Check your local papers, especially the free shoppers, for information about upcoming shows Another venue for craft retailing is at the local flea markets that spring up in every community just about every weekend. Again the entrance cost is usually minimal. Ultimate Small Shop Result The only other thing you need is a little marketing savvy. With little cost and some effort, you will be well on your way to knowing whether there is a market for your craft. Once you know that, you can move on and think about other ways of selling, such as in galleries, on consignment, on eBay or from your own website. Once you spend your precious time and energy creating a scrapbook, make sure it lasts! There are a few simple things you can easily do to ensure that your scrapbooks look just as good as the day you finished them, for years to come. The first thing to avoid is paper that is not lignin-free. You’ve probably heard that before, and it is true, but what is lignin anyways? Lignin is a stiff component of a plant that quite literally holds it together. Although lignin is necessary for plants and trees, you want nothing to do with it! After a while, lignin will cause photos, fabrics and other paper that touch it to turn brown. Yes, the lignin-free paper does cost more, but it is a vital part of preserving your cherished scrapbooks. If the paper is not lignin-free, it will eventually discolor your photos and other materials touching it. So when buying paper for your scrapbooking projects, be sure to look for packages that say “lignin-free,” because if it doesn’t say it, then it most likely isn’t.The fabric is a big concern for preserving your scrapbooks, but unfortunately, it is often overlooked. Many people assume that all fabrics are acid-free, but they aren’t. Silk actually goes through an acid bath during the manufacturing process, as well as many tie-dyed fabrics. This isn’t to discourage you from using it, not all. Just try to make sure that no photos directly touch fabric, and if you need them to overlap, make sure there is a layer of paper between the two. Another consideration when using fabrics is if the color will bleed off onto your page and other things touching it. To test for this, cut a square inch off and soak it in a glass of water overnight. If there is no color bleeding from it the next day, then there isn’t any risk to your scrapbook. But if you do see color in the water, or collecting at the bottom of the glass then don’t use that fabric in your scrapbook at all. When using glitter, be sure there is a top layer of spray adhesive to lock them down, or better yet use special glitter glue where the glitter is mixed right in. If this is not done right the glitter will slowly fall off, and loose glitter means scratched photos. After you have planned the layout for your photos, be sure that you are using the right kind of mounting tape for them! Regular mounting tape is fine for buttons and bottle caps, but when it comes to mounting photos you need to use special photo mounting tape which is completely acid-free. Ultimate Small Shop Member If you don’t, your photos will slowly discolor. The tape should say “acid-free” right on the packaging.
Power walls are your go-to spot for hot finds, new items, and seasonal features that attract instant attention and pull customers through the entry area and into your store. These areas are likely going to change frequently and you need to plan for it. Outfit these spaces with versatile displays that can be easily changed to showcase various product groupings.
“Beware suppliers bearing gifts. That ‘free’ refrigerator from the drinks supplier is never really free. You can quickly find yourself tied into sub-optimal deals because of a reliance on this hardware. If you have access to the capital, do yourself a favor: Buy your own fridge and negotiate from a position of strength.” — ShopKeep Founder and Experienced Small Business Owner
To get the most out of your router, you are going to want a router table. You may find yourself asking if you really need one - if you do, check this post out. It's one of those purchases that you won't truly understand how valuable it is until you have one. Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150). If you want to see our favorite tables along with write-ups, check them out here.
Really enjoyed watching the video of the shop build. You will be turning out great pieces in no time. At the end of the video it looks like you have your dust collection system up and running. Where did you purchase the duct work? I thought I remember you talking about this in the old shop. Did you use regular HVAC 4″ round duct or a heavier piece. Thanks for the insight and good woodworking.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percentage of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both differ depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
Once I had the walls completely filled in and trimmed out, I built my doors. I clamped them in place each day until after I painted. Then I installed the hinges and hardware. I decided to change my original plan of building a hinged 4 foot door. I was worried that the weight of it would cause it to sag over time. I had also decided at this point to install a small unused AC in the back wall. I thought that by keeping one of the doors closed, I could keep more cold air in during the hot summers.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
Many retail fixture and display companies provide store planning and design services to their customers. Though typically not free, these in-house design services can be far less expensive than hiring an independent designer. Plus, they can help streamline the process of store layout and planning, along with the purchasing and installation of displays and fixtures.
Having a deliberate store layout is important for maximizing revenue for brick-and-mortar retailers. By setting a plan, retailers can strategically direct shoppers to high-priority products and drive impulse sales. An effective store layout also makes the space organized and easy to navigate, which is important for providing a good customer experience.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
So what does all this boil down to? I favour starting with a good workbench and top quality hand tools – chisels, a couple of planes, a hammer, a few Japanese handsaws – stuff like that. You’ll be amazed at what you can accomplish when properly equipped. Build simple items at first, and then add the very best power tools you can – as you can afford to – in the order that makes the most sense for the work you’re interested in. Yes, this gets you off to a slower start, but what’s the rush? You’ll soon surpass the ‘buy-it-all-at-once’ folks who end up struggling with beginner tools that hold them back from getting better.
There are a number of woodworking fixtures you can get by without for a long while, but a sturdy workbench isn't one of them. The trouble is, those solid-hardwood benches we all lust after can completely blow a modest woodworking budget. Here's a bench that splits the difference. You'll get a top that can stand up to significant abuse, a sturdy, heavy base that keeps the bench planted where you put it, and an end vise and T-track system for holding workpieces as well as a variety of unique jigs. It may not look quite like a European bench, but it works just as hard as one for a lot less money.
It’s hard to overstate the importance of choosing the right location when starting your small business. We’re sure you’ve heard the saying 1,000 times before, Location, Location, Location! Some of the world’s most well-financed franchises have this weaved into their business DNA. McDonald’s Ray Kroc is the perfect example. When asked about the business, this well-know American businessman and philanthropist once stated, “We are in the real estate business, not the hamburger business.”
So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.
This OXO palm brush really helps us conserve water while washing our dishes. We fill the reservoir with water and a few drops of Campsuds, and we only squeeze out what we need - so it takes care of both the initial rinse and getting our dishes soapy with minimal water usage. It’s also very compact, and the comfortable shape makes it easy to scrub dishes.