That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!

As Kizer & Bender always tell retailers: Put it on paper. If you haven’t settled on your store layout—or even if you have—the first thing you need to do is work your plan out on paper before you start moving things around in your store. Putting it on paper helps give you a clearer picture of the desired result and any potential issues before getting started. Remember, many small retailers find that a mix of floor plan and layout styles works best.

Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.


It’s hard to overstate the importance of choosing the right location when starting your small business. We’re sure you’ve heard the saying 1,000 times before, Location, Location, Location! Some of the world’s most well-financed franchises have this weaved into their business DNA. McDonald’s Ray Kroc is the perfect example. When asked about the business, this well-know American businessman and philanthropist once stated, “We are in the real estate business, not the hamburger business.”
Hello! My name is Donna Jean. I love to read books and my job is to write a daily review of all the novelties in the world of eBooks. I allow only the best of them to be published on my website. I really hope to make our world more bright, beautiful and kind. You can participate by downloading any book from my site, and you will receive health, luck, kindness, and love, which will support you during all your life. Wishing your dreams begin to come true, and every tomorrow be happy for you. Thank you! ❤❤❤
I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.
However, there are some downsides. If you want to customize the interior you’ll have to completely gut the entire thing, which can be a lot of extra work. The weird shape and fiberglass construction of most high tops also make it more difficult to install solar panels, a ceiling, or anything else on the roof. And we’ve also found that some auto repair shops aren’t tall enough to put our van up on a lift - though that’s only really an issue for major work, not routine maintenance.
I get all the zen I need from Dunkin Donuts. :) Actually, I am reserving judgement concerning sound at this point and here’s why. I worked in a 1000 sq ft shop for the first 5 years of this show and never had any echo complaints. That was with 16 ft ceilings. The new shop was pretty unbearable to talk in when it was empty and became quite tolerable when filled with the initial equipment. With the addition of the floor pads and cabinetry, I am pretty confident the echo will be reduced fairly close to the previous shop’s level. If not, I’ll have to consider my options, because there’s no way I’m hanging drapes in my shop, lol.
Different approach in that they hung one end of the sleeping platform with hooks and U bolts. One of the best write ups with full details about rigging up an electrical system with second batteries and an isolator, as well as using power inverters. They were then able to incorporate cool things like a mini fridge, lights, and mini PC fans for air circulation.
You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.
In my opinion, the best shop space is a flexible one. I know many folks expected that after setting up my shop so many times, I would be able to design the PERFECT shop space including a finishing room, a dust collection closet, and even some internal walls. But the truth is, the most important lesson I learned over the years was to expect change. My shop is not a static entity. It is more like a living breathing creature that adapts, evolves, grows, shrinks, and changes configuration. Committing to an internal spacial arrangement too early could yield disappointing results. This is why you won’t see me placing dust collection ductwork in the floor. I need to work in a space for at least a few months before I can be confident in my initial setup. Even then, I fully expect things to change at some point. If I made too many restrictive and/or permanent decisions ahead of time, these changes could be difficult or impossible to implement. So my best piece of advice is to forget about the concept of perfection. Instead, focus on flexibility. The ideal shop, in my mind, is little more than 4 walls, a roof, and a butt-load of outlets and lights. So here are some of my basic general goals for my new shop space.

Concrete garage floors can work as a workshop surface, but over time they stain and you’ll end up tracking a lot of dust and dirt into your home. An epoxy floor finish is easier to clean and can also provide extra grip. For a softer surface that will help your joints when standing a long time, check out those restaurant grade rubber floor mats or some durable options that include garage floor tile.


