My plugs share breakers. I have them split up so there are no more than 2-3 receptacles on a single breaker. Ideally, each plug would indeed have its own breaker. But in a one-man shop where only one tool will be used at a time, I thought it would be more efficient and cost-effective to consolidate a bit. But the dust collector is on its own circuit since that will always run concurrently with other tools.
Electricity was something we didn’t want to worry about at all in our van, so we went big from the beginning. We bought Renogy's 400-watt solar kit and two VMAX 155ah batteries. We mounted three of the panels on our van’s roof, and the fourth we attached to a folding stand made out of PVC so we could roll it out as needed. While the system works great and keeps us charged up, in hindsight it was a little bit of overkill - especially since we added a battery isolator.
A great product line will also reflect a range of price points. For a business that is working hard to convey a sophisticated and elite vibe, it might be a useful strategy to set a high minimum price, but for the vast majority of small businesses, your pricing should be guided by one key thought: I want every single person who comes through my door to be able to find something that fits their budget.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
In my opinion, the best shop space is a flexible one. I know many folks expected that after setting up my shop so many times, I would be able to design the PERFECT shop space including a finishing room, a dust collection closet, and even some internal walls. But the truth is, the most important lesson I learned over the years was to expect change. My shop is not a static entity. It is more like a living breathing creature that adapts, evolves, grows, shrinks, and changes configuration. Committing to an internal spacial arrangement too early could yield disappointing results. This is why you won’t see me placing dust collection ductwork in the floor. I need to work in a space for at least a few months before I can be confident in my initial setup. Even then, I fully expect things to change at some point. If I made too many restrictive and/or permanent decisions ahead of time, these changes could be difficult or impossible to implement. So my best piece of advice is to forget about the concept of perfection. Instead, focus on flexibility. The ideal shop, in my mind, is little more than 4 walls, a roof, and a butt-load of outlets and lights. So here are some of my basic general goals for my new shop space.

Woodworking isn’t just an overnight hobby, for most it’s a fun pursuit that lasts a lifetime. As your skills develop, the workshop becomes a place not just to build but to repair along the way. In a world where people are strongly influenced by consumerism, there’s a tendency to revert to a throwaway culture. But if you can fix before throwing away, then your tools start to make a return on their investment and have a bigger impact.


Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
If you’ve been to gem shows, you know how overwhelming and daunting they can be. Although it’s difficult to narrow down all those tempting options, your jewelry business profit margin will be greater if you plan ahead and focus on shopping for a particular line and color scheme of jewelry. Ultimate Small Shop Online Review You must keep the bigger picture in mind and try to keep your emotions out of the design process. Here are some tips for defining your market and researching it so that you can walk in and out of a gemstone show feeling confident in the business investments you’ve just made. Gemstone shows and fairs are marketplaces for vendors of gemstones, findings, jewelry supplies, and tools. Due to a large amount of competition between the vendors, prices tend to be competitive. I’ve found unbelievable deals on high-quality gemstones and findings at gem shows. To find gem shows near you, you can simply do a Google search for “gemstone show” or “gem fair”. Other sources of information are your local convention and visitors’ bureau and any lapidary clubs in your area. Anyone can attend most gemstone shows. Although you don’t usually need a wholesale license to get in, some vendors may ask for your resale permit before letting you buy at wholesale prices. Show admission fees tend to be in the $5 to $10 dollar range. What market are you trying to target with your jewelry? Don’t try to please everyone. Ultimate Small Shop does it really work Are you trying to appeal to individuals like yourself? What age bracket are you trying to reach? Does your jewelry line appeal to funky or traditional individuals? Next, take a trip to your local department store and take note of the colors that are being used for the upcoming season. Look at the jewelry and observe the lengths of the earrings/necklaces, the sizes of the stones, and the other various style elements for the season. While your designs should not be copies or replicas of the jewelry in the stores, you can simply incorporate the observations you make into your own original design ideas. Fashion and jewelry magazines are also a great place to find out what trends are coming into the stores. There will be an overwhelming array of gemstones and supplies at the show. Having a jewelry line style and color scheme in mind will allow you to narrow your focus. Vendors will offer gemstones in more shapes, sizes, cuts, and colors than you can imagine. Stick to the colors you’ve mapped out for yourself and walk through the entire gem show once before buying anything. Jot down and compare the prices of items that you’re interested in. Then take a break, go outside for some fresh air, and reflect on the items you saw and really liked. Then review your budget and the jewelry line you have in mind before returning into the gemstone show. Ultimate Small Shop Guide Download This will help you get the best deals on the items you’re most interested in so that you don’t blow your budget or become overwhelmed by the options. Soaring through the air, watching the clouds and the birds fly by.
Thanks! Yep, the canopy clamps and the grooves in the bed liner are the only things holding the side shelves and sleeping platform in place. You just pop off the clamps with a ratchet and the whole things lifts out / slides out easily. That’s what I did to treat the wood after construction, takes maybe 15 minutes to pop out. Very modular. It’s been in there for more than two years now, same wood, and everything is still looking good and working fine. I like it!
If you’ve got 220v, and want to get a seriously good TS, the Grizzly G1023RL is about the best bang for the buck in a 3hp industrial style cabinet saw…$1195/$1294 shipped. It’s not a necessity to have that much saw, but it’s close in price to many lesser saws, and is about all you’d ever need. If that’s more than you can stomach, and/or don’t have 220v, you’re limited to a TS that’ll run on a standard residential 110v outlet….again I’d look to a full size stationary saw. The typical contenders are the entry level price ranges are the Ridgid R4512, nearly identical Craftsman 21833, Steel City 35990, Porter Cable PCB270TS….all under $600. The next step up would include the Grizzly G0661, G0715P, Craftsman 22116 (by Steel City/Orion), Jet Proshop, General International, Rikon 10-201, and Powermatic offerings. These saws all have the potential to perform well…the end performance is largely dependent on how well you set them up, and what blade you choose.

If customers naturally turn right when they enter, and you guide them to circle all the way around, you'll realize that the front left is probably the ideal location for your checkout counter. However, this decision also depends on the size and layout of the store itself, which means you'll have to use your best judgment on the most natural point to have that check-out counter.


All this is why I recommend you buy the very best stuff available, even if it means going without certain tools initially. Although it wouldn’t be a disaster to spend $1000 on a whole bunch of inexpensive tools, what are you going to do when you’ve outgrown the capability of these tools and want to upgrade? You’ve now got to somehow get rid of the cheap stuff and replace it with something better. This isn’t easy and it’s always the most expensive way to go.
When registering your business name you should also consider whether or not you have plans to expand your local business nationally or online in the future. Registering your business with the state does not offer brand protection beyond the state it is registered in. For example: If Bob’s Bike Shop is registered in New York, no other business will be able to use that name in that state. However, someone in Idaho can still register their business as Bob’s Bike Shop. If you have aspirations that look beyond Main Street, USA and would like the option to expand nationally or on the web, you should consider trademarking your business. When you trademark your business name, it makes it a lot easier to recover property that infringes upon your brand. For example: If Bob’s Bike Shop in Ohio purchased the domain www.BobsBikeShop.com but Bob’s Bike Shop in New York trademarked that name, legally Bob’s Bike Shop in New York has the right to file a domain name dispute to get the domain name back from it’s current owner.
The solution to potentially wedged boards on a jointer is to add a planer to the mix.  A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface.  This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square.  As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.  ​
Other than that, you can’t have too much light — especially north light! — and you want accommodations for all the electricity you can imagine. Ceiling fans are a must. A good dust collection system is good, too. Don’t forget to plumb in for compressed air. Do NOT use hard PVC water pipe for compressed air — ever. If/when it breaks or ruptures, it explodes into tiny sharp glass-like shards. I know firsthand. I’ll tell you about it some other time. Think balloon popping!
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
Smaller speed bump displays (above) and larger merchandise outposts (below) placed along your store’s main traffic flow let you draw customer interest to certain products. Speed bumps let you feature new finds and hot sellers in eye-catching ways. Larger outposts are great for special price stock or product groupings such as seasonal features and branded collections.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
YouTube: I love this place! You can find video training's on just about everything! It can  help you with a lot of the tasks that you need to accomplish for your goal. So if you want to "sell products using Instagram" and one of the tasks is: post beautiful photos with text on my feed often, then you probably need to go on YouTube and search for "how to design an Instagram post, if you don't know the first thing about it. You can use YouTube to help you accomplish goals or tasks on your list that is out of your skill set. 
If you live where summers get hot and humid, you may need more than a fan to keep cool in your workshop. Fortunately, air conditioners will both dehumidify and cool your space — and you don’t need a traditional window to get the job done. Instead of a residential window unit, consider a freestanding portable air conditioner that you can use as needed on hot days.
Small business owners can maintain steady, manageable growth by keeping a firm eye on costs and always aggressively looking for ways to increase sales and grow their brand. It can be difficult to empower staff and managers around you, especially if you’ve spent a long time steering the ship alone, but it is an essential part of successful expansion. Stay open to suggestions from your managers while making your current business best practices clear to them.
The primary investment of any garage workshop are the tools. Protect your investment with a high quality tool chest that is neatly organized and (if needed) lockable. Look for smooth rolling ball-bearing drawers, and if you’re buying used, beware of rust and dirt that could corrode your tools. We recommend installing drawer mats to keep your tools from sliding around. They also give your tools a softer cushion to rest in.

