Every woodworker (I think!) dreams of someday being able to construct their own dedicated woodworking space. To date, I have bounced around from garage to garage (about 4 times), making the best of a crappy real estate situation. And while I have been lucky to have fairly large spaces to work in, I still daydreamed about the possibility of designing a shop from the ground up, with both woodworking and video production in mind.

The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.
Table mounted routers, planers and shapers are another machine that usually has material fed through, and although they are fairly narrow machines, they require room on their front for material to be fed from, and at the rear for the material to be removed after the work is complete, so again, a space of about ten feet is needed for any significant work.
Note: Some of the links to products that we recommend on this page are affiliate links. This means that if you click through one of our links and buy something, we get a small commission at no cost to you. This helps us keep this blog going so we can continue to provide you with van build tips, tricks, and guides. We believe in honest opinions, and we never recommend anything we don't know about. Every recommended product on this page we've either used personally, have personal experience with, or have researched heavily.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
“Your sales floor is a living, breathing entity that needs to change—frequently—in order to flourish. It’s the retailer’s job to make that happen. If your store is filled with the latest and greatest products, but your sales are in a rut, it could be because your customers are bored. They come to your store not just to buy; they come for ideas and inspiration. And they come to be entertained—even when they don’t buy anything, that experience is what brings them back.”
At the very least get the basics of shop design right with great lighting, clean displays, and a well thought out layout. Once you have all of this pulled together you can add a dose of your own personality to the store's design to break through the noise and establish a connection with your target customers. The goal is to be memorable and maximize sales per square foot at the same time!
The key to success here is having clear processes written down, promoting from within whenever possible, and remaining open to change. You’ll want to balance your desire to educate your manager on how to manage your business with an openness to feedback and new ways of doing things. You’ll also want to take advantage of the technology available to keep you abreast of things like real-time sales data for all your locations, no matter where you are.
If you’re starting a small business for the first time, your new best friends in life should be your bookkeeper and your accountant. The former should be engaged for a few hours every week (especially at the start of your business) to compile your books and ensure your records are maintained to the required standard, while the latter will help review your tax situation and prepare financial statements. Both can also be used as invaluable sources of actionable intelligence about ways to reduce costs, increase margins, and generally streamline your finances.You’ll be able to spend all that time you save doing what you love and thinking strategically about your business.
The final size I decided on was 1800 sq. ft. Yeah, that’s big! I actually balked and second guessed myself after we received the estimate from the contractor. Sure, more space is nice, but at what cost? I then asked for a second estimate, bringing the shop down to 1500 sq feet, which is still huge. As you might expect, the savings just weren’t that substantial. By the time you get over 1000 sq. ft., the price per sq. ft. is really low, making it very difficult to justify down-sizing. So I bit the bullet and stayed with my original choice of 1800 sq. ft.
Well, all these years we’ve always planned on this being a nice little workshop, and now’s the time that we’re about to remove all of this and create a nice realistic, practical workshop. Not a TV workshop that just looks good, but one that will be perfect for us to use for some of the projects we have on the show, and again it will be used by our construction company for some of the projects they have.
