These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.

Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.
If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based busi­nesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of run­ning into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibili­ties that your property will allow.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.
There are some variances in the features and reliability of different model years, and differences between the Mercedes Sprinter, Dodge Sprinter, Ford Transit, and Dodge Promaster - so make sure to do your research. The Sprinter RV Conversion Sourcebook is an incredible resource on all things Sprinter (and van conversions in general), and it goes over all the options in detail.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.

Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
Skoolies do have significant drawbacks, however. Their size makes them a bit unwieldy to drive, and getting to some of the more out-of-the-way camping spots just won’t be an option. If something goes wrong mechanically, it can be much more expensive to fix than a normal vehicle. Also, the sheer size of these vehicles means the gas mileage is much worse than other options.
Well, we’ve managed to put together the workshop I’ve always wanted. One that’s practical, functional and neat, well at least for the moment. We have plenty of light, plenty of power, lots of work surfaces and enough cabinets, shelves and hangers to organize all of the tools we’ll be using here. I’ve even managed to do a little creative workshop decorating along the way to remind me of how I got started in this business in the first place.

In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
If this all sounds too complex for you, there are alternatives. Thanks to advances in technology, there are tools available that help simplify bookkeeping and accounting so that you don’t have to hire a full-time accountant to take care of the basics. We’re big believers that a technology-led approach to running a small business will leave you with more actionable insights, more time to focus on your day-to-day operations, and ultimately, more money. For details on the cloud-based technologies that more and more businesses are relying on, make sure to check out our cloud-based business guide.
I like how you thought out the lighting for you shop. I have 6ea.6 tube T-8s but find 6500K bulbs but find lighting for filming is not that good, seems dark to me I use a Canon T3i its a decent camera I do have a row of windows in a 16′ garage door and aman door with a window on one end and a small window at the other end of my shop. Any idea what the issue may be?Could I still be getting too much light?

“Beware suppliers bearing gifts. That ‘free’ refrigerator from the drinks supplier is never really free. You can quickly find yourself tied into sub-optimal deals because of a reliance on this hardware. If you have access to the capital, do yourself a favor: Buy your own fridge and negotiate from a position of strength.” — ShopKeep Founder and Experienced Small Business Owner
Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
Other than that, you can’t have too much light — especially north light! — and you want accommodations for all the electricity you can imagine. Ceiling fans are a must. A good dust collection system is good, too. Don’t forget to plumb in for compressed air. Do NOT use hard PVC water pipe for compressed air — ever. If/when it breaks or ruptures, it explodes into tiny sharp glass-like shards. I know firsthand. I’ll tell you about it some other time. Think balloon popping!
Commercial law exists for one simple reason: money and trust have a long and storied history of mixing like oil and water. Throughout the millennia-long history of commerce, aspiring businessmen and women have been lied to, cheated, scammed, cajoled, bullied, and otherwise disconnected from every single dime they had by unscrupulous suppliers, greedy investors, and dishonest business partners.  

WOW that is a nice size shop! I am looking forward to more videos on the shop projects! We have been shopping for a house for over a year & have finally found one but it has nothing for me to use as my woodshop! I currently have a basement shop that’s 24×40 & it’s really huge for me I couldn’t imagine any bigger. Anyway I will be looking at building a new woodshop for myself (yes I am a female woodworker) & you have given me lots of great ideas so far. I am an Artist & wood is my preference, everything I make is quite small (no furniture or anything that big) but I have lots of specialty tools for what I do as well! Thank you for sharing your ideas & all that you do. Keep up the great work!
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.

