Hand tools offer your best chance of finding a real bargain. Until the early 20th century, nearly all woodworking was done with hand tools, and their designs and uses have changed little. Most of the high-end planes on today’s market, for example, are just reproductions of the original designs. And because the originals were mass-produced, they are fairly easy to find at rummage sales and antiques stores. (For more information, refer to Matthew Teague’s article, “Buying Old Tools,” in FWW #180).
Boy you guys are spoiled, lol. There will always be at least some echo in the shop. I wouldn’t judge the acoustics based on this video though since the shop was still being put together at the time. No cabinets and no floor tiles, so the echo is to be expected. Have you seen the latest video? http://www.thewoodwhisperer.co.....rock-star/ The sound is dramatically improved over the Dream Shop video and all I did so far was add a few floor mats here and there. By the time the cabinets are in and I get some nice rubber floor tiles in place, the sound should be at least to the level of the old shop if not better. Right now though, my priority is on building a bed and I do consider the current sound to be “acceptable” for web videos. I’ll focus on tweaking things when I finally get some spare time. Considering adding some acoustic tiles to the ceiling.
I would definitely stick with the vapor barrier under the floor to avoid moisture from breaking up the OSB. try to build the base high enough to keep it dry and allow airflow to dry it out under there. FYI I recently repaired a neighbor's shed roof that must have been partially repaired before with plywood. The OSB was fine under the shingles, but the plywood was wrecked due to moisture. I would stick with OSB. Since you live here in NOVA, details will be a little more helpful to you. I really can't use the shed in the summer without the AC on. It gets direct sun and gets up to the 90's in there with out any air movement. I am planning on eventually lining the inside of the ceiling with that thin reflective insulation to bounce back some of the heat.
Now also we have some shelves that we built here above this, little cubicles like this work great to organize your workshop so you can have different tools or different supplies in the different little areas. And we’re about to install a very simple countertop. Now this is nothing more than just three-quarter-inch plywood and we decided to stain it instead of painting it, because you know it’s going to take a lot of abuse with all the pounding and the dings, and dents you’ll get in a workbench so staining it and then sealing it with a coat of sealer will probably hold up better than anything else. Now we’ll put another coat of sealer on it after we finish the front edge band and the backsplash and once all of that is complete, boy this thing is going to work nice.
I have a plastic bed lining on my truck, which also covered the back of the tailgate… I just popped the screws off, took off the plastic liner and drilled holes in the sheet of plywood to match those used by the plastic tailgate cover. Sorry if that doesn’t help you with your setup. But I’m sure you could just drill your own holes in the metal tailgate. Use the plywood cover as a guide for your screw holes…
If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.

The key to success here is having clear processes written down, promoting from within whenever possible, and remaining open to change. You’ll want to balance your desire to educate your manager on how to manage your business with an openness to feedback and new ways of doing things. You’ll also want to take advantage of the technology available to keep you abreast of things like real-time sales data for all your locations, no matter where you are.
I have a question, you mention what a problem it would be if the cinder blocks were to sink yet you have installed them with the least amount of footprint on the ground. Was there a reason for this? I would have installed them with the flat side on the ground, and I realize they would not hold as much load as the way you have them but considering the number you have used, the spacing, and the size of the shed, load should not be a problem. Just wondering.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
Store design experts agree that this area should be open, inviting, and free of overpowering displays and signage clutter, as shown in the image above. Many customer behavior studies, including those conducted by Envirosell’s Paco Underhill, support this opinion. They show that customers tend to ignore displays, signage, and even manned sales counters placed close to store entrances.
Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.

People tend to buy cargo vans for work and hold on to them for years, so many vans on the market can be pretty beat up. Although you can find inexpensive cargo vans in good condition, it can be tough to find anything with lower mileage - so be prepared for all that comes with owning a higher mileage vehicle. Cargo vans also don’t offer much headroom. There’s no way even shorter people will be able to stand in one, and the lack of headroom also cuts down on storage space.