The first thing to understand about a business plan and financial projections is that the process of compiling them is often more important than the final product. Sure, the actual sheets of paper, filled with spreadsheets and graphs with pretty arrows pointing up and to the right are great — and can be very important in helping you to secure funding — however, when it comes down to the brass tacks of starting a successful business, it’s the process, not the paper, that counts.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
If you are looking to sell your business, it is important to engage a lawyer who is a business specialist to ensure you gain the best possible valuation. A small business is valued by assessing the potential ongoing income from the business over the coming few years. Normally this means that a business will be valued at three to five times net revenues, which can present a potential issue for particularly tax-savvy small business owners. Remember that every time you write off an expense against your business, you are lowering the net margin of the business. So, that dollar you saved by writing off the expense could cost you three to five dollars on the valuation of your business.
If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based busi­nesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of run­ning into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibili­ties that your property will allow.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
After looking at a number of spaces that are available to lease, you may start to wonder whether it’s better to buy or lease commercial real estate. Of course, there are occasions when it might be better to purchase commercial real estate rather than leasing it. For example, if you buy a commercial space, you’ll take advantage of equity, depreciation, cash flow, and asset appreciation.
There seems to be two things I like looking at and they are work benches & work shops. I too use my work shop for several other activities. I currently have a basement shop with a walk out entry, which is roughly 340 square feet and shaped like a flat s and has less than 8' ceiling height. In that shop I have an old Unisaw w/50"fence, 8" jointer, 15" planer, 10" sliding compound saw, 14" bandsaw and various & assorted power & hand tools. Also in the same space I have a small closet, dog grooming tub, & a space where a bathroom was roughed out. It is far from finished space and I have plans to put up a ship lapped paneled walls and fix up the closet for tool storage. I also plan on putting a cyclone in the bathroom space along with a tolet. I can work in the space as it is pretty well but the studded walls, insulation, & dust make the space somewhat uninviting.
Assembling parts is easiest when you can work at a comfortable height. But the height of that working surface depends on the size of the project. These ABC boxes, so called because they’re made with sides of three different dimensions, make a variable-height assembly table base. By rotating the boxes or standing them on end, you’ll get three different working heights.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but out­side the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials move­ment. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
It’s no accident that some of the best marketers in the tech startup industry are known as “growth hackers.” Think about your target demographic (e.g. students, local mothers, teenagers) and find any way you can to get the word out to them. Email mommy bloggers, hand out free samples at the local college, or write your website on all the napkins you hand out with your food. There is no substitute for action.
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
At times, while you are starting a small business, it will seem like there is a brick wall in front of you, made up of all the different problems that will occupy your time and mind: a lack of funds, permits, regulations, tax worries, inventory issues, or a lack of customers. Concepts like “free time” and “the weekend” will take on a very different meaning. While the emotional ups and downs of cash flow management and customer service, may drain your will to live.
Hey Melody, thanks for the email. I’ve traveled through some extremely humid areas (Central America)… I’m taking it that your canopy does not have a headliner? That in and of itself helps a great deal. Personally I would be hesitant to put holes or van roof vents in my cap, but that may be what you want to do. I would try sleeping with a portable personal fan first and see how that helps with the condensation issue. For me it worked wonders while sleeping in those hot and humid environments. I ran mine off the inverter connected to my secondary battery.

Another great source of store design inspiration is your product vendors and their line reps. After all, your success is their success, so they’re usually happy to share store design and merchandising ideas. Many provide retailers with free or low-cost branded display units, too. Some line reps will even assist you in product mapping your store, display setup, and replenishment. It never hurts to ask!
Ultimate Small Shop is a turnkey solution for woodworkers to get started with their dream workshop. Every woodworker, hobbyist or professional, wants a nice workshop in their home. It may be the garage or a shed, the barn or a detached man cave, the basement or a room up somewhere with enough space. Woodworkers often fail to create their dream workshops due to dearth of space and funds. Ultimate Small Shop solves both these issues and empowers woodworkers to live their dreams.
To help, I’ve pulled together 40 small business ideas for anyone who wants to run their own business. Use these as a jumping off point to spark your own unique ideas.And if all else fails, live the words of Airbnb Co-founder Brian Chesky: “If we tried to think of a good idea, we wouldn’t have been able to think of a good idea. You just have to find the solution for a problem in your own life.”

Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us.
I think it would work pretty well for a music festival, I don’t see why not. I wouldn’t say it is robbery proof, but generally robbers are looking for quick and easy targets, like a purse sitting on the front seat, just smash and grab. If someone really wanted to rob what was under they platform, they surely could, but they’d need more tools and more time to do so. And they don’t even know if there is anything good under there… I’d like to think of it as a really good robbery deterrent.
Well, my workshop is finally complete and I’m ready to take on just about project that comes down the line. And I’m pretty well set up here. I’ve got a great workbench, plenty of table space over here that easily rolls around the shop if I need it, lot of storage space down here, I can tuck these tools away or bring out any new ones that I need. And as you can see I’ve got plenty of supplies to tackle just about any project.

The on the go mode is ideal for when I’m just driving all day and need to pull over and get some rest, be it in a parking lot, a residential cul-de-suc, or wherever. I usually toss a couple of items in the cab of my truck and crawl into the “coffin” sleeping arrangement for a quick night’s rest, but I can also crawl in without placing anything in the cab.
×