For now we’re just getting it out of the room so that our electrician can get started. In any kind of workshop you want plenty of access to power and lots of use of the light. So Mike our electrician is hooking us up. If a service call from an electrician isn’t in your budget you can plan your space so that you can best take advantage of the outlets that are already there. Now Mike has checked all of these surfaces to be sure they can handle these extra outlets he’s adding.

Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.

For this reason, on-demand applications can get very time intensive. Consider building on an on-demand platform on both iOS and Android. A typical app on a single platform would require one experience to be designed. In the case of an on-demand app on two platforms, four would be required. That's one experience for each user in the system (i.e., two per platform) plus each platform (i.e., four in total). On-demand apps also often require a number of administrative interfaces. The only way to reduce the cost of an on-demand platform is to streamline the typical feature set included. For example, you could remove in-app payments or administrative interfaces while doing market validation.
If customers naturally turn right when they enter, and you guide them to circle all the way around, you'll realize that the front left is probably the ideal location for your checkout counter. However, this decision also depends on the size and layout of the store itself, which means you'll have to use your best judgment on the most natural point to have that check-out counter.
You can see in this step how I notched each rafter to fit more securely to the walls.  I also used a metal hurricane strap to secure each rafter to the wall.  Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution.  The walls are a simple board and batten system.  The 1x3 trim covers the joints of the 4x8 OSB.  They make much more high quality sheets goods to use as siding.  However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet.  I sealed the OSB and painted it with exterior paint.  If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed.  It has held up very well over the past couple years and I see no need to spend more money on it now.
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.

This is about how I built my wood shop. We decided to move from our previous home for a variety of reasons. I saw the move as an opportunity to gain a bigger shop for my wood working hobby. The house we found had everything we wanted, except for a shop or even a garage. It did have a non functioning indoor pool. We thought this space would make a nice wood shop. I could just build a floor over the pool and have a shop. As we got further into the inspection process, it was looking as though fixing the structure over the pool was going to be expensive. It looked like we would have to put a bunch of money into a structure that was not really a wood shop and not a functioning pool either. It made more sense to take out the pool and structure, and then build a wood shop from the ground up. We started this project by regrading our side yard to gain access to the pool in the backyard. Once we had access, we took out the pool. We half filled the hole where the pool was with compacted gravel. I realized that if we sank the shop into the ground I could have the ceiling height I had always wanted in the shop and preserve the view from the house. The design of the shop is a box with a shed roof. The roof wraps down the east side of the structure. I like to think of it as a slightly open toolbox. The entire shop is laid out on a 24 inch grid. The windows and doors fall within this grid. I had a general contractor built the shell and then I built the windows and interior. The interior walls are comprised of a 34 inch concrete stem wall at the base. Above that is a 9 foot, plywood wall. In the space above the plywood wall and below the shed roof is poly carbonate panel to form a clerestory. The tool layout in the shop is divided into 4 areas: an area near the door for material storage and prep, a central area for general wood working, and two areas near the back of the shop, one for turning and one for metal working.


If you are just getting started in woodworking and want to know what tools you’ll need to set up shop, you’ll want to download this free PDF from Popular Woodworking. We have put together a complete list of basic woodworking tools to kick-start your new hobby. In this free download, you’ll get our recommendations for the best hand and power tools for beginners. Buy these tools and you’ll have everything you need to make great woodworking projects.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
The thing I wanted to mention was that I moved from Seattle to Loveland, Colorado north of Denver in July ’05. I brought my ’01 Dodge Ram 2500 with a 8.5′ Northland Grizzly slide-in camper. It was myself and my 9 year old Black Lab mix Lucy. One thing I had not anticipated was the temperatures here in Colorado. It was 105-106 degrees for the first week I was here. My job was in Boulder, which is known for its “bunny-higher” types. I couldn’t leave Lucy in the camper at the RV park because I didn’t have air conditioning in the camper. I took her to work with me and tied her long rope to the trailer hitch on the truck so she could crawl under it and get into the shade. I also put out plenty of cold water for her that I replenished often. By the afternoon of my first day at my new job I heard rumors that people were going to call Animal Control on me for having my dog outside in temperatures that hot, even though she had both shade and water. I ended up having to leave early my first day so I could go purchase a $600 air conditioner and install it in the camper so I could leave Lucy there during the day and I didn’t have to worry about her comfort.

To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
×