stove that runs off of replaceable 1-lb propane canisters. We’ve seen many people using these out on the road, and they do the job very well. Coleman has hardly changed the design of these stoves for decades, so you know they’re doing something right.
Whether you build or buy your workbench, it must be designed and constructed to withstand the rigors and pounding you’ll put it through. The base and legs should be sturdy and the table should not easily be knocked over. The top should be durable and not easily dinged or dented. Make sure your workbench is made of a material appropriate for your types of projects, too.

Ryan, I have the same (almost) 90’s Toyota Pickup and love it! this is so helpful, and I will definitely be using this method. my main concern is that 1/2′ plywood sagging. do you notice it sags quite a bit or does it mostly hold up? my thought was to build the vertical bins a little wider, so that the plywood bed platform wouldn’t be under so much stress. the second issue im running into is wrapping my head around trying to organize and compartmentalize things appropriately. what do you typically put where so it is easy to reach and use?
I know in Missoula the garbage men do not like unbagged dust chips. They sent my friend a warning notice in the mail. Do you pull your drum out to the garbage and let the dust fly or dump it into a bag? My friend has garbage cans with 33 gallon liner which he pulls out of a sealed dust collection box beneath the cyclone… then he uses a hand truck to haul it out to the alley and then puts a fresh can in the box. It seems like a simple dust management method by not handling the dust by either scooping or dumping it out into a bag. I am always trying to think of ways to have less contact with harmful dust particles and I am curious as to how others handle the situation. Have a great weekend!
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.
Whether you build or buy your workbench, it must be designed and constructed to withstand the rigors and pounding you’ll put it through. The base and legs should be sturdy and the table should not easily be knocked over. The top should be durable and not easily dinged or dented. Make sure your workbench is made of a material appropriate for your types of projects, too.

Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.
I used your set-up as a guide in building mine. It is a little different – it’s shorter a little bit, as I have a shorter canopy cover and I didn’t make the sleeping platform flush with the walls of the truck bed – but it turned out great! I’m really happy with it. Also, one of my favorite parts about it is none of it is actually attached to the truck. So I can take everything out and it makes cleaning a little easier. I’d post photos if I knew how. If you feel like seeing it let me know and tell me how to get them to you!
The core criteria of small business site selection will always be foot traffic and ease of access. In places like New York City, this means being by the subway or on a busy street. But for most of America it’s about considering traffic flow and parking accessibility. Ever see three gas stations at the same intersection? They are all picking off different traffic flows because they know customers are looking for the shortest possible detour.

After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.
Ultimate Small Shop offers a comprehensive guide illustrating how to set up a workshop. It may be just a small basement shop or a part of the garage converted into a workshop. The guide lays out all the steps and actually caps the investment at under a thousand dollars. Woodworkers can build their workshop for less than $1,000. This does not entail any compromise of tools or the scope of woodworking projects. The guide provides a shopping list including the best tools and there are exact links to find those tools and buy them at the best prices. There are floor plans to ensure layouts are optimized even in the most cramped spaces.

Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
The kind of apps that fall into this app type are extensive. Facebook, Instagram, Snapchat, Twitter, WhatsApp, Pinterest, and YouTube are all examples. Remember that some of these apps have been worked on for many, many years. Thus, a v1.0 social app or social networking app will likely not offer all of the same features. For instance, Snapchat did not start with videos, filters, or their "Stories" functionality. A social app would, however, include user authentication, friending, favoriting (or other data interaction), some sort of messaging, and comparable "baseline" functionality.
A software engineer needs to know how to code.  An administrative assistant must answer phones and organize paperwork.  But a marketer typically needs to wear many hats, from writer to advertiser to strategist.  And unlike other job roles, marketing employees can affect the core of a business by changing the way it’s positioned — and they can be held accountable to the company’s bottom line.
Hey Brett! Awesome to hear that your own plans are coming together. I can’t really recall seeing any dirtbags rolling around in a Pruis… I wouldn’t imagine it to be the ideal vehicle for transporting gear and living out of, but the gas savings would really add up over 6-7 months on the road. In general, I’m in favor of going with what you’ve got and finding creative ways to make it work. Maybe you can add a rooftop box? On some vehicles, people even remove the passenger seat(s) for extra storage space. The biggest problem with the Prius that I see would be finding a place to sleep while you are on the road… But I guess that’s where your gas savings and cheap hotel would come in. I know Gina Begin has been living in her little car for a long while now, check out her stuff, and maybe reach out to her. She’s a veteran at dirtbaggin’ it in a car: http://www.ginabegin.com/2013/05/the-ultimate-guide-to-living-on-road-15.html
Now this Super Pencil from C.H. Hanson does all of that and more. The entire pencil is made from a non toxic graphite composition so the whole thing is a writing surface with no wood around it to shave away. Super pencil marks are water and smudge resistant and because the composite is so durable it never needs sharpening even when you use it on rough materials like concrete.
At a certain point, you may decide that it is time to move on from your business. Whether you’re winding down a business that just didn’t work out, retiring (and maybe opening that beach bar in Belize), or cashing in on the effort you’ve put into creating a lucrative enterprise, you will hopefully have established your end goal well in advance so that the time to strategically exit will be clear.
When we published our massive review on how much an app costs back in 2015, we had no idea it would become the top resource on the web. Two years later, that piece is still considered the definitive resource for app development costs in our industry. It’s because of its popularity that I feel compelled to revisit this subject. Additionally, doing so will allow for some fresh perspectives based on what's changed in the app industry as well as another way to look at the topic.
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.

