I spent a full week grading, compacting the soil and leveling each block before laying the floor joist.  The last thing you want is to finish your new workshop and have a corner start sinking into the ground.  My floor inside my shop is perfectly level still with a 6 foot level.  You can see that I had a drop of about 12 inches on the low side.  During heavy rainstorms, water can flow like a stream next to the fence.  I wanted to make sure my workshop was high enough off the ground to avoid any flooding issues.


So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to pur­chase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very rea­sonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do any­thing I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching. 

Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
“Every time I’m choosing a new a location, I head down there with a big flask of coffee and a clicker to count all the people that walk past. Then I walk to the nearest public transportation at rush hour and look at how people are heading home. I turned down one location because while it was right next to the subway, I noticed all the commuters were coming out of the other subway entrance. It turns out all the residences in that area were on the other side of the street.” —ShopKeep Founder and Experienced Small Business Owner
Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.

I decided to do Optimus for many reasons. One big one was that no one else in the world had done it. There are tons of Bumblebee Camaros and other replica cars, but no other fan of Transformers has replicated the T4 (fourth Transformers movie) and T5 (fifth Transformers movie) Optimus trucks. So if I am to show my son through action what it means not to be afraid to take a chance, I figured Optimus was the best way to try.
Check your local papers, especially the free shoppers, for information about upcoming shows Another venue for craft retailing is at the local flea markets that spring up in every community just about every weekend. Again the entrance cost is usually minimal. Ultimate Small Shop Result The only other thing you need is a little marketing savvy. With little cost and some effort, you will be well on your way to knowing whether there is a market for your craft. Once you know that, you can move on and think about other ways of selling, such as in galleries, on consignment, on eBay or from your own website. Once you spend your precious time and energy creating a scrapbook, make sure it lasts! There are a few simple things you can easily do to ensure that your scrapbooks look just as good as the day you finished them, for years to come. The first thing to avoid is paper that is not lignin-free. You’ve probably heard that before, and it is true, but what is lignin anyways? Lignin is a stiff component of a plant that quite literally holds it together. Although lignin is necessary for plants and trees, you want nothing to do with it! After a while, lignin will cause photos, fabrics and other paper that touch it to turn brown. Yes, the lignin-free paper does cost more, but it is a vital part of preserving your cherished scrapbooks. If the paper is not lignin-free, it will eventually discolor your photos and other materials touching it. So when buying paper for your scrapbooking projects, be sure to look for packages that say “lignin-free,” because if it doesn’t say it, then it most likely isn’t.The fabric is a big concern for preserving your scrapbooks, but unfortunately, it is often overlooked. Many people assume that all fabrics are acid-free, but they aren’t. Silk actually goes through an acid bath during the manufacturing process, as well as many tie-dyed fabrics. This isn’t to discourage you from using it, not all. Just try to make sure that no photos directly touch fabric, and if you need them to overlap, make sure there is a layer of paper between the two. Another consideration when using fabrics is if the color will bleed off onto your page and other things touching it. To test for this, cut a square inch off and soak it in a glass of water overnight. If there is no color bleeding from it the next day, then there isn’t any risk to your scrapbook. But if you do see color in the water, or collecting at the bottom of the glass then don’t use that fabric in your scrapbook at all. When using glitter, be sure there is a top layer of spray adhesive to lock them down, or better yet use special glitter glue where the glitter is mixed right in. If this is not done right the glitter will slowly fall off, and loose glitter means scratched photos. After you have planned the layout for your photos, be sure that you are using the right kind of mounting tape for them! Regular mounting tape is fine for buttons and bottle caps, but when it comes to mounting photos you need to use special photo mounting tape which is completely acid-free. Ultimate Small Shop Member If you don’t, your photos will slowly discolor. The tape should say “acid-free” right on the packaging.
For those of us building apps, there's an increasingly larger burden on us to meet the expectations of our users. We've outlined the considerations of what makes a great app in the past, which are more relevant than ever. Users simply don't have the patience for apps that are overly complex, slow, or buggy. The best apps are personalized, highly contextualized, and touch human emotion. Meeting those user expectations is significantly challenging.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
If you live where summers get hot and humid, you may need more than a fan to keep cool in your workshop. Fortunately, air conditioners will both dehumidify and cool your space — and you don’t need a traditional window to get the job done. Instead of a residential window unit, consider a freestanding portable air conditioner that you can use as needed on hot days.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
Just stumbled across your article and it’s right on time as I am about to launch a special events venue (ballrooms, meeting rooms, outside garden area, outsourced caterer, etc). Not sure what type of zoning this business falls under. I read that zones are usually for office, retail, industrial and leisure. Any idea what type of zone I should be looking for? Also first time trying to get a commercial space for this type of business, any specific suggestions?
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.

