For years my wife and I had agreed that we would one day leave Oklahoma for someplace we really loved. That day finally arrived last year when we found a home in Vancouver, Washington that met our dreams. Only thing missing was someplace for a woodshop. Well, there was a place, under a deck, but not a room. So, as part of the move we had a local contractor build a room that would one day be the wood shop. Fortunately there was already a door from the house into this area, and about half of the “walls” were there, in the form of concrete retaining walls.
Now this Super Pencil from C.H. Hanson does all of that and more. The entire pencil is made from a non toxic graphite composition so the whole thing is a writing surface with no wood around it to shave away. Super pencil marks are water and smudge resistant and because the composite is so durable it never needs sharpening even when you use it on rough materials like concrete.
This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obsta­cle such as a setback.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percent­age of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both dif­fer depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.

Great article, Ryan! I love the detailed explanations of the various options for sleeping. I consider myself a veteran “light-duty traveler” who stumbled across some of these things by accident over the years. My needs are different than yours (I’m usually traveling long distances for days and weeks at a time for work or vacation, so I usually don’t hunker down in a base camp very often), but I have a few questions and points to share:

We did a lot of research and landed on the Bestek 300W Power Inverter. We usually had our devices plugged in while we were driving so they'd be charged by the time we parked for the night. And if we were ever really in a pinch, we would plug it in for 10 minutes with the car off, then another 10 minutes with the car running until it was sufficiently charged.
The issue with the old shop was manufacturing capacity and layout. We get runs of 4 to 6 of the frames on the left in the last pic and sometimes frames twice that size. We were masters of having everything on wheels, which works for a while but it takes twice as long to build anything that way. Then the office ladies walk through the shop to the kitchen while you are grinding and complain about all the dust etc.
The ARB fridge 50-Qt Fridge is the best of the best. ARB is an Australian 4x4 accessories company, and all of their products are built to withstand just about anything. The ARB fridge is extremely rugged, and features powder-coated zinc steel construction for the ultimate in durability. It can take a beating, and works just fine on inclines up to 30°.

Workers’ compensation insurance is designed to provide wage replacement and medical and death benefits to employees who are injured or worse on the job. In exchange for these benefits, the employee gives up his or her rights to sue for liability leading to the accident. Your premium will reflect the type of business you operate and the average salary of your employees. Much like auto insurance, business owners who are new to starting a small business or those with less experience tend to pay higher premiums.


Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
Really enjoyed watching the video of the shop build. You will be turning out great pieces in no time. At the end of the video it looks like you have your dust collection system up and running. Where did you purchase the duct work? I thought I remember you talking about this in the old shop. Did you use regular HVAC 4″ round duct or a heavier piece. Thanks for the insight and good woodworking.
At least once a year I want you to set aside some time (I’m talking about a large chunk of time - like a day) and I want you to write down everything you want to accomplish this year or next year (or whenever you are planning for). I tend to plan for a whole year, but you can try 3-6 months to help you get started. Take away any and all distractions because it’s important that you are super focused on what you want to accomplish for the year. This is the time to let your ideas flow, don’t hold back. Things on this list can include: Launch your own website, release a new invitation line, and work on my Instagram account. Don’t overthink, just write down what comes to your mind and whatever your heart desires. There will be time later to refine what you have written down. When you are starting to brainstorm your goals, I would suggest that you first start off writing them on a notepad like this. And then once you are done, you can move them over to a task organizer like this.
Apps begin to get more complex—and costly—once user authentication is involved. The main reasons for that are all the other expectations that come with user authentication. Typically, they include interacting with data (e.g., favoriting an article), syncing data across devices, push notifications, and perhaps collaborative features (e.g., inviting a family member).
Once you’ve considered the questions in the previous paragraph, start thinking about how your products/services stack up against the local competition. Because unless you are offering something ground-breaking and innovative, chances are that your potential customers are currently having their needs met by another business. That means it’s going to be your job to convince them that Blue Sheep Bakery is a better option than Bob’s Bake Shop. If your first thought was to compete on price, sorry to break it to you but, that’s not going to cut it. There is more to starting a successful small business than matching the price to the guy down the street.
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
Do you have a business license? Do you have a permit to open a food service establishment issued by the local health department? Are you applying for a permit to modify the building you wish to occupy? Do you have a health permit from the county health department? Do you have a signage permit? How about an alarm permit from your city or county fire or police departments? These are just a few of the questions you need to ask yourself.
Another option to consider is an expensive but efficient Festool dust extractor. These dust extractors are designed to work with other Festool tools, but they also match up with most other brands' compact power tools as well. A nice thing about Festool's vacs is that the hoses dock neatly inside the units. There's almost nothing I value more for a compact shop than self-contained storage.
A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.

