There are a number of woodworking fixtures you can get by without for a long while, but a sturdy workbench isn't one of them. The trouble is, those solid-hardwood benches we all lust after can completely blow a modest woodworking budget. Here's a bench that splits the difference. You'll get a top that can stand up to significant abuse, a sturdy, heavy base that keeps the bench planted where you put it, and an end vise and T-track system for holding workpieces as well as a variety of unique jigs. It may not look quite like a European bench, but it works just as hard as one for a lot less money.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
Listing agents are hired by a landlord to list their commercial property. Listing agents earn a commission that’s paid by the landlord, typically between 3% – 6% of the total lease. Tenant brokers, on the other hand, represent tenant interests. However, tenant brokers also typically earn a percentage of the overall commission paid by the landlord, knows as the tenant broker’s fee.
Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.

Once you’ve considered your commercial property options and their associated leases, it’s time to choose one or more commercial spaces and negotiate the leases. When formally entering into a commercial lease negotiation process, you’ll want to start by requesting the terms in writing. This request can come from you or your broker and is supplied by the landlord’s broker.

This is about how I built my wood shop. We decided to move from our previous home for a variety of reasons. I saw the move as an opportunity to gain a bigger shop for my wood working hobby. The house we found had everything we wanted, except for a shop or even a garage. It did have a non functioning indoor pool. We thought this space would make a nice wood shop. I could just build a floor over the pool and have a shop. As we got further into the inspection process, it was looking as though fixing the structure over the pool was going to be expensive. It looked like we would have to put a bunch of money into a structure that was not really a wood shop and not a functioning pool either. It made more sense to take out the pool and structure, and then build a wood shop from the ground up. We started this project by regrading our side yard to gain access to the pool in the backyard. Once we had access, we took out the pool. We half filled the hole where the pool was with compacted gravel. I realized that if we sank the shop into the ground I could have the ceiling height I had always wanted in the shop and preserve the view from the house. The design of the shop is a box with a shed roof. The roof wraps down the east side of the structure. I like to think of it as a slightly open toolbox. The entire shop is laid out on a 24 inch grid. The windows and doors fall within this grid. I had a general contractor built the shell and then I built the windows and interior. The interior walls are comprised of a 34 inch concrete stem wall at the base. Above that is a 9 foot, plywood wall. In the space above the plywood wall and below the shed roof is poly carbonate panel to form a clerestory. The tool layout in the shop is divided into 4 areas: an area near the door for material storage and prep, a central area for general wood working, and two areas near the back of the shop, one for turning and one for metal working.
I think the music comment was about speakers for playing music. I put a few 8″ in ceiling speakers in from MonoPrice.com ($60 / pair I think) and love them. A space that big would probably need at least 3 pairs. You’re not throwing a rock concert with them, but they provide very decent background music for not much cash. The speaker wire from MonoPrice is dirt cheap too. Just add a cheap receiver to drive them. Of course, you probably don’t want to spend that cash at the moment. But it’s a good starting point for the future.
Commercial law exists for one simple reason: money and trust have a long and storied history of mixing like oil and water. Throughout the millennia-long history of commerce, aspiring businessmen and women have been lied to, cheated, scammed, cajoled, bullied, and otherwise disconnected from every single dime they had by unscrupulous suppliers, greedy investors, and dishonest business partners.  

Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Keep your air hose and fittings in one place and out of the way. Screw a coffee can onto a scrap piece of plywood. Attach a 2-1/2 in. riser block to the edge of the plywood and hang the entire contraption from a wall or work-bench. Drape your air hose over the coffee can, and store your fittings inside. It also works great for hanging extension cords. — Walter Barndt. Build an air compressor cart.
I will challenge myself to use this space creatively to tell the story of each year. Ultimate Small Shop Guide When I started thinking of all the possibilities, it really inspired me to start getting organized and collecting some great memories. And don’t limit yourself to just photographs, your scrapbook pages can really be accentuated by other types of memories. Here are some ideas to get you started. Looking for some great Halloween crafts for your Halloween party, haunted house, or just for trick-or-treaters? A fun craft is something that can keep you occupied for hours on end especially if you enjoy it. Here are some ideas that will hopefully set you on your way in preparation for your next Halloween…If you live in a house that has a wood-burning fireplace, then chances are that you have access to tree stumps or large blocks of wood. These are great for making stands for your Jack O’Lanterns. You could use a chisel to slightly hollow out the middle of the stump so that the lantern can sit stably or simply use some Blu-Tack or Velcro. Get some small or mini pumpkins and hollow them out to use as candle holders. If open flames are out of the question, you can put glow sticks instead of candles for a different effect. You can carve, draw or paint faces on the pumpkins too. Instead of pumpkins, you could use apples as well. Ensure that you choose apples that sit well and flat or cut off the bottom to make a flat surface. Remove the stem and cut around it deep enough for the candle. It is best to use taper candles for a better fit. Get a large pumpkin and hollow it out to use as a salad bowl or to serve fresh vegetables. Cut off the top, hollow and clean it out and let it dry in the sun. You could carve a jagged edge design on the top. Do the same with some smaller or mini pumpkins to use for dips or salad dressings. Make a scarecrow in your front yard. You need two pieces of wood, one put into the ground and the other nailed across for the arms. Use old jeans and a shirt and stuff them with newspaper. Add some straw for effect. You can use a plastic pumpkin for the head and draw a face on it. This makes a great Halloween craft for the whole family. Tie glow sticks to helium balloons and let them float around the house. Ensure that some string extends below so that people can easily reach them if they get stuck somewhere or simply to play with them. Use publicly available Halloween fonts on your computer to make banners or invitations for your party. It’s a fast, easy Halloween craft you can use instantly to enhance your party theme. Ultimate Small Shop Book Print them onto inkjet iron-on transfer paper and put them onto your favorite t-shirt or Halloween outfit. A visit to your local hardware store for some basic items and you could make your own tombstones transforming your garden into an instant graveyard. Paint them grey to resemble stone. Do not worry about the details as it will be dark, but do put on some exciting or scary wordings. By the way, your local hardware store is loaded with Halloween craft ideas.

