In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly without any major issues.
In a small space, there's not much room for one-trick ponies: You need gear that can do many different things, and that goes for your work space and stands, too. You can add a wood clamp to a multifunction workbench, but you probably need compact work or tool-holding stands to make up for the lack of a large work surface. Occasionally you may need to take your work to another room or even outside, in which case portability is also important.
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
For small business owners, these tools present an incredible opportunity to set smarter business goals and easily identify some of the key factors of success and growth in their business. However, when you couple the breadth of technology options with decisions about basic store and restaurant equipment, such as espresso machines or air conditioning units, it can become a little overwhelming to figure out what is actually worth the investment.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws. Because of this, I'd stick to the two saws we looked at in the $500 build: The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110. These two additions bring our running total to just over $500.
Now I want you to create a spreadsheet or use my worksheets and write one major goal on the top. This can be the first goal you want to accomplish. Then I want you to list all the tasks you need to do (or someone on your team has to do) in order to accomplish this task. For example; let’s go going back to the goal of "Launching a New Website". The tasks you will need to do to get this goal accomplished are the following;
Remember, your retail store layout guides product placement, directs customer flow, and defines the overall look and feel of your store, so it deserves plenty of thought. Many factors will affect your floor plan choice, including the size and shape of your sales floor, the types of products you sell, and even the customers you hope to attract. Keep these factors in mind as we explore each floor plan option in detail.
In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts. Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up. A more economical approach would be to build your jigs as your projects demand them. After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
A lot has changed in recent years. Sophisticated, yet affordable technology now exists that can help track customer relationships from an ad placed on Google, right through to a successful sale. This offers small business owners a unique chance to be entirely data-driven in their marketing approach. Every single aspect of your small business can be tweaked and optimized to ensure that you are enticing customers, up selling where possible, and encouraging people to spread the word about your business.
A great product line will also reflect a range of price points. For a business that is working hard to convey a sophisticated and elite vibe, it might be a useful strategy to set a high minimum price, but for the vast majority of small businesses, your pricing should be guided by one key thought: I want every single person who comes through my door to be able to find something that fits their budget.
At a time when you’re focused on getting in front of customers as quickly and as often as possible, it can be hard to think about official requirements like registering a business name or deciding on a legal structure. Still, now that you have decided to start a small business or buy an existing one, one of the first critical steps is determining the business entity that's right for you.
Shops have value on many different levels. There is the satisfaction of having a place to create and work on projects that is hard to quantify, but definitely improves your quality of life. There is the value to your small business of having space in which to work wood and thereby generate income. There is the dollar value of the build itself, which will be a considerable investment and, finally, there is the resale value of your property after you’ve added your shop. Before you go too far, though, it’s worth asking a local real-estate agent about the potential return on your investment in your area; generally shops won’t add significantly to the value of your property, so it’s worth thinking carefully about what else the space could be used for if you were to sell. The decision about whether it is worth it to build is a matter of balancing all these factors: projected sales balanced against the cost; the cost of building is balanced against what it will be worth when you sell. Woodworking can be a creative outlet, can give you a sense of mastery, and even be a way to give back to your community by donating beautiful pieces to local charities for fundraising auctions, or creating pieces that future generations will inherit. Ultimately, the value of a shop might come down to the emotional and social returns that it will pay you and the people around you for years to come.
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.
The nomadic truck camping lifestyle has been incredibly freeing, not only is cheap and accessible to most anyone, but it can take you beyond places you even imagined. One book that I’d recommend to all newcomers to this lifestyle is Bob Wells’ How to Live in a Car, Van, or RV, which will help you better understand the ins and outs of this lifestyle.
To get the most out of your router, you are going to want a router table. You may find yourself asking if you really need one - if you do, check this post out. It's one of those purchases that you won't truly understand how valuable it is until you have one. Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150). If you want to see our favorite tables along with write-ups, check them out here.
