Does it motivate you? This is a tricky one because sometimes we have to do the work that we don't want to do to become successful. On the other hand, if it doesn't motivate you, you just literally wasted your time writing it down because you wont complete it. Consider your skill set and desire to want to work on that goal to help you eliminate goals (because you can't do everything). 
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
When starting your small business, the type of business structure you choose will depend on three primary factors: liability, taxation, and record-keeping. Most small business owners begin their commercial life as a sole proprietor because it’s the easiest way to get started. In fact, if you’re in business and you haven’t taken any action to incorporate, you are most likely deemed a sole proprietor by default. You are entitled to all the profits of your business but also responsible for all its debts, losses, and liabilities.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Now that you have your goals mapped out and you know the exact tasks that will help you accomplish them, I want you to pick a day of the week (preferably Monday or Friday) and start planning the week ahead - don’t skip this step, never skip this step. Schedule which one these tasks will happen on what day of the week. So you are literally pulling the tasks from that spreadsheet and placing them into this weekly planner. It’s important to keep in mind deadlines (the ones you set for your goals and when they should be accomplished) and the amount of time it takes you to do a task. You may also want to write down which day it’s due, and who is responsible for this task (if you work with a team).
I'm in the same boat. In Florida, we don't have basements, so my dedicated portion of the garage is 10' x 12'. In that space I have very neatly packed: 8' bench, Cabinet saw with 50" fence, 18" bandsaw, Dust collector, Joint, Planer, Drill press, Compound miter saw and a medium-sized hanging tool cabinet that holds all my nielsen stuff. I find myself moving my stool several times an hour just to work... Can't wait to move into a new house some day!
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
Well, I thought about that I don’t want all that dust to kind of infiltrate everything else in the building. So actually instead of putting in some kind of dust collection system, I thought that I would probably just put a nice shop vac here. And then I have room that I can bring some hose back behind this column and then you know if you’re sitting here working on something we can have adapters that go right into a miter saw or right into a sander or have a little outlet more or less to lay up on the counter that would collect all of the dust. And the same thing could happen on any of the work we do out here.

In a small space, there's not much room for one-trick ponies: You need gear that can do many different things, and that goes for your work space and stands, too. You can add a wood clamp to a multifunction workbench, but you probably need compact work or tool-holding stands to make up for the lack of a large work surface. Occasionally you may need to take your work to another room or even outside, in which case portability is also important.
You can also make your store comfortable by incorporating a waiting area with comfy seats and benches to encourage customers to spend more time in your store. This is especially helpful for shoppers accompanied by someone who isn't interested in making a purchase. But keep the seats or benches facing the merchandise so that they're still top of mind for those lounging around in your store.  
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
Use the scrap piece of plywood to map out the angle for the speaker stand legs. Decide the height you want for the base of the speakers, and make a mark on the plywood (32 in. for us). Mark the depth of the speaker (13 in.). Lay the 1x4 board assembly on the plywood, lining it up with both the corner of the plywood and the 13 in. mark from the edge. Scribe along the 1x4 board assembly, take the assembly away, and find your angle with a protractor or speed square (17 degrees for us). Cut that angle onto one end of the 1x4 board assembly.
Using six pipe cleaners, you can make your own skeleton. Bend one pipe cleaner into two for the backbone. Twist another around the bottom of the backbone to make into the legs. Do the same for the arms. Join two pipe cleaners and twist them around the backbone leaving some space forming a ribcage. Ultimate Small Shop Woodworking Twist the last pipe cleaner for a head and glue on some eyes. Hang with a rubber band for a bouncing effect. Your kids will love making Halloween crafts with pipe cleaners. But be careful when cutting and keep them out of their mouth. Going trick or treating? Why not make a special jug to collect candies? Cut off the top two inches of a gallon milk jug. Soak to remove any labels. Paint orange. Once dry, paint or stick on eyes nose and mouth resembling a Jack O’Lantern. Use fluorescent paint for a nice effect. The jug can be kept for future reuse. Using glue and food coloring, you can make a see-through painting. Paint a Halloween image onto a piece of plastic wrap. Before the mixture dries, put another piece of plastic wrap on. Cut it out and hang it in front of a light source for a see-through effect. You could also frame the plastic pictures using wood or cardboard if you want them to be longer lasting. Make some hand printed spiders. Ralph Chapman Ultimate Small Shop Apply black paint to your palm and 4 fingers leaving out the thumb. Place palm onto a piece of paper. Turn the paper 180 degrees and print again making sure the palm overlaps. Add some wiggly eyes using either paint or sticks. This is suitable for even 2 or 3-year-olds. Make your own blood. It is less expensive than buying ready-made blood from the Halloween shops. It’s not difficult; all you need is Karo syrup and food coloring. While you’re at it, why not make some slime using glue, water, and borax powder. This is an advanced Halloween craft, so take your time and be careful. Using apples, you can make dried, shrunken heads. Peel the apples and coat with a mixture of lemon juice and salt to prevent browning. Carve out a face of eyes, nose, and mouth. Do not worry about the finer details as they will probably be lost when the apple dries. You can use whole cloves for the eyes and rice grains for the teeth. Let the apples sit out in a warm place for about 2 weeks. If you don’t have 2 weeks, you can speed up the drying by putting them into an oven on the lowest temperature for about 45 minutes and then dry out naturally for the next 2 days or so. Ultimate Small Garage Clock Shop Once dried, they shrink and deform into weird and scary looking faces. Says Angie Maroevich, “You don’t have to spend a fortune on commercial Halloween supplies to have a great party.

Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
×