Starting your own small business can be an incredibly rewarding experience both personally and financially. However, like anything worthwhile, it takes a great deal of time and effort to be successful at it. Your results will depend on how much you are willing to apply yourself. The lessons in How to Start a Small Business 101 are designed to give you a leg up on the competition so you can hit the ground running. Now all you’ve got to do is bookmark this page, free up some time, grab a cup of coffee, and start making your way through each section.
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
SBA provides support and tools to aspiring small business owners and in particular to minority-owned, women-owned, disadvantaged, and veteran-owned businesses, including a government-backed financing scheme to qualified participants. Local and state authorities also have a range of programs designed to encourage the growth of your small business. Make sure to research your local authority’s website.
To avoid buyer’s block, define the core characteristics you absolutely need in your business. Write them down in a prioritized list ranked from ‘deal breaker’ to ‘would be nice to have.’ Now cross off the bottom five and focus only on the ones that are left. Compromising is essential in choosing a commercial space, especially in popular neighborhoods. Besides, you’d be surprised how what once seemed like a less than stellar storefront can become your dream location once you get those creative juices flowing.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
A dust mask or respirator will protect you while you're working, but won't do anything to protect you or your family from suspended particles still in the air. For this reason, an air filter is an absolute must if you work with woods indoors (I know of guys who sneezed out sawdust after working too long without an air cleaner). It's possible to make your own air cleaner out of box fans and furnace filters, but retail air cleaners will usually be much more compact. If you go that route, we recommend Wen 3410 3-Speed Remote-Controlled Air Filtration System for smaller shops.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.

Well, I thought about that I don’t want all that dust to kind of infiltrate everything else in the building. So actually instead of putting in some kind of dust collection system, I thought that I would probably just put a nice shop vac here. And then I have room that I can bring some hose back behind this column and then you know if you’re sitting here working on something we can have adapters that go right into a miter saw or right into a sander or have a little outlet more or less to lay up on the counter that would collect all of the dust. And the same thing could happen on any of the work we do out here.