What about when you’re camping? Well, most campgrounds (including many free National Forest and BLM campgrounds) have some sort of bathroom situation. If there’s not an actual running water bathroom, you’ll typically find pit toilets (aka vault toilets), which are basically much nicer/cleaner permanent porta-potties. We also recommend picking up a good poop shovel for those times you’re camping in a wilderness area without bathrooms.
This is where I started thinking about how I was going to store all of my lumber. I had planned on building a wall rack, similar to what I had used in my single car garage. But I hated using up an entire wall for lumber storage. I also knew from experience that I would easily lay stuff against it and soon be digging lumber and junk out of my way. I decided to use the space under my workbench to store the long boards and I realized that by pulling my bench out from the wall I could slide sheet goods behind it. This created a problem: How do I get it out. The Shop isn't long enough to pull out 8 foot boards from inside and I would probably have to move things around to get to it anyway. So my plan for this came at kind of a sudden epiphany moment, when I decided to cut access doors in the front and build my storage into my workbench area. This has been the single best idea that has come out of my shop. I can't express enough how easy it is for me to get straight to a board i need with no hassles. I just remove the doors and pull out what I need. I can store a surprising amount of lumber in this area. I do have a secondary area for some cutoff sheet goods and a scrap bin next to my table saw in the garage. But this area stores most of my lumber.
While we think a battery isolator and a 200-watt solar kit provide more than enough power for most vanlifers, some people may want additional ways to generate electricity and charge up their batteries. Especially if you’re planning on running power-hungry electronics like TVs and air conditioners, adding a generator and/or shore power hookups will help you deal with the extra load.
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts.
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.
The first thing to understand about a business plan and financial projections is that the process of compiling them is often more important than the final product. Sure, the actual sheets of paper, filled with spreadsheets and graphs with pretty arrows pointing up and to the right are great — and can be very important in helping you to secure funding — however, when it comes down to the brass tacks of starting a successful business, it’s the process, not the paper, that counts.
Do you have 3 goals left? Great! That's the perfect number. Do you have more? That's okay as well. If you have more time to work on your business, then you may be able to accomplish more then 3. But it also depends on the type of goal you are trying to accomplish. I just recommend not trying to over achieve in fear of not accomplishing everything you set out to do.
Aside from mechanical repairs, a mechanic’s toolset will help you loosen and tighten bolts - which you’ll need to do during the gutting process, installing your electrical system, and at many other points during your van build. This Crescent 170-piece tool set has all the essentials, including 6-point and 12-point sockets in ¼”, ⅜” and ½” - not to mention pliers, crescent wrenches and screwdrivers.
Once I had the walls completely filled in and trimmed out, I built my doors. I clamped them in place each day until after I painted. Then I installed the hinges and hardware. I decided to change my original plan of building a hinged 4 foot door. I was worried that the weight of it would cause it to sag over time. I had also decided at this point to install a small unused AC in the back wall. I thought that by keeping one of the doors closed, I could keep more cold air in during the hot summers.
A software engineer needs to know how to code. An administrative assistant must answer phones and organize paperwork. But a marketer typically needs to wear many hats, from writer to advertiser to strategist. And unlike other job roles, marketing employees can affect the core of a business by changing the way it’s positioned — and they can be held accountable to the company’s bottom line.
The more outlets the better! I have a good mix of 220v and 110v outlets throughout the shop. I even included a few in the ceiling and the floor in hopes of avoiding power cords in the walkways. And although this contradicts my previous comments about over-committing, I picked locations that would likely work for various tool configurations. If at some point they don’t work for my setup, I just won’t use them.
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.
When starting your small business, the type of business structure you choose will depend on three primary factors: liability, taxation, and record-keeping. Most small business owners begin their commercial life as a sole proprietor because it’s the easiest way to get started. In fact, if you’re in business and you haven’t taken any action to incorporate, you are most likely deemed a sole proprietor by default. You are entitled to all the profits of your business but also responsible for all its debts, losses, and liabilities.
Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.