It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
Concrete garage floors can work as a workshop surface, but over time they stain and you’ll end up tracking a lot of dust and dirt into your home. An epoxy floor finish is easier to clean and can also provide extra grip. For a softer surface that will help your joints when standing a long time, check out those restaurant grade rubber floor mats or some durable options that include garage floor tile.
Fantastic build and opportunity for you. I really appreciate your humbleness given the great asset you have in the new shop. You flaunt/market what you do and where you do it because that’s the business you’re in, but at the same time you understand what a great tool you have in the shop itself relative to what most folks will ever acquire. Well done.
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code conventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow foundation may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the concrete slab will structurally bear the weight of the shop structure you build above it.
But here’s a quick back-story so you know how things went down. The reason I moved my shop so many times was because the sale of our old house fell through at the last minute. This is the house with the original Wood Whisperer shop/garage. We took the house off the market to recuperate and wait for the market to improve. In the mean time, I decided that I should probably make the best of the shop space that I was already paying for, so that’s why I moved my tools back there. When we eventually put that house back on the market, it sold on the first day. That was a BIG surprise! While we weren’t financially (or mentally) ready to build the new shop, I wasn’t about to lose a chance to get that 2nd mortgage gorilla off my back. So all of our resources went into the sale of the old house and the purchase of my mom’s new place. Truth is, there really wasn’t much left to put toward the new shop. Thanks to some financing wizardry, we made it work. But let’s just say I’ll be paying this off for quite some time!
One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks!
With all the time and effort you've put into properly merchandising your products, the last thing you want is for incoming customers to hurry past them — this ultimately limits the number of products they'll purchase. One way retailers combat this is through creating breaks that force them to pause. These are sometimes referred to as "speed bumps." Essentially, this can be anything that gives customers a visual break and can be achieved through signage or special/seasonal displays.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40. A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits. As you work on a few projects you may find that more specialized bits are needed. But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
Congrats on a very nice shop. Great video to capture the moments. I too have moved around from place to place (in the Army) and I have to make my shop work with what they give me for a house. I’ve done work out of a tool shed and I make it work becuase I just love working with wood. Once I retire and settle in one spot I hope to get something similar to yours. I’ve picked up a lot of ideas watching this build.
If you dream of devoting your life to a cause you believe in, it might be time to start a nonprofit. You’ll need to incorporate your business and file for 501(c)(3) tax-exempt status -- and then you’ll be required to meet ongoing standards of compliance, but the payoff is making a meaningful impact on a cause you believe in. Want to do good while still making a profit? Consider social entrepreneurship.
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.