A dust mask or respirator will protect you while you're working, but won't do anything to protect you or your family from suspended particles still in the air. For this reason, an air filter is an absolute must if you work with woods indoors (I know of guys who sneezed out sawdust after working too long without an air cleaner). It's possible to make your own air cleaner out of box fans and furnace filters, but retail air cleaners will usually be much more compact. If you go that route, we recommend Wen 3410 3-Speed Remote-Controlled Air Filtration System for smaller shops.


Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
Solar Shower. For easy, inexpensive showering in wilderness locations, nothing beats a good solar shower. This is basically a bag of water that you leave out in the sun until it heats up, then hang it from a high place and shower using the attached nozzle. 5-gallon solar showers should get you about 5 minutes of good water flow. There are also pricier but more convenient pump-operated solar showers that you can buy.
“Your sales floor is a living, breathing entity that needs to change—frequently—in order to flourish. It’s the retailer’s job to make that happen. If your store is filled with the latest and greatest products, but your sales are in a rut, it could be because your customers are bored. They come to your store not just to buy; they come for ideas and inspiration. And they come to be entertained—even when they don’t buy anything, that experience is what brings them back.”
Then there are material considerations, such as how to bring full-size sheets of plywood home to cut down to size (you don't). And safety and cleanup are two more concerns: Proper ventilation and dust collection, a cinch in a larger shop, can be quite a challenge (and a potential health hazard). Nevertheless, you can set up a great wood shop in a small space, and we'll show you what you need.
Garage spaces are usually not insulated, and garage doors on most homes have very poor insulation. That means it’ll inevitably be super hot and stuffy in the summer, and freezing cold in the winter. To be comfortable in your workshop you’ll need to take the extra step to insulate your garage and set up some space heaters, and some portable floor or window AC units. Having to wear a heavy coat while you work will impede your DIY efforts and nobody likes working in a sauna.