Workers’ compensation insurance is designed to provide wage replacement and medical and death benefits to employees who are injured or worse on the job. In exchange for these benefits, the employee gives up his or her rights to sue for liability leading to the accident. Your premium will reflect the type of business you operate and the average salary of your employees. Much like auto insurance, business owners who are new to starting a small business or those with less experience tend to pay higher premiums.
Both kids and adults have sat inside [the Optimus Prime truck] and been brought to tears. For many, it is a dream come true. Some kids are very intimidated by Optimus Prime because of the size and won’t go anywhere near it. But I love making people smile. The fact that I can make them smile for just a few minutes by seeing Optimus Prime on the highway means the world to me.
Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.
These new companies no longer charge crazy upfront fees, moving instead to what’s known as a “SaaS” monthly subscription model, often with a free trial period. Therefore, the risk of trying a new product is greatly reduced, as you are required to pay little or nothing upfront. Even Microsoft announced in 2015 that they would be moving their flagship product, Microsoft Office, to this pricing model.
Once you’ve got that, you’ll want to familiarize yourself with your tax obligations as a employer, including providing required employee benefits such as social security and workers’ compensation. As an employer you are also responsible for withholding federal and state taxes from your employees’ paychecks. What’s more, you are obliged to ensure all withheld tax is forwarded to the government within a defined time frame (usually a matter of days after the paycheck was issued). Failure to do so can result in a fine.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
I framed in a 4x8 Garden Shed on the back.  I didn't want it so deep that stuff would get buried in it.  I need to take an updated picture of the back.  These pics were from early on and I have changed some things in the organization.  I used similar framing techniques and built a lean to roof attached with metal hangers.  I chose to use clear corrugated roofing to allow natural light into this shed.  You can see the 2 shopvacs that were originally part of my simple vacuum system.  I have removed them and found that I get better airflow using an electric leaf blower with the vacuum attachment hooked up to my system.  There is a large metal trashcan with a dust collection separator to collect the larger pieces of saw dust and chips.  My air compressor is on a shelf on the right now and I ran a hose through the wall and to a 25 foot reel attached to the ceiling.  I wired separate switched for both on the inside of my shop.  These systems work extremely well for a small shop.  The wall provides some insulation from the overwhelming noise they would otherwise create inside the shop.
The biggest problem I see with business owners and goal planning, is that they know they goal they want to accomplish, but they don't know the steps to accomplish them. Sound familiar? Well welcome to the life of an entrepreneur. We are usually trying to figure it out as we go along so don't worry. Here are my most favorite resources to help with figuring out the steps to accomplish anything on your goal sheet:
We've also chronicled how Android and iOS have become more and more similar in their approaches. The "Android tax," as we've referred to it in the past, no longer exists. Generally, Android and iOS apps can now be built with the same quality, with comparable timelines, and budgets. While that doesn't necessarily mean we suggest building platforms in parallel, it's a huge relief for people creating apps.
Thanks! Yep, the canopy clamps and the grooves in the bed liner are the only things holding the side shelves and sleeping platform in place. You just pop off the clamps with a ratchet and the whole things lifts out / slides out easily. That’s what I did to treat the wood after construction, takes maybe 15 minutes to pop out. Very modular. It’s been in there for more than two years now, same wood, and everything is still looking good and working fine. I like it!
In our opinion, the best kind of fridge you can get for a DIY campervan is a portable 12V fridge/freezer. These fridges are built for adventuring on 4x4 vehicles and boats. They’re very rugged, and they don’t need to be kept perfectly level like mini-fridges. They can run off 12V power or regular 110V. They keep your food as cold as you want, and they can operate as either a fridge or a freezer.
Now this Super Pencil from C.H. Hanson does all of that and more. The entire pencil is made from a non toxic graphite composition so the whole thing is a writing surface with no wood around it to shave away. Super pencil marks are water and smudge resistant and because the composite is so durable it never needs sharpening even when you use it on rough materials like concrete.
A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
There’s a lot of blood, sweat, tears, and cash that goes into starting and running your own small business. One of the primary benefits of incorporating is that it limits the liability and risk of any losses your business may accumulate along the way. In other words, when you incorporate a business, you are typically not personally responsible for business debts. So if life happens and something goes wrong, as long as you and your business are not legally considered the same, your house, your car, and your goldfish are all safe.

Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
At least once a year I want you to set aside some time (I’m talking about a large chunk of time - like a day) and I want you to write down everything you want to accomplish this year or next year (or whenever you are planning for). I tend to plan for a whole year, but you can try 3-6 months to help you get started. Take away any and all distractions because it’s important that you are super focused on what you want to accomplish for the year. This is the time to let your ideas flow, don’t hold back. Things on this list can include: Launch your own website, release a new invitation line, and work on my Instagram account. Don’t overthink, just write down what comes to your mind and whatever your heart desires. There will be time later to refine what you have written down. When you are starting to brainstorm your goals, I would suggest that you first start off writing them on a notepad like this. And then once you are done, you can move them over to a task organizer like this.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.

Now, photographs or video tape will also be very useful especially to pass along to your insurance adjustor. Now the problem is this documentation won’t help you at all if it’s lost or destroyed so consider saving your information electronically. Take your photos with a digital camera and create a list of all your valuables, and save both in a computer file. This file can be saved to a disk you can keep at work or upload it to a website that you can access it from anywhere including your home.
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
One of the core skills needed when starting a small business is the ability to build out a diversified product line that is complementary to the headline product(s). It’s hard to imagine a successful business called “Burgers and Scarves,” right? As a good rule of thumb, a well-thought-out product line allows for the customer to upsell themselves. You want them thinking, “I’m having a burger, y’know what I’m going to have some fries too.”