Next up are the chisels, you can start with a couple of sizes and build from there. When looking at saws, for joinery a dovetail saw is a good place to start, with a choice between western style or Japanese. For precise cuts across the grain, cutting tenon shoulders, and defining the edges of a dado a carcass saw also makes a good complement to the dovetail saw.


By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Hey thanks for the great insight on a pickup camping setup! I just purchased a 2002 tundra with a 74″ bed. Picking it up in Denver in a week and driving it to Durango and then around the southwest. I mainly decided on a truck for a mobile place to keep my dog(that doesn’t have an interior he can rip to shreds), but I am thinking of building a setup similar to yours. You haven’t used yours with a canine companion have you? Any suggestions on keeping it dog-friendly, dog-comfortable and dog-proof? I will be keeping him in the back while at work and such and will be camping in the back with him and possibly another person.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
You’ll also sometimes want to walk a property with a licensed contractor. This is because some commercial spaces require lease build outs, which are necessary additions or improvements to the space. Build outs can be fully or partially covered by the landlord. It’s important in this scenario that you get an accurate renovation estimate and negotiate a build out into your lease.
Seems simple right? Well, yes and no. Inventory management can become very complicated once you factor in issues like product lifecycle (how quickly do the apples go bad?), variable amounts of raw goods in a single item (how many apples went into that apple turnover you sold?), delivery times (how quickly you can get new apples?), and variable wholesale apple costs (how much did you pay for that particular bunch of apples?).
I got extra batteries for my cordless tools, but I could never remember which battery was newly charged and which was run down. Now I can easily tell them apart because I painted a number on each battery with my kid’s white nail polish. It dries fast and is— you got it—“tough as nails.” — Tom Baker. Plus: Learn how to double the life of your car battery.
I think the music comment was about speakers for playing music. I put a few 8″ in ceiling speakers in from MonoPrice.com ($60 / pair I think) and love them. A space that big would probably need at least 3 pairs. You’re not throwing a rock concert with them, but they provide very decent background music for not much cash. The speaker wire from MonoPrice is dirt cheap too. Just add a cheap receiver to drive them. Of course, you probably don’t want to spend that cash at the moment. But it’s a good starting point for the future.
Well, I thought about that I don’t want all that dust to kind of infiltrate everything else in the building. So actually instead of putting in some kind of dust collection system, I thought that I would probably just put a nice shop vac here. And then I have room that I can bring some hose back behind this column and then you know if you’re sitting here working on something we can have adapters that go right into a miter saw or right into a sander or have a little outlet more or less to lay up on the counter that would collect all of the dust. And the same thing could happen on any of the work we do out here.
It’s important that you have a fundamental understanding of what is making your business successful before you decide to expand. Who are your customers and why do they enjoy what you offer? Who are your suppliers and will they be able to deliver to your new location? What are your operating costs and will they be the same in a new location? A lot of small businesses start off in the suburbs of a town before making the move to a city’s business district, only to find that unexpected additional costs are swallowing up their profits.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”

Leslie recommends that retailers provide some type of seating for both customers and anyone who is accompanying them. Shoppers do get tired and so do their friends and relatives who are along for the ride. Why not offer them a chair? Seating can be as simple as stools near the checkout or a lounge area near the dressing rooms, like this fun setup below:
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
If your shop will be attached to your house or another struc­ture, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
This sturdy 30-in. x 6-ft.-long DIY workbench is the ultimate in simplicity. It’s made from only fifteen 8-ft.-long 2x4s and one sheet of 1/2-in. plywood. Learn how to build a workbench by following the cutting diagrams to cut the parts: Figure B to cut the plywood tops, then Figure C to cut all the framing. Use the lengths provided in the Cutting List (see Additional Information below). You can either screw the framing together with 3-in. screws or hand- or power-nail it together with 3-in. nails. Screw the plywood down with 1-5/8-in. screws.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
×