I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
Large or small, most retail stores use one of three basic types of retail store layouts. Which type you use depends on the kind of store you have and the products you sell. For example, grocery stores usually use grid layouts because they are predictable and efficient to navigate. Boutiques typically use more creative layouts that allow businesses to highlight different products.
Garage spaces are usually not insulated, and garage doors on most homes have very poor insulation. That means it’ll inevitably be super hot and stuffy in the summer, and freezing cold in the winter. To be comfortable in your workshop you’ll need to take the extra step to insulate your garage and set up some space heaters, and some portable floor or window AC units. Having to wear a heavy coat while you work will impede your DIY efforts and nobody likes working in a sauna.
It’s no accident that some of the best marketers in the tech startup industry are known as “growth hackers.” Think about your target demographic (e.g. students, local mothers, teenagers) and find any way you can to get the word out to them. Email mommy bloggers, hand out free samples at the local college, or write your website on all the napkins you hand out with your food. There is no substitute for action.
One example is testing your products and services for their desirability through ecommerce. It might turn out that your core product line will actually be much smaller than you originally envisioned. Equally, there are now a number of services (such as storefront.com) that will allow you to secure a pop-up lease in some incredible spaces, often for only days at a time. It might just turn out that your dream location isn’t as great as you originally thought.
2) I haven’t spent very many nights in full on winter conditions (that 12 degree night in Boise comes to mind!), so I can’t comment too much. It was fine for that… Mostly it was hard transitioning from the warmth of the cab to the frigid air while you are shifting things around and getting ready for bed, but then once you were inside the canopy it was fine. Lots of frosty ice on the inside windows, but in my sleeping bag all was well. It stays a little warmer in the canopy. Maybe I’m a wuss, but I didn’t want to spend an extended period of time dirtbagging it in my truck while I was ice climbing (I spent the first two months in Ouray, CO, sharing a rental), I just thought it would be too challenging/miserable to dry and manage gear in a confined space with the shorter daylight hours. I’d be perfectly content doing future weekend trips with this setup though!
Ryan, I have the same (almost) 90’s Toyota Pickup and love it! this is so helpful, and I will definitely be using this method. my main concern is that 1/2′ plywood sagging. do you notice it sags quite a bit or does it mostly hold up? my thought was to build the vertical bins a little wider, so that the plywood bed platform wouldn’t be under so much stress. the second issue im running into is wrapping my head around trying to organize and compartmentalize things appropriately. what do you typically put where so it is easy to reach and use?
After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to pur­chase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very rea­sonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do any­thing I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching. 
There are certain areas that are the responsibility of the federal government, such as firearms, fish, and wildlife. For more on these federal requirements, enforced by bodies such as the Food and Drug Administration (FDA) and the Environmental Protection Agency (EPA), you can explore the information here on the Small Business Administration (SBA) website.
Keep in mind that if you filed to become a corporation or LLC, then you can skip this step altogether. When you form an LLC or corporation for your business, your business name is automatically registered with the state. However, as mentioned before, if you legally registered your name as Bob’s Bike Shop and would like to conduct business using any variation of that name such as BobsBikeShop.com or Bob’s Bikes, you will need a DBA.

