Note: Some of the links to products that we recommend on this page are affiliate links. This means that if you click through one of our links and buy something, we get a small commission at no cost to you. This helps us keep this blog going so we can continue to provide you with van build tips, tricks, and guides. We believe in honest opinions, and we never recommend anything we don't know about. Every recommended product on this page we've either used personally, have personal experience with, or have researched heavily.

Boy you guys are spoiled, lol. There will always be at least some echo in the shop. I wouldn’t judge the acoustics based on this video though since the shop was still being put together at the time. No cabinets and no floor tiles, so the echo is to be expected. Have you seen the latest video? http://www.thewoodwhisperer.co.....rock-star/ The sound is dramatically improved over the Dream Shop video and all I did so far was add a few floor mats here and there. By the time the cabinets are in and I get some nice rubber floor tiles in place, the sound should be at least to the level of the old shop if not better. Right now though, my priority is on building a bed and I do consider the current sound to be “acceptable” for web videos. I’ll focus on tweaking things when I finally get some spare time. Considering adding some acoustic tiles to the ceiling.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
As far as the batten, your actual question..haha. There has not been any moisture or rain make its way through. However, I did caulk all of those joints before I painted. I also made sure I primed all the exposed edges, especially the bottoms of the osb sheeting. You could probably put some pvc j channel along the bottom to prevent rain splash from absorbing up into the end grain. Just make sure you give a way to drain any water that makes it in the j channel. Does that make sense?
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Well this is the same unit I have used for years so the noise level will be what it has been. I never turn it on without ear protection. In the future, I plan on building a little closet around the cyclone to help mitigate the noise to some extent. As for cycling the motor, I read that too. But the way I work, I just can’t do that. I have to turn it on and off as needed but I do try to limit it as much as possible by doing all of my heavy milling at once.
Equity financing is money raised in exchange for a share of ownership in your business. The core benefit of this type of funding is the lack of debt. You won’t have to worry about those pesky monthly repayments. The downside? You are giving up total ownership of your business, you are giving up the rights to a portion of the ongoing profits of the business, and you are potentially giving up some control of how your business is run (Though this is not always the case).
As the old saying goes, the only two inevitable things in life are death and taxes. Almost all small businesses in the United States are subject to some form of corporate income or gross receipts tax on a state level — that is, unless you happen to be a lucky inhabitant of the great states of Wyoming, Nevada or South Dakota. Actually, even these states will require you to pay state workers' compensation insurance and unemployment insurance taxes. Oh, and of course every small business in the country is subject to some form of federal taxation.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
Ultimate Small Shop is a turnkey solution for woodworkers to get started with their dream workshop. Every woodworker, hobbyist or professional, wants a nice workshop in their home. It may be the garage or a shed, the barn or a detached man cave, the basement or a room up somewhere with enough space. Woodworkers often fail to create their dream workshops due to dearth of space and funds. Ultimate Small Shop solves both these issues and empowers woodworkers to live their dreams.

The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.


In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 
By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!
However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
However, since you may not have "aisles" per say in your store, it's still important to think about grouping products in a way that makes sense from a shopper's perspective. Also, remember to keep "higher-demand" products displayed at eye-level while placing lower-grossing products at the bottom or above eye level. Lastly, It's recommended that you change up these speed bumps weekly or regularly enough to create a continued sense of novelty for repeat visitors. 
A very simple countertop but one that should work great for our workshop, now we’ve already applied one coat of polyurethane to kind of seal up the plywood. Now we’ll be applying another coat once that dries to give it a little bit of durability because this thing will get a lot of abuse. Now Tim’s applying the same kind of clear sealer to our little rolling workbenches here, and I think this is a great idea, we’ll be able to roll these out, lock down the casters on the bottom then you can have a drill press or any other bench top tool that you can work on, then when you’re finished with them you can roll it right back, tuck them up against this wall and it serves as a good storage unit and gives you the chance to keep the workshop wide open for some of the larger projects we might be working on.
In order to ensure that the staff you’re bringing on board is the right fit for your small business, there’s a few questions that you should ask yourself during the interview process. Are they competent? Capable? Compatible and committed to your core business values? Do they fit in with the culture you are trying to build? And can you offer them fair compensation? Business expert and entrepreneur Alan E. Hall, calls this the 7 C’s to hiring. At the end of the day you want to look beyond the skills and experience they have on paper and make sure that they are willing and able to grow with your business.
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.

The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself). woodworking shop design
×