It is particularly important that you think about your customer’s experience holistically. Big-box retailers have long understood that people have five senses and that those senses affect decision making in a profound way. Whether it’s through intelligent lighting, the right music selection, or the careful piping in of a beautiful scent, smart retailers have learned the art of manipulating customer mood — whether they need you excited about a sale or relaxed and in the mood to hang around.

Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Marc, I enjoyed the video. Thank you for sharing your dream shop with us. I would be interested in seeing a demo video on your Clear Vue cyclone dust collection system. Which one did you obtain & what type of duct work did you use (seamless?) Do you plan on enclosing the unit in a closet to reduce noise and keep dust confined? Do you have to purchase special expensive plastic dust bags for the drum? Is it hard to pull the bag out of the drum for trash collection? If you could address these questions in a demo video I would appreciate it. Oh, perhaps you already have one …. I will check out your video archives. Thanks again and keep up the great work!
WOW that is a nice size shop! I am looking forward to more videos on the shop projects! We have been shopping for a house for over a year & have finally found one but it has nothing for me to use as my woodshop! I currently have a basement shop that’s 24×40 & it’s really huge for me I couldn’t imagine any bigger. Anyway I will be looking at building a new woodshop for myself (yes I am a female woodworker) & you have given me lots of great ideas so far. I am an Artist & wood is my preference, everything I make is quite small (no furniture or anything that big) but I have lots of specialty tools for what I do as well! Thank you for sharing your ideas & all that you do. Keep up the great work!

Remember the social media networks we asked you to secure in section five, Choosing a Business Name? Well, now is the perfect time to activate those channels. Use social media to build excitement about your grand opening and keep potential customers informed about special promotions and sales. People want to know what makes you special, so tell them why your store or restaurant will be different to what is currently available. From sharing pictures of that new fancy espresso machine or sneak peeks of your store’s interior, you can gain buy-in to your central message and build some anticipation before you even open your doors. Knowing how to to leverage key social channels is imperative to starting a success small business that will stand the test of time.
My husband is always hounding me about wearing eye protection whenever I use power tools. (Admittedly, I could be more diligent about it.) So, he recently glued some small magnets to several pairs of safety glasses and stuck them on all the power tools in our garage that have metal housings. Now it’s fast and easy for me to grab the glasses when I need them, and I’m reminded that my husband loves me. — Lisa Yanda. Here’s the other must have safety gear every DIYer should own.
If you dream of devoting your life to a cause you believe in, it might be time to start a nonprofit. You’ll need to incorporate your business and file for 501(c)(3) tax-exempt status -- and then you’ll be required to meet ongoing standards of compliance, but the payoff is making a meaningful impact on a cause you believe in. Want to do good while still making a profit? Consider social entrepreneurship.
If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”
Most workshop tasks require good ventilation, and that’s something garages are generally poor at. Plus, passive ventilation (like opening a window) usually isn’t enough. A ceiling exhaust fan is a good start but if you are serious about keeping things clean then your ultimate workshop should also include a dust collection system, central vacuum and air ventilation system. All three of these systems will keep the dust, dirt, and other heavy particles off your clothes and out of your lungs which makes for a safer work environment.
The nomadic truck camping lifestyle has been incredibly freeing, not only is cheap and accessible to most anyone, but it can take you beyond places you even imagined. One book that I’d recommend to all newcomers to this lifestyle is Bob Wells’ How to Live in a Car, Van, or RV, which will help you better understand the ins and outs of this lifestyle.
×