A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.
I will challenge myself to use this space creatively to tell the story of each year. Ultimate Small Shop Guide When I started thinking of all the possibilities, it really inspired me to start getting organized and collecting some great memories. And don’t limit yourself to just photographs, your scrapbook pages can really be accentuated by other types of memories. Here are some ideas to get you started. Looking for some great Halloween crafts for your Halloween party, haunted house, or just for trick-or-treaters? A fun craft is something that can keep you occupied for hours on end especially if you enjoy it. Here are some ideas that will hopefully set you on your way in preparation for your next Halloween…If you live in a house that has a wood-burning fireplace, then chances are that you have access to tree stumps or large blocks of wood. These are great for making stands for your Jack O’Lanterns. You could use a chisel to slightly hollow out the middle of the stump so that the lantern can sit stably or simply use some Blu-Tack or Velcro. Get some small or mini pumpkins and hollow them out to use as candle holders. If open flames are out of the question, you can put glow sticks instead of candles for a different effect. You can carve, draw or paint faces on the pumpkins too. Instead of pumpkins, you could use apples as well. Ensure that you choose apples that sit well and flat or cut off the bottom to make a flat surface. Remove the stem and cut around it deep enough for the candle. It is best to use taper candles for a better fit. Get a large pumpkin and hollow it out to use as a salad bowl or to serve fresh vegetables. Cut off the top, hollow and clean it out and let it dry in the sun. You could carve a jagged edge design on the top. Do the same with some smaller or mini pumpkins to use for dips or salad dressings. Make a scarecrow in your front yard. You need two pieces of wood, one put into the ground and the other nailed across for the arms. Use old jeans and a shirt and stuff them with newspaper. Add some straw for effect. You can use a plastic pumpkin for the head and draw a face on it. This makes a great Halloween craft for the whole family. Tie glow sticks to helium balloons and let them float around the house. Ensure that some string extends below so that people can easily reach them if they get stuck somewhere or simply to play with them. Use publicly available Halloween fonts on your computer to make banners or invitations for your party. It’s a fast, easy Halloween craft you can use instantly to enhance your party theme. Ultimate Small Shop Book Print them onto inkjet iron-on transfer paper and put them onto your favorite t-shirt or Halloween outfit. A visit to your local hardware store for some basic items and you could make your own tombstones transforming your garden into an instant graveyard. Paint them grey to resemble stone. Do not worry about the details as it will be dark, but do put on some exciting or scary wordings. By the way, your local hardware store is loaded with Halloween craft ideas.
We did a lot of research and landed on the Bestek 300W Power Inverter. We usually had our devices plugged in while we were driving so they'd be charged by the time we parked for the night. And if we were ever really in a pinch, we would plug it in for 10 minutes with the car off, then another 10 minutes with the car running until it was sufficiently charged.
According to a recent digital marketing survey conducted by Clutch, 74%of small businesses surveyed had a company website. Of the businesses that said they do not have a website, 9% said they planned to build a website in the future, while 10% said that that they are unlikely to build one. One thing is clear, small business owners are starting to join the digital revolution and are reaping the rewards in terms of increased customer loyalty, growing word-of-mouth, and most importantly, increased sales.
The first is that they will need to be powered by a product catalog. Many times that already exists and an app will just leverage APIs or web services to pull back products. If it doesn't, however, it will require either a custom buildout (beware!) or leveraging platforms like Shopify, Magento, or comparable solutions. The strength of these tools include providing the administration interface to add new inventory, APIs or SDKs, ways to store items in a cart, and similar features. The downsides are that you'll be limited by their workflow and customizations.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
Well this is the same unit I have used for years so the noise level will be what it has been. I never turn it on without ear protection. In the future, I plan on building a little closet around the cyclone to help mitigate the noise to some extent. As for cycling the motor, I read that too. But the way I work, I just can’t do that. I have to turn it on and off as needed but I do try to limit it as much as possible by doing all of my heavy milling at once.
Store design experts advise small retailers to keep versatility in mind when choosing product displays. Your stock will likely change over the years. If you install permanent, unmovable displays, you will likely regret it later. Adjustable display options such as slatwall, gridwall, apparel racks, and shelving tend to be good choices for small retailers.

Let’s say you’re a Brooklyn-based hipster and you want to follow your lifelong dream of opening your very own artisanal, organic lemonade stand. You’re planning on stationing your retro lemonade stand along a busy road in Williamsburg, Brooklyn. And maybe you want to hire a couple of college kids to collect the money and serve your customers, (probably while wearing some painfully cool 1970s punk band t-shirts). You’re only thinking about it semi-seriously. It might be something you’re going to do when you’re not focusing on your real career as an aspiring DJ.
Fantastic build and opportunity for you. I really appreciate your humbleness given the great asset you have in the new shop. You flaunt/market what you do and where you do it because that’s the business you’re in, but at the same time you understand what a great tool you have in the shop itself relative to what most folks will ever acquire. Well done.

When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively win­dowless north walls may be a place to arrange wood storage or mechanicals.
In as much as I am a clamp freak, I needed some way to organize clamps without spending a mint on brackets. In our previous house we had a number of glass shelves –which I didn’t plan to put up here. But, the brackets were great – I laid in two tracks next to each other, then took a pair of the shelf brackets, cut a piece of 9/16 x 9/16 x 3 inch pieces of wood – put the wood between the brackets, shrunk wrapped around the brackets and wood, and came up with some really stable clamp hangers.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
×