The level of sophistication in a $250 shop is significantly less than a $2,500 shop.  But keep in mind even a $2,500 budget is entry level.  Acquiring a shop full of the perfect tools for each and every job takes a life time.  But that doesn't mean that producing quality work takes a lifetime.  One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.

Equity financing is money raised in exchange for a share of ownership in your business. The core benefit of this type of funding is the lack of debt. You won’t have to worry about those pesky monthly repayments. The downside? You are giving up total ownership of your business, you are giving up the rights to a portion of the ongoing profits of the business, and you are potentially giving up some control of how your business is run (Though this is not always the case).


Once you know your top priorities, you can start thinking about the space each element can take up and where it should go. It is like putting the pieces of a puzzle together when you're working with a small space, so don't get frustrated if it doesn't work out right away. And know that you'll likely have to make some sacrifices. Play with a few options, and choose the one that works best for your situation.

I am a firm believer in having your business goals align with your personal goals. In order to do that, you need to know what your personal goals are. This may be different for everyone, but I want you to be 100% honest here. I am writing this as an update in 2018 to this original blog post and I want to be honest and share with you my personal goals for 2018:
Google - If you have any question in the world, you can google it and probably find the answer, lol. However, I know your concern is how accurate the information is that you are getting. You also want to make sure that when you find some great knowledge, that it's leading you in the right direction. So if you google "how to make money from my Instagram following" or "how to drive buyers to my Instagram account", then you want to find actually step by step instructions, that will actually lead to a real result. Sometimes that isn't always the case. So search and try to put the pieces of the puzzle together to help you, but just know that it probably won't be handed to you on a silver platter like my webinars are. If you are having problems with your SEO for google, then I recommend that you get my Google SEO Webinar.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Hi, I have looked through pictures of the shop books. What I am interested in finding is a book with layout design options. I am ready to build a new shop for myself and want to put dust and electrical under the slab. Best layout designs would help me to figure out how to layout a shop that is aprox. 28'x 36'. Is there a book that has this type of information.
A great supplier will provide the raw ingredients of your success — often literally. What’s more, they’ll deliver them on time, every time. And they’ll always deliver exactly what you ordered, no more, and no less. A large part of the process of inventory control is ensuring that you are paying for exactly the inventory that comes through your door, and not a penny more. Even great suppliers, however, are looking for the highest price possible for their goods, so once you find them, make sure you’re ready to negotiate!
We love natural light as much as anyone, and the big windows in our van were something we were super excited about. But when you're living in a van, you'll want some privacy. Trust me. You'll also need curtains to keep out the lights when you're trying to sleep. Making your own curtains can seem like a daunting task, but it's not all that hard. (I speak as someone who had to look up a tutorial to operate a sewing machine!)

A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.
Well, my workshop is finally complete and I’m ready to take on just about project that comes down the line. And I’m pretty well set up here. I’ve got a great workbench, plenty of table space over here that easily rolls around the shop if I need it, lot of storage space down here, I can tuck these tools away or bring out any new ones that I need. And as you can see I’ve got plenty of supplies to tackle just about any project.
In our Complete Coffee Shop Startups Kit, we spend a good amount of time discussing your health department requisites, your coffee equipment, and even the design of your coffee shop. Since this makes up a significant bulk of your startup costs (equipment, space requirements, etc.), we recommend that you spend an extra couple of hours strengthening your knowledge base with listening to our audio interviews.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
Up until about ten years ago, if you were in the process of starting a small business and wanted to use all of the technologies listed at the start of this section, you would have needed to take out a second mortgage to cover the bill. Investing in retail technology has historically involved expensive hardware (including an in-house server), large upfront software costs, and hefty ongoing bills for customer support or repairs when things went wrong. Innovators were targeting large-scale enterprises like Coca-Cola, not local mom and pops, so the packages and price points were designed to match.
×