Pegboard panels like this are extremely popular way to display and store hand tools. But they have one annoying problem is that when you lift off a tool, often the hook itself will pop out of the board. And that happens with over a number of times, every time you reach for a tool it can get pretty annoying. So you can buy at the hardware store, they make straps and special devices to hold the hook in place, but I’ve found this works just as well and it’s a lot cheaper.

Lease build-out credits – These credits represent the ability for a tenant to make leasehold improvements in their commercial space at the expense of the landlord. These expansions and improvements are necessary for the successful operation of the business. With build-out credits, landlords either offer a reduced rent, reimburse the tenants, or pay directly out of pocket.


In our opinion, having one of these is an absolute must for living on the road - especially in humid areas. To fully cover the width of a van’s side doors/back doors, you’ll need a larger screen that’s designed for French doors. If your vehicle has a smaller door opening like an RV, a screen meant for a standard door will work fine. We could only find standard door screens, so we bought two and hot-glued them together to cover up our side door.
When we started putting together our water system we decided to look for a stainless steel tank. Even though plastic tank options are FDA-approved for potable water use, we still don’t like the idea of our drinking water being in contact with plastic for extended periods. Sure, they say it’s “safe,” but not long ago water bottles containing BPA were considered to be safe.
For example, on your dual battery, the farm just purchased a brand new 2013 Chevy 3500HD with a dump bed. It has dual batteries. How was it installed? They grounded both batteries to the frame and connected the positives with a very large fuse. ~15k later its still working. While its not recommended to do it this way, I think it would work fine in your case. Add the marine battery somewhere in your shell and run a heavy positive from the original battery. Put a large fuse in it(I’d research to see the number, I can’t remember off the top of my head) and your isolator switch inline (probably 2nd battery side of the fuse).
In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly with­out any major issues.
So before you start to consider fixtures and displays, think about the product positioning throughout your store. Where are your evergreen, seasonal, limited availability, and sale products going to be featured on an ongoing basis? This process is called product mapping. Following is an example of a product mapping plan that features a mix of product categories in defined areas:
Finding reliable cellular service (and the internet that comes with it) is a constant challenge in vanlife, especially if you do computer-based work on the road. A cell signal booster like the WeBoost Drive 4G-X helps a lot in areas where service is spotty. It can take a weak cellular signal and amplify it into usable internet for web browsing and getting work done.
It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
Our practical workshop is coming along nicely. We’ve created a big open space and added plenty of electrical power and lots of light. We’ve also added some great storage capacity using recycled kitchen cabinets and some old shelves. Now, with our tool compartment and work surfaces in place we’re getting very, very close, but I wanted to get a little input on the final details from some other folks who spent a lot of time making sawdust, so I asked my co-host Allen Lyle and our website editor Ben Erickson to look around and give us some of their ideas.

Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back.
I’m a 60 year young widow who just bought a bright yellow 2003 S10 step side with the intention of camping in it. But I discovered that finding a used S10 step side topper is harder than finding hen’s teeth!! Buying a new one wasn’t an option. Just found a black step side topper for a Ford Ranger. Isn’t a perfect fit but it works. And the colors compliment each other although color wasn’t my primary concern. I took two days to drive from the St. Louis area of MO to the Kansas City area to pick it up.

In an indoor or basement shop with industrial carpeting, lay down inexpensive laminate flooring to make your life a bit easier at the end of the day. Be sure to anchor the panels or place a large rubber mat beneath to keep them from sliding over the carpet. (Covering up your carpet is even more critical if you want to go beyond wood and work with a material such as aluminum in your indoor shop; metal shavings dig into any kind of carpeting and are incredibly frustrating to clean up.)

Gutting: We actually took on a pretty big project when we bought our van because it came with a preinstalled wheelchair lift that we had to remove. Unbolting all the parts took both of us working on it for a full day, and it wasn't the most glamorous job. The good part was that we were able to sell the lift and the reclining bench seat for a combined total of $260. If there's anything to remove from your van, do this first.
There seems to be two things I like looking at and they are work benches & work shops. I too use my work shop for several other activities. I currently have a basement shop with a walk out entry, which is roughly 340 square feet and shaped like a flat s and has less than 8' ceiling height. In that shop I have an old Unisaw w/50"fence, 8" jointer, 15" planer, 10" sliding compound saw, 14" bandsaw and various & assorted power & hand tools. Also in the same space I have a small closet, dog grooming tub, & a space where a bathroom was roughed out. It is far from finished space and I have plans to put up a ship lapped paneled walls and fix up the closet for tool storage. I also plan on putting a cyclone in the bathroom space along with a tolet. I can work in the space as it is pretty well but the studded walls, insulation, & dust make the space somewhat uninviting. 