A battery isolator allows your vehicle’s alternator to charge your auxiliary batteries while you drive, and keeps everything separated so you don’t drain your starting battery. Since we installed our Keyline Chargers Dual Battery Smart Isolator, our batteries are almost always fully charged. It’s also very simple to install - the toughest part is running the cable inside your van from the engine compartment.
It is also essential to take a lean, data-led approach to choosing a business space. The average length of a commercial lease has dropped over the last few years but is still often well over five years, so the absolute last thing you want to do is rush into a signing and get locked into a bad situation. There are so many ways to test the viability of your business idea before you over-invest and sign a full-blown lease agreement.
Let’s say you’re a Brooklyn-based hipster and you want to follow your lifelong dream of opening your very own artisanal, organic lemonade stand. You’re planning on stationing your retro lemonade stand along a busy road in Williamsburg, Brooklyn. And maybe you want to hire a couple of college kids to collect the money and serve your customers, (probably while wearing some painfully cool 1970s punk band t-shirts). You’re only thinking about it semi-seriously. It might be something you’re going to do when you’re not focusing on your real career as an aspiring DJ.
Does it motivate you? This is a tricky one because sometimes we have to do the work that we don't want to do to become successful. On the other hand, if it doesn't motivate you, you just literally wasted your time writing it down because you wont complete it. Consider your skill set and desire to want to work on that goal to help you eliminate goals (because you can't do everything). 
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
Love the local history of your city or state? Consider becoming a tour guide. Sure, you’ll need to conduct tons of research to be able to do the job well, but that’s half the fun. Set yourself apart by offering tours that speak to a specific niche of your community’s history. Some tour guides offer historical walking tours of their town’s most haunted spots while others curate guided foodie tours for guests to get a true taste of the city.
Are your table saw accessories where you need them—when you need them? Follow reader D. E. Warner’s advice: Attach pegboard panels to the stand to hold the wandering herd of push sticks, blades, throat plates, wrenches and jigs. On an open metal stand with angle-iron legs, drill holes in the legs and bolt the pegboard in place. Here’s another super storage project using pegboard.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  

Ultimate Small Shop offers a comprehensive guide illustrating how to set up a workshop. It may be just a small basement shop or a part of the garage converted into a workshop. The guide lays out all the steps and actually caps the investment at under a thousand dollars. Woodworkers can build their workshop for less than $1,000. This does not entail any compromise of tools or the scope of woodworking projects. The guide provides a shopping list including the best tools and there are exact links to find those tools and buy them at the best prices. There are floor plans to ensure layouts are optimized even in the most cramped spaces.
WOW that is a nice size shop! I am looking forward to more videos on the shop projects! We have been shopping for a house for over a year & have finally found one but it has nothing for me to use as my woodshop! I currently have a basement shop that’s 24×40 & it’s really huge for me I couldn’t imagine any bigger. Anyway I will be looking at building a new woodshop for myself (yes I am a female woodworker) & you have given me lots of great ideas so far. I am an Artist & wood is my preference, everything I make is quite small (no furniture or anything that big) but I have lots of specialty tools for what I do as well! Thank you for sharing your ideas & all that you do. Keep up the great work!
Pegboard panels like this are extremely popular way to display and store hand tools. But they have one annoying problem is that when you lift off a tool, often the hook itself will pop out of the board. And that happens with over a number of times, every time you reach for a tool it can get pretty annoying. So you can buy at the hardware store, they make straps and special devices to hold the hook in place, but I’ve found this works just as well and it’s a lot cheaper.
Whether you end up looking at self-checkout counters, fancy lighting systems, special refrigerated cases, or any of a countless number of options, never forget that these are only tools to help accomplish your main goal. Your store needs to create an environment where customers want to be, where they feel comfortable and appreciated, and where that experience will prompt them to purchase (and hopefully encourage their friends to do the same). Equipment and technology decisions should always be made with your customers in mind.

Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.

We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
Most people know they should document their homes contents for insurance reasons but they often ask why or how to do it the right way. If you have a loss due to fire, theft or a natural disaster your insurance company will need certain details to complete the claims process, including a description of the item, the model number, the serial number the date purchased the color and the purchase price.
Now, photographs or video tape will also be very useful especially to pass along to your insurance adjustor. Now the problem is this documentation won’t help you at all if it’s lost or destroyed so consider saving your information electronically. Take your photos with a digital camera and create a list of all your valuables, and save both in a computer file. This file can be saved to a disk you can keep at work or upload it to a website that you can access it from anywhere including your home.
Simply get a one-inch drywall screw and drive it into the hole right beside the hook. You want to use a one inch screw because you don’t want to hit the wall behind it and you just drive the screw in until the head of it is tight against the hook, it’ll just act as a shim, and you’ll see once I get this all the way in, it lock the hook in place, and now when you take the tool on and off it won’t come off. The hook won’t pop out.
Ryan, I have the same (almost) 90’s Toyota Pickup and love it! this is so helpful, and I will definitely be using this method. my main concern is that 1/2′ plywood sagging. do you notice it sags quite a bit or does it mostly hold up? my thought was to build the vertical bins a little wider, so that the plywood bed platform wouldn’t be under so much stress. the second issue im running into is wrapping my head around trying to organize and compartmentalize things appropriately. what do you typically put where so it is easy to reach and use?