One of the most heavily used tools in your shop will be your table saw.  It is absolutely essential for ripping stock to size, working with composite material (like plywood and MDF), and venturing into the world of wood working jigs.  Budget is a limiting factor in a $500 build, but at $150 it is hard to pass up adding this Craftsman saw to your shop - even with limited funds.  
Once you have an idea of your store layout and a product mapping plan, it’s time to consider your store fixtures and displays. Fixtures are permanent—fixed—parts of your store such as lighting, counters, fixed shelving units, and dressing rooms. Displays hold product and tend to be movable, versatile, and customizable, like modular units, gondolas, tables, slatwall, and clothing racks.
In order to ensure that the staff you’re bringing on board is the right fit for your small business, there’s a few questions that you should ask yourself during the interview process. Are they competent? Capable? Compatible and committed to your core business values? Do they fit in with the culture you are trying to build? And can you offer them fair compensation? Business expert and entrepreneur Alan E. Hall, calls this the 7 C’s to hiring. At the end of the day you want to look beyond the skills and experience they have on paper and make sure that they are willing and able to grow with your business.
Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
Now, photographs or video tape will also be very useful especially to pass along to your insurance adjustor. Now the problem is this documentation won’t help you at all if it’s lost or destroyed so consider saving your information electronically. Take your photos with a digital camera and create a list of all your valuables, and save both in a computer file. This file can be saved to a disk you can keep at work or upload it to a website that you can access it from anywhere including your home.
Back in the 1970s and treeplanting in Oregon, I and Tony Lessa lived for two weeks at a time in the back of my 1954 Chevy PU. The canopy was just a simple shell with the board across next to the cab. After the fourth or fifth trip out in the season the accumulated funk was too much. You can imagine two hard-working guys in very muddy and cold conditions coming in after work with dirty wet gear. Pretty desperate circumstances but before Reagan trashed the treeplanting industry our coop ( Hoedads & then Second Growth) was making good money so we endured the hardships. It works for the young. Now, at 76, I find sleeping two of us between the wheel wells in a Dodge G. Caravan (seats removed) much too crowded. I think I will tent and the wife can have the van.
Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back.

Ralph has three decades of professional experience in using workshops and setting them up, and it certainly shows in his Ultimate Small Shop guide. You’ll find all the important information you need to put together your own workshop, including how to save money when putting one together; all the tools and equipment necessary to run a workshop; tips for choosing the best equipment; factors that should be considered when buying things for the workshop; and so much more. If you’ve considered setting up a workshop but feel you don’t have the time, space, or money – then you need to check out Ultimate Small Shop – How to Set Up a Complete Small Workshop on a Budget.
Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
In our opinion, the best kind of fridge you can get for a DIY campervan is a portable 12V fridge/freezer. These fridges are built for adventuring on 4x4 vehicles and boats. They’re very rugged, and they don’t need to be kept perfectly level like mini-fridges. They can run off 12V power or regular 110V. They keep your food as cold as you want, and they can operate as either a fridge or a freezer.
Amenities and Services – You’ll want to understand the full range of amenities offered by a commercial space. These amenities and services may include such things as communal rooms, free Wi-Fi, loading bays and docks, dining options, outdoor space, sewage and utilities, on-site security, and more. The zoning of your business will often dictate the type of amenities and services you require.
We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
×