Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D modelling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experiment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you anticipate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.
Also, heard of anyone camping in an Accord sedan? I’m wondering if it’d be worth it to buy a new Tacoma to convert into a dirtbaggin’ vehicle or if I should try to make it in a sedan. Lots of variables… I’ve got the cash but it’d eat into the “cushion” I have for living on the road (about 50% of it). OTOH I could buy a used Tacoma, but they hold value so well it’d seem like long term it’d be best to get it new. I’ve seen some with 250 miles sell for $8,000+. Thoughts on getting a new truck using my beat-up sedan?
Lease build-out credits – These credits represent the ability for a tenant to make leasehold improvements in their commercial space at the expense of the landlord. These expansions and improvements are necessary for the successful operation of the business. With build-out credits, landlords either offer a reduced rent, reimburse the tenants, or pay directly out of pocket.
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.
It’s no accident that some of the best marketers in the tech startup industry are known as “growth hackers.” Think about your target demographic (e.g. students, local mothers, teenagers) and find any way you can to get the word out to them. Email mommy bloggers, hand out free samples at the local college, or write your website on all the napkins you hand out with your food. There is no substitute for action.
One tool that has been notably missing from the earlier builds is a router. There are so many reasons to own a router that I am not going to even try to list them. But if you want to get the creative juices flowing, take a look at this Pinterest page. The important thing to know is that this versatile tool can help you accomplish a number of tasks, everything from finishing edges to cutting dove tails.
If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
Congratulations on your new shop and all your success. I’ve watched all of your videos and someday if I have the money I would love to join your guild. I started a small workshop in my grandparents basement and someday I hope to start a small bussiness. Your website and videos have been the most informative and the most inspirational to me as a beginning woodworker. Thank you for sharing all your tips and hard work with people like me. I look forward to watching your videos for years to come.
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
The good news? There are a ton of free tools out there help you simplify and minimize the research required to secure your online identity. Among them is Namechk, a free username and domain search tool that helps you discover the availability of your business name across hundreds of social networks and domain extensions, all at once. Once you run a name search and confirm that it’s available for use both off and online, take the time secure your unique name both legally and on the web.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
When I change blades on my band saw, I usually need to adjust the thrust bearings and guides with an Allen wrench. I was tired of hunting around for the wrench, so I decided to stick it to the steel housing with a rare earth magnet (neodymium) about the size of a jacket button. Now it’s always handy! — Bill Wells. You can also use a magnet on your ladder.
I framed and sheathed each wall individually and then stood them up with the help of long 2x4 braces. My neighbor let me borrow his framing nailer, which made things go much faster. I added a second cap of 2x4 on the top to make the walls a little more rigid. I then laminated 4 2x4's to construct a ridgeboard. I nailed in some temporary 2x4 supports and had a friend help lift it into final position. Once all of the rafters are cut and nailed into place, the supports were removed.
Unfortunately, the requirements across the country and across different industries are as varied as the bodies enforcing them. The only way to guarantee that your licenses and permits are all squared away is to seek out regulating authorities on the county, state, and federal level, as well as consult with the relevant industry-specific bodies for your business type.
Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
Just stumbled across your article and it’s right on time as I am about to launch a special events venue (ballrooms, meeting rooms, outside garden area, outsourced caterer, etc). Not sure what type of zoning this business falls under. I read that zones are usually for office, retail, industrial and leisure. Any idea what type of zone I should be looking for? Also first time trying to get a commercial space for this type of business, any specific suggestions?
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.
There seems to be two things I like looking at and they are work benches & work shops. I too use my work shop for several other activities. I currently have a basement shop with a walk out entry, which is roughly 340 square feet and shaped like a flat s and has less than 8' ceiling height. In that shop I have an old Unisaw w/50"fence, 8" jointer, 15" planer, 10" sliding compound saw, 14" bandsaw and various & assorted power & hand tools. Also in the same space I have a small closet, dog grooming tub, & a space where a bathroom was roughed out. It is far from finished space and I have plans to put up a ship lapped paneled walls and fix up the closet for tool storage. I also plan on putting a cyclone in the bathroom space along with a tolet. I can work in the space as it is pretty well but the studded walls, insulation, & dust make the space somewhat uninviting.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
While the recession brought with it a well-documented squeeze on small business lending from banks, there are a number of alternative funding sources available to those who are starting or expanding their small business. Loans and/or equity investments can be sourced from multiple sources, including credit unions, savings and loans, and private financial companies. Family members, friends, and colleagues are also potential avenues to explore.
But if you want to do a lot of stealth camping in cities, a cargo van is your best option. There are so many of them on the road that people just don’t notice them, and they have a lot of floor space to play around with your perfect layout. But if you don’t plan on stealth camping and you value storage space and headroom, there may be better choices.
There are a number of woodworking fixtures you can get by without for a long while, but a sturdy workbench isn't one of them. The trouble is, those solid-hardwood benches we all lust after can completely blow a modest woodworking budget. Here's a bench that splits the difference. You'll get a top that can stand up to significant abuse, a sturdy, heavy base that keeps the bench planted where you put it, and an end vise and T-track system for holding workpieces as well as a variety of unique jigs. It may not look quite like a European bench, but it works just as hard as one for a lot less money.
Now, this is kind of an odd situation here, a few years ago when we bought this building there was a concrete block wall around here and a large drain right in the middle of the floor. Well the drain will certainly come in handy for any cleanup in the shop but the walls kind of left us when we removed those kind of left us a little divot and a little bit of damage here, so to make this nice and smooth so that our rolling workbenches will roll around real nicely we’re having to do a good bit of floor patch.
After you are done narrowing down your list of business goals, you are now ready to plan out when they will be accomplished. Just remember, nothing is set in stone so if you need to remove or add something to your business goals later down the road, that's okay. It happens to me ALL THE TIME. Sometimes our priorities shift or things didn't go as planned and you need to make changes.
Remember, your retail store layout guides product placement, directs customer flow, and defines the overall look and feel of your store, so it deserves plenty of thought. Many factors will affect your floor plan choice, including the size and shape of your sales floor, the types of products you sell, and even the customers you hope to attract. Keep these factors in mind as we explore each floor plan option in detail.