Now nobody reasonably expects you to actually hit that exact number in five years time, but the point here is accountability. A really great small business plan forces you to think through your goals, associate a dollar value with each, and articulate clearly how you will make them a reality. By declaring your projected revenue in month seven or your expenses in year five, you are giving yourself a benchmark for success.
Hey Melody, thanks for the email. I’ve traveled through some extremely humid areas (Central America)… I’m taking it that your canopy does not have a headliner? That in and of itself helps a great deal. Personally I would be hesitant to put holes or van roof vents in my cap, but that may be what you want to do. I would try sleeping with a portable personal fan first and see how that helps with the condensation issue. For me it worked wonders while sleeping in those hot and humid environments. I ran mine off the inverter connected to my secondary battery.
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie
Hi thanks for the info. I’ve got a 2009 tacoma and went with a simple, no screws elevated system. I’ve also got a mx series ARE shell with rack rails so I’ll probably take too much stuff now. Oh well. My question is: how did you attach the plywood to the life gate? My carpentry/construction skills are best illustrated by the “Homer Simpson spice rack”. You used the existing holes in the tail gate, but did you put the tail gate cover back on the tail gate and put the plywood over it and screw thru both or ditch the cover? Thanks
A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
The Best Prices for Tools – Ralph shows you where to get the beast deals for the tools and equipment you need. You could buy them yourself from popular outlets like Home Depot, Lowe’s, and Amazon, but the Ultimate Small Shop guide shows you where to get these tools and equipment at cheaper prices. Of course, cheaper isn’t always better. These aren’t just cheap tools that are ineffective. Just good value for money on good tools.
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.
He’s also providing power to a cool light grid we’re building from several old fluorescent fixtures that we salvaged from past remodeling jobs. With six four-tube fixtures, we should get plenty of light. In a work space you want to install these lights high enough so they don’t get in your way when you’re moving materials but low enough to provide good even light.
I was really excited after seeing your shop video. It was almost like you read my mind (except my plans does have more windows and a wood burning stove as I live in TN). I realized the importance of more 22o plugins after you explained your reasoning. I was just planning a couple. Love the floor and ceiling plugins. One quick question. Is each plugin area on it own breaker, or do you have more then one on each breaker. I was planing on each one to have its own breaker. Love your approach on your projects and how you introduce new items or products. Thanks and Merry Christmas
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.

The primary investment of any garage workshop are the tools. Protect your investment with a high quality tool chest that is neatly organized and (if needed) lockable. Look for smooth rolling ball-bearing drawers, and if you’re buying used, beware of rust and dirt that could corrode your tools. We recommend installing drawer mats to keep your tools from sliding around. They also give your tools a softer cushion to rest in.
Although the market has even more options to build apps now than in 2015, there's also clearly more of a distinction in quality. The best app firms and app developers have further honed and distinguished themselves. They have more awards, stronger portfolios, better team members, and more specialized skills. The tools available have made it easier to build apps though, so there's also many more mediocre or low-quality options to build your app.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.
Let’s say you’re a Brooklyn-based hipster and you want to follow your lifelong dream of opening your very own artisanal, organic lemonade stand. You’re planning on stationing your retro lemonade stand along a busy road in Williamsburg, Brooklyn. And maybe you want to hire a couple of college kids to collect the money and serve your customers, (probably while wearing some painfully cool 1970s punk band t-shirts). You’re only thinking about it semi-seriously. It might be something you’re going to do when you’re not focusing on your real career as an aspiring DJ.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
Ultimate Small Shop goes beyond the ambit of Amazon, Home Depot and Lowe’s to help woodworkers start their workshop for less than $1,000. Woodworkers will find answers to questions related to the budget, planning, required tools, critical setup factors and more. The guide has been put together by Ralph Chapman, a coach with more than twenty five years of experience in woodworking. Chapman is the small shop expert and what he recommends is not speculation or best case scenarios. He has done it himself. He is now sharing his experience along with expert recommendations so you can begin your woodworking journey right at your home.

