If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based busi­nesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of run­ning into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibili­ties that your property will allow.

If you’ve got 220v, and want to get a seriously good TS, the Grizzly G1023RL is about the best bang for the buck in a 3hp industrial style cabinet saw…$1195/$1294 shipped. It’s not a necessity to have that much saw, but it’s close in price to many lesser saws, and is about all you’d ever need. If that’s more than you can stomach, and/or don’t have 220v, you’re limited to a TS that’ll run on a standard residential 110v outlet….again I’d look to a full size stationary saw. The typical contenders are the entry level price ranges are the Ridgid R4512, nearly identical Craftsman 21833, Steel City 35990, Porter Cable PCB270TS….all under $600. The next step up would include the Grizzly G0661, G0715P, Craftsman 22116 (by Steel City/Orion), Jet Proshop, General International, Rikon 10-201, and Powermatic offerings. These saws all have the potential to perform well…the end performance is largely dependent on how well you set them up, and what blade you choose.


Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.


Let’s face it, one of the most significant costs of your shop will be its foundation. While you’re at it, what about adding space above your shop? There may be regulations preventing you from building living space above your shop if it is in an urban setting or in an outbuilding, but there may be some flex­ibility depending on where you live. It is in the municipality’s interests to encourage infill housing that uses existing infra­structure. At a minimum, think about including attic trusses to create some space above your shop for drying lumber or storing equipment. Access could be from simple pull-down attic stairs or from the exterior if you don’t want to lose floor space to a stair or ladder. If you’re creating an addition to your house, you may be able to add a couple of rooms you’ve always wanted, such as a family room, office or in-law suite.
According to a recent digital marketing survey conducted by Clutch, 74%of small businesses surveyed had a company website. Of the businesses that said they do not have a website, 9% said they planned to build a website in the future, while 10% said that that they are unlikely to build one. One thing is clear, small business owners are starting to join the digital revolution and are reaping the rewards in terms of increased customer loyalty, growing word-of-mouth, and most importantly, increased sales. 

Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.

Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.

Our practical workshop is coming along nicely. We’ve created a big open space and added plenty of electrical power and lots of light. We’ve also added some great storage capacity using recycled kitchen cabinets and some old shelves. Now, with our tool compartment and work surfaces in place we’re getting very, very close, but I wanted to get a little input on the final details from some other folks who spent a lot of time making sawdust, so I asked my co-host Allen Lyle and our website editor Ben Erickson to look around and give us some of their ideas.
Hey Kasey, I don’t do anything for insulation, I treat truck camping just as I would cold weather tent camping. Just bring a good sleeping bag and learn how to manage in the cold. Usually the side wall of the truck is not at a perfect 90 degree angle, so you will need to check out the angle and compensate. You can hold up a small piece of 2×4 at the back to judge the angle and make a few test cuts to ensure it sits “flat” aka level.

Now this Super Pencil from C.H. Hanson does all of that and more. The entire pencil is made from a non toxic graphite composition so the whole thing is a writing surface with no wood around it to shave away. Super pencil marks are water and smudge resistant and because the composite is so durable it never needs sharpening even when you use it on rough materials like concrete.

I’m picking up a 4×4 Extra cab pick up tomorrow and selling my current 97 Tacoma. It’s older and it’s got a lot of miles but it still has a lot left to go. Mine is available in the 3 grand range. They’re hard to find and all the rust free trucks are out here in the west but mine is one example of many good Tacos that are available at an affordable price that will fit the bill perfectly.

Amenities and Services – You’ll want to understand the full range of amenities offered by a commercial space. These amenities and services may include such things as communal rooms, free Wi-Fi, loading bays and docks, dining options, outdoor space, sewage and utilities, on-site security, and more. The zoning of your business will often dictate the type of amenities and services you require.
A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
I’m a 60 year young widow who just bought a bright yellow 2003 S10 step side with the intention of camping in it. But I discovered that finding a used S10 step side topper is harder than finding hen’s teeth!! Buying a new one wasn’t an option. Just found a black step side topper for a Ford Ranger. Isn’t a perfect fit but it works. And the colors compliment each other although color wasn’t my primary concern. I took two days to drive from the St. Louis area of MO to the Kansas City area to pick it up.
In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly with­out any major issues.

You may already be aware of something known as the "butt-brush effect," coined by consumer behavior expert Paco Underhill. He discovered that a typical customer, especially women, will avoid going after merchandise in an aisle where they could potentially brush another customer's backside or have their backside brushed. This holds true even if the customer is very interested in a given product. An easy way to avoid this problem is to ensure that your aisle, floor, and displays allow customers to have more than adequate personal space when browsing your products.
All this is why I recommend you buy the very best stuff available, even if it means going without certain tools initially. Although it wouldn’t be a disaster to spend $1000 on a whole bunch of inexpensive tools, what are you going to do when you’ve outgrown the capability of these tools and want to upgrade? You’ve now got to somehow get rid of the cheap stuff and replace it with something better. This isn’t easy and it’s always the most expensive way to go.
First, let's dump that hand powered saw/miter box.  It gets the job done, but it takes forever.  We're still on a lean budget, but shelling out ~$110 for a 10 inch electric miter saw makes a lot of sense.  This won't be your forever saw, but it should do fine for most projects.  It can handle up to a 4x6 stock which will cover 99% of what a beginning wood worker will throw at it.  
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
×