Boy you guys are spoiled, lol. There will always be at least some echo in the shop. I wouldn’t judge the acoustics based on this video though since the shop was still being put together at the time. No cabinets and no floor tiles, so the echo is to be expected. Have you seen the latest video? http://www.thewoodwhisperer.co.....rock-star/ The sound is dramatically improved over the Dream Shop video and all I did so far was add a few floor mats here and there. By the time the cabinets are in and I get some nice rubber floor tiles in place, the sound should be at least to the level of the old shop if not better. Right now though, my priority is on building a bed and I do consider the current sound to be “acceptable” for web videos. I’ll focus on tweaking things when I finally get some spare time. Considering adding some acoustic tiles to the ceiling.
Before you bid in an online auction, check the site’s rules of operation. At some sites, a winning bid is a binding contract, which can be a problem if you can’t inspect the tool before you purchase it. Don’t forget shipping costs. In some cases they can exceed the cost of the tool. Also, make sure the tool you’re buying will run on the power you have in your shop. Many former industrial tools run on 240v single-phase power. If your shop doesn’t have 240v service, you’ll need to factor in the cost of upgrading before deciding to buy. You don’t want to saddle yourself with a tool you can’t use, no matter how good the price.
YouTube: I love this place! You can find video training's on just about everything! It can  help you with a lot of the tasks that you need to accomplish for your goal. So if you want to "sell products using Instagram" and one of the tasks is: post beautiful photos with text on my feed often, then you probably need to go on YouTube and search for "how to design an Instagram post, if you don't know the first thing about it. You can use YouTube to help you accomplish goals or tasks on your list that is out of your skill set. 

I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.
We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.
If your shop will be attached to your house or another struc­ture, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
WOW that is a nice size shop! I am looking forward to more videos on the shop projects! We have been shopping for a house for over a year & have finally found one but it has nothing for me to use as my woodshop! I currently have a basement shop that’s 24×40 & it’s really huge for me I couldn’t imagine any bigger. Anyway I will be looking at building a new woodshop for myself (yes I am a female woodworker) & you have given me lots of great ideas so far. I am an Artist & wood is my preference, everything I make is quite small (no furniture or anything that big) but I have lots of specialty tools for what I do as well! Thank you for sharing your ideas & all that you do. Keep up the great work!
Since grid layouts are used in most grocery, big box, and convenience stores, they create a familiar feel to customers. However, due to this familiarity, they tend to impart a grab-and-go experience. A grid layout can be a good choice for small retailers who shelf-stock inventory in quantity, like toys, books, magazines, specialty foods, kitchenware, and home goods. However, it’s not ideal for retailers who want to create an upscale, branded environment that invites relaxed browsing.
There are certain sayings that hold true and when buying clamps and measuring equipment parting with cash for quality make sense. But which clamps? G, F, sash, spring or strap? There are so many clamps and measuring tools available. Let the project decide which ones you need. As a reassurance, our Axminster Trade Clamps come with a lifetime guarantee, so this is one investment that literally lasts that long.
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.

Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.


Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Whether it’s underwear in an apparel store or milk in a grocery store, the items customers need most usually are found near the back. Think about this next time you’re in a grocery store. As you walk to the back of the store to get milk, you funnel past coffee, cereal, and toilet paper. And the milk is right by the eggs and cheese. This is primary and secondary zone merchandising in action, and the reason people shopping for one item often leave with three or more.
Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.

My husband is always hounding me about wearing eye protection whenever I use power tools. (Admittedly, I could be more diligent about it.) So, he recently glued some small magnets to several pairs of safety glasses and stuck them on all the power tools in our garage that have metal housings. Now it’s fast and easy for me to grab the glasses when I need them, and I’m reminded that my husband loves me. — Lisa Yanda. Here’s the other must have safety gear every DIYer should own.
Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us.
The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
Gutting: We actually took on a pretty big project when we bought our van because it came with a preinstalled wheelchair lift that we had to remove. Unbolting all the parts took both of us working on it for a full day, and it wasn't the most glamorous job. The good part was that we were able to sell the lift and the reclining bench seat for a combined total of $260. If there's anything to remove from your van, do this first.
We love natural light as much as anyone, and the big windows in our van were something we were super excited about. But when you're living in a van, you'll want some privacy. Trust me. You'll also need curtains to keep out the lights when you're trying to sleep. Making your own curtains can seem like a daunting task, but it's not all that hard. (I speak as someone who had to look up a tutorial to operate a sewing machine!)

“Your sales floor is a living, breathing entity that needs to change—frequently—in order to flourish. It’s the retailer’s job to make that happen. If your store is filled with the latest and greatest products, but your sales are in a rut, it could be because your customers are bored. They come to your store not just to buy; they come for ideas and inspiration. And they come to be entertained—even when they don’t buy anything, that experience is what brings them back.”
×