Now I want you to create a spreadsheet or use my worksheets and write one major goal on the top. This can be the first goal you want to accomplish. Then I want you to list all the tasks you need to do (or someone on your team has to do) in order to accomplish this task. For example; let’s go going back to the goal of "Launching a New Website". The tasks you will need to do to get this goal accomplished are the following;
Gutting: We actually took on a pretty big project when we bought our van because it came with a preinstalled wheelchair lift that we had to remove. Unbolting all the parts took both of us working on it for a full day, and it wasn't the most glamorous job. The good part was that we were able to sell the lift and the reclining bench seat for a combined total of $260. If there's anything to remove from your van, do this first.
Amenities and Services – You’ll want to understand the full range of amenities offered by a commercial space. These amenities and services may include such things as communal rooms, free Wi-Fi, loading bays and docks, dining options, outdoor space, sewage and utilities, on-site security, and more. The zoning of your business will often dictate the type of amenities and services you require.
In order to ensure that the staff you’re bringing on board is the right fit for your small business, there’s a few questions that you should ask yourself during the interview process. Are they competent? Capable? Compatible and committed to your core business values? Do they fit in with the culture you are trying to build? And can you offer them fair compensation? Business expert and entrepreneur Alan E. Hall, calls this the 7 C’s to hiring. At the end of the day you want to look beyond the skills and experience they have on paper and make sure that they are willing and able to grow with your business.
Another example of data-driven decision making is scouting the local competition and taking notes on how much traffic they are getting regularly, the kind of products that they’re selling, their pricing, and even how they market their business. This kind of information will help you determine the pros and cons of choosing a location in that area as well as potential strengths, weaknesses, and opportunities that can improve your business plan. Trust us, doing all of this before starting your small business will save you major headaches in the long run.
The Best Prices for Tools – Ralph shows you where to get the beast deals for the tools and equipment you need. You could buy them yourself from popular outlets like Home Depot, Lowe’s, and Amazon, but the Ultimate Small Shop guide shows you where to get these tools and equipment at cheaper prices. Of course, cheaper isn’t always better. These aren’t just cheap tools that are ineffective. Just good value for money on good tools.

The right first step online for most stores and restaurants is creating a Google Local Business Listing. Google accounts for 90% of all global organic search traffic and more and more of that traffic is coming from mobile devices. Chances are, your customers are using Google to find you, so you’ll want to make sure your hours, description, contact details, address, and images are all accurate.
Using six pipe cleaners, you can make your own skeleton. Bend one pipe cleaner into two for the backbone. Twist another around the bottom of the backbone to make into the legs. Do the same for the arms. Join two pipe cleaners and twist them around the backbone leaving some space forming a ribcage. Ultimate Small Shop Woodworking Twist the last pipe cleaner for a head and glue on some eyes. Hang with a rubber band for a bouncing effect. Your kids will love making Halloween crafts with pipe cleaners. But be careful when cutting and keep them out of their mouth. Going trick or treating? Why not make a special jug to collect candies? Cut off the top two inches of a gallon milk jug. Soak to remove any labels. Paint orange. Once dry, paint or stick on eyes nose and mouth resembling a Jack O’Lantern. Use fluorescent paint for a nice effect. The jug can be kept for future reuse. Using glue and food coloring, you can make a see-through painting. Paint a Halloween image onto a piece of plastic wrap. Before the mixture dries, put another piece of plastic wrap on. Cut it out and hang it in front of a light source for a see-through effect. You could also frame the plastic pictures using wood or cardboard if you want them to be longer lasting. Make some hand printed spiders. Ralph Chapman Ultimate Small Shop Apply black paint to your palm and 4 fingers leaving out the thumb. Place palm onto a piece of paper. Turn the paper 180 degrees and print again making sure the palm overlaps. Add some wiggly eyes using either paint or sticks. This is suitable for even 2 or 3-year-olds. Make your own blood. It is less expensive than buying ready-made blood from the Halloween shops. It’s not difficult; all you need is Karo syrup and food coloring. While you’re at it, why not make some slime using glue, water, and borax powder. This is an advanced Halloween craft, so take your time and be careful. Using apples, you can make dried, shrunken heads. Peel the apples and coat with a mixture of lemon juice and salt to prevent browning. Carve out a face of eyes, nose, and mouth. Do not worry about the finer details as they will probably be lost when the apple dries. You can use whole cloves for the eyes and rice grains for the teeth. Let the apples sit out in a warm place for about 2 weeks. If you don’t have 2 weeks, you can speed up the drying by putting them into an oven on the lowest temperature for about 45 minutes and then dry out naturally for the next 2 days or so. Ultimate Small Garage Clock Shop Once dried, they shrink and deform into weird and scary looking faces. Says Angie Maroevich, “You don’t have to spend a fortune on commercial Halloween supplies to have a great party.
The key to success here is having clear processes written down, promoting from within whenever possible, and remaining open to change. You’ll want to balance your desire to educate your manager on how to manage your business with an openness to feedback and new ways of doing things. You’ll also want to take advantage of the technology available to keep you abreast of things like real-time sales data for all your locations, no matter where you are.
You’ll also want to evaluate your obligation to your employees’ health care provisions following the introduction of the Affordable Care Act, which mandates the responsibility for the cost of insuring full-time employees to businesses with 50 or more full-time, or full-time equivalent employees. It also provides generous tax credits to smaller businesses with 25 or less full-time equivalent employees. Need a little more help understanding how U.S. health insurance reform affects your business? Register for one of the SBA’s upcoming Affordable Care Act webinars. They also offer recordings of previous webinars in both English and Spanish for those who can’t make it to one of their live sessions.
I totaly get not wanting to get into the cost part of the shop. We just went through a house renovation, and my stock answer to the ‘how much’ question is either ‘enough’, or ‘enough that was right for us’. There is a quality of life or utility aspect that every person needs to figure out for themselves. And, I would think not having to bounce around from garage to garage anymore has gotta be worth something!

Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.

If you have some experience under your belt, put it to good use as a life or career coach. Many of us are looking for guidance in our careers -- and finding someone with the time to mentor us can be tough. Life/career coaches don’t come cheap, but they are able to offer clients the intense and hands-on training and advice they need to make serious moves in their personal and professional lives. After all, sometimes everyone just needs some uplifting advice.

Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
Starting to see a trend here? Notice how each of these questions begins with the customer in mind. As with all things related to your store, it’s critical to put your customer at the core of your decision making. At first glance, little things like cold drinks that aren’t quite cold enough, can seem insignificant, but it’s often the little things that hurt the customer experience and can turn a customer off to your business forever.
Even if a website and social media aren’t part of your immediate plans for launching a business, as a savvy 21st century entrepreneur, you want to make sure that you have complete ownership of your brand identity before paying any fees required to register your business. Using the example of The Sunny Rabbit, at the very least, you would want to run an online search to ensure that TheSunnyRabbit.com is available. Assuming you want to join the other 50 million small businesses marketing to customers on Facebook, you’ll also want to make sure that Facebook.com/TheSunnyRabbit is also available.
Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for bill­ing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.

If you have some experience under your belt, put it to good use as a life or career coach. Many of us are looking for guidance in our careers -- and finding someone with the time to mentor us can be tough. Life/career coaches don’t come cheap, but they are able to offer clients the intense and hands-on training and advice they need to make serious moves in their personal and professional lives. After all, sometimes everyone just needs some uplifting advice.

Shops can range from functional spaces adorned with unpainted wallboard to beautifully finished, painted, and trimmed-out spaces. Ultimately, I think it depends on your budget and how important your surroundings are to your mindset as you’re working, or to your clients’ if they will be viewing your shop. If finishing your shop will improve the quality of the work that you will produce, thereby relaxing or inspiring you, or showcase for your clients the quality of the work of which you are capable, it may be a worthwhile invest­ment. A more finished space may also allow for activities like parties or even a weekly poker game (as long as drinks stay off the tools).
Hey thanks for the great insight on a pickup camping setup! I just purchased a 2002 tundra with a 74″ bed. Picking it up in Denver in a week and driving it to Durango and then around the southwest. I mainly decided on a truck for a mobile place to keep my dog(that doesn’t have an interior he can rip to shreds), but I am thinking of building a setup similar to yours. You haven’t used yours with a canine companion have you? Any suggestions on keeping it dog-friendly, dog-comfortable and dog-proof? I will be keeping him in the back while at work and such and will be camping in the back with him and possibly another person.
×