If you want that homey cabin feel inside your van, then lining the walls and/or ceiling with tongue-and-groove paneling is a good choice. Paneling looks awesome - the cedar paneling on our ceiling is one of the defining features of our van. And we cut ours to random lengths and stained it several colors to really give it that mismatched, rustic look.


Best-selling products should be placed in Primary Zones located toward the rear of the store, ensuring that shoppers will pass by Secondary Zones featuring other merchandise, increasing their exposure and sales potential (it’s why milk is always in the back of the grocery store!). You can also feature several ‘best sellers’ in window displays for exposure.”
The small apparel boutique pictured above really nails these traffic flow details! A roomy entrance offers clear sight and travel lines to eye-catching power walls on the right, and an inviting seating area towards the back. These lure customers into the store with the promise of treasures and comfort within. The shop even has a left-side checkout midway back. Someone really did their customer behavior homework on this retail store layout.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.

After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
I will also typically secure those sorts of items under my locked platform if I am gone for a few days in the backcountry, because in reality I could probably care less if someone broke in and stole my box of food, versus someone who stole my clothes or expensive down jackets, which would be much more problematic (and costly) to replace on the road.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
Apps in this scenario would be able to fully function without any sort of network connection. Historically, examples of standalone apps might be your settings app or the camera app that comes with your device. Even today though, those apps usually have some interaction with the network. For example, you can share a photo from your camera via messaging.
According to a recent digital marketing survey conducted by Clutch, 74%of small businesses surveyed had a company website. Of the businesses that said they do not have a website, 9% said they planned to build a website in the future, while 10% said that that they are unlikely to build one. One thing is clear, small business owners are starting to join the digital revolution and are reaping the rewards in terms of increased customer loyalty, growing word-of-mouth, and most importantly, increased sales.

If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
Excessive growth is of course, a good problem to have. However, after stabilizing from the startup process, small businesses more commonly grow steadily before approaching a plateau. This is completely normal and it is often at this point that you’ll need to go back to your business plan and carry out what is known as a SWOT analysis. This includes an analysis of a company’s current finances, the competition, and SWOT: Strengths, Weaknesses, Opportunities, and Threats. Renovation of your product line, rebranding, and seeking investment for expansion are all potential results of this SWOT analysis. Once again, the key here is being data-driven and always staying hungry. The successful small business owner is always looking for the incremental improvements in their business that when added up, make all the difference.
He’s also providing power to a cool light grid we’re building from several old fluorescent fixtures that we salvaged from past remodeling jobs. With six four-tube fixtures, we should get plenty of light. In a work space you want to install these lights high enough so they don’t get in your way when you’re moving materials but low enough to provide good even light.
When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time.  It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years.  During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.  

Unfortunately, the requirements across the country and across different industries are as varied as the bodies enforcing them. The only way to guarantee that your licenses and permits are all squared away is to seek out regulating authorities on the county, state, and federal level, as well as consult with the relevant industry-specific bodies for your business type.


I framed and sheathed each wall individually and then stood them up with the help of long 2x4 braces.  My neighbor let me borrow his framing nailer, which made things go much faster.  I added a second cap of 2x4 on the top to make the walls a little more rigid.  I then laminated 4 2x4's to construct a ridgeboard.  I nailed in some temporary 2x4 supports and had a friend help lift it into final position.  Once all of the rafters are cut and nailed into place, the supports were removed.
Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.

It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.

I think it would work pretty well for a music festival, I don’t see why not. I wouldn’t say it is robbery proof, but generally robbers are looking for quick and easy targets, like a purse sitting on the front seat, just smash and grab. If someone really wanted to rob what was under they platform, they surely could, but they’d need more tools and more time to do so. And they don’t even know if there is anything good under there… I’d like to think of it as a really good robbery deterrent.
It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.
Boy you guys are spoiled, lol. There will always be at least some echo in the shop. I wouldn’t judge the acoustics based on this video though since the shop was still being put together at the time. No cabinets and no floor tiles, so the echo is to be expected. Have you seen the latest video? http://www.thewoodwhisperer.co.....rock-star/ The sound is dramatically improved over the Dream Shop video and all I did so far was add a few floor mats here and there. By the time the cabinets are in and I get some nice rubber floor tiles in place, the sound should be at least to the level of the old shop if not better. Right now though, my priority is on building a bed and I do consider the current sound to be “acceptable” for web videos. I’ll focus on tweaking things when I finally get some spare time. Considering adding some acoustic tiles to the ceiling.
×