James Hamilton (or “Stumpy Nubs”) is a self-taught tool expert, engineer, writer, teacher and video producer. In 2008 he went into woodworking full time, creating a weekly Internet woodworking show that focused on the workshop itself. Now, Stumpy Nubs Woodworking has grown into one of the most popular multi-media woodworking resources in the industry.


Trying to compete on price is rarely an effective long-term strategy, so it’s important to consider how you will differentiate your offering. Will this be with amazing customer service? Or maybe with superior product quality? Regardless of what you choose, how will you allocate your budget to make it possible? How will you market your small business? How will you get customers through the door?
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
However you design it, a loop floor plan surrounds customers with product displays on outer walls, and allows for all types of creative display variations in the center of the store. A loop floor plan works well for most types of small retail stores, such as apparel and accessories, toy, homewares, kitchenwares, personal care, and specialty products.
While the recession brought with it a well-documented squeeze on small business lending from banks, there are a number of alternative funding sources available to those who are starting or expanding their small business. Loans and/or equity investments can be sourced from multiple sources, including credit unions, savings and loans, and private financial companies. Family members, friends, and colleagues are also potential avenues to explore.
Without organization, living in a van can feel cluttered and chaotic, so you'll want to make the most of your storage space. This is a good time to make sure you've paired down your belongings to a reasonable amount and to make sure everything has a place. (As a former engineer who loves making things as efficient and optimized as possible, this was Ben's favorite step!) 
I’m picking up a 4×4 Extra cab pick up tomorrow and selling my current 97 Tacoma. It’s older and it’s got a lot of miles but it still has a lot left to go. Mine is available in the 3 grand range. They’re hard to find and all the rust free trucks are out here in the west but mine is one example of many good Tacos that are available at an affordable price that will fit the bill perfectly.

Sprinter vans have been around for awhile, but they’re still the new kid on the block. These vans are especially known for their interior height, long wheelbase, and boxier shape - making them ideal for building out a spacious, functional living space. This category includes the original Mercedes/Dodge Sprinters, as well as Ford Transits and Dodge Promasters (check out this article and this helpful graphic for more information on the differences between these).

​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.
Will this make me money? If it will not, cross it out. If you want to keep it on, please rephrase your goal so the outcome can be money driven. For example: Grow Instagram following (bad) vs. use Instagram to drive traffic and sales to website (winner!). This way, you can break that goal down into tasks ( ill show you that in an another step) and those tasks will lead to you actually making money with that goal instead of with just a larger Instagram following.
You know I can remember my very first workshop, and the very first power tool I ever bought when I was nine years old. Well, I have still have it, doesn’t work anymore but it lasted for 20 years, and I bought it from a mail order catalog for $11.41. I’ve held onto it all these years, because I knew I would find some special place sooner or later that it needs to rest. Well here’s a nice spot right here, I think that’s where it’ll end up.

Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.

The enormous range and affordability of options has provided the chance for small business owners to apply technology to their accounting, marketing, and day-to-day operations. You can spend less money, save valuable time, and gather data about almost every aspect of your business. What’s more, you can enhance the way your customers experience your store in a meaningful and cost-effective way.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie

I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
Impulse items like small toys, candy bars, lip gloss, and breath mints are great products to feature near your register. When customers approach the register to pay and leave, you don’t want them to stop shopping. Placing low-cost impulse buy items near registers, as shown in the image below, encourages shoppers to add an item or two as they check out.
Remember, your retail store layout guides product placement, directs customer flow, and defines the overall look and feel of your store, so it deserves plenty of thought. Many factors will affect your floor plan choice, including the size and shape of your sales floor, the types of products you sell, and even the customers you hope to attract. Keep these factors in mind as we explore each floor plan option in detail.
It's a well-known fact in the retail community that in North America, 90% of consumers turn right unconsciously upon entering a store. The first wall they see is often referred to as a "power wall," which acts as a high-impact first impression vehicle for your merchandise. So, be sure to give it extra special attention in terms of what you choose to display and how you display it.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.

The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.


To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.

This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 
Note: Some of the links to products that we recommend on this page are affiliate links. This means that if you click through one of our links and buy something, we get a small commission at no cost to you. This helps us keep this blog going so we can continue to provide you with van build tips, tricks, and guides. We believe in honest opinions, and we never recommend anything we don't know about. Every recommended product on this page we've either used personally, have personal experience with, or have researched heavily.
×