Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
BEST ANSWER: Hi, I probably can't help, depending on where you are in the process. If the bench in the photo looks like it's just what you need, you should download the plan. I think Rockler has several ready to assemble benches that look quite good. Example: Large Workbench (N2000) Item #: 31719... I. too, am retired and trying to decide whether to buy or build. I have a bench that looks good and works good, but just is too light for hand work. It all depends on what you expect to be using the bench for. There are some good books out there to help us decide. "The Workbench" by Lon Schleining" is excellent. Also, Christopher Schwarz has written several good books on the subject. Vince, good luck and have fun working wood.
A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
I will challenge myself to use this space creatively to tell the story of each year. Ultimate Small Shop Guide When I started thinking of all the possibilities, it really inspired me to start getting organized and collecting some great memories. And don’t limit yourself to just photographs, your scrapbook pages can really be accentuated by other types of memories. Here are some ideas to get you started. Looking for some great Halloween crafts for your Halloween party, haunted house, or just for trick-or-treaters? A fun craft is something that can keep you occupied for hours on end especially if you enjoy it. Here are some ideas that will hopefully set you on your way in preparation for your next Halloween…If you live in a house that has a wood-burning fireplace, then chances are that you have access to tree stumps or large blocks of wood. These are great for making stands for your Jack O’Lanterns. You could use a chisel to slightly hollow out the middle of the stump so that the lantern can sit stably or simply use some Blu-Tack or Velcro. Get some small or mini pumpkins and hollow them out to use as candle holders. If open flames are out of the question, you can put glow sticks instead of candles for a different effect. You can carve, draw or paint faces on the pumpkins too. Instead of pumpkins, you could use apples as well. Ensure that you choose apples that sit well and flat or cut off the bottom to make a flat surface. Remove the stem and cut around it deep enough for the candle. It is best to use taper candles for a better fit. Get a large pumpkin and hollow it out to use as a salad bowl or to serve fresh vegetables. Cut off the top, hollow and clean it out and let it dry in the sun. You could carve a jagged edge design on the top. Do the same with some smaller or mini pumpkins to use for dips or salad dressings. Make a scarecrow in your front yard. You need two pieces of wood, one put into the ground and the other nailed across for the arms. Use old jeans and a shirt and stuff them with newspaper. Add some straw for effect. You can use a plastic pumpkin for the head and draw a face on it. This makes a great Halloween craft for the whole family. Tie glow sticks to helium balloons and let them float around the house. Ensure that some string extends below so that people can easily reach them if they get stuck somewhere or simply to play with them. Use publicly available Halloween fonts on your computer to make banners or invitations for your party. It’s a fast, easy Halloween craft you can use instantly to enhance your party theme. Ultimate Small Shop Book Print them onto inkjet iron-on transfer paper and put them onto your favorite t-shirt or Halloween outfit. A visit to your local hardware store for some basic items and you could make your own tombstones transforming your garden into an instant graveyard. Paint them grey to resemble stone. Do not worry about the details as it will be dark, but do put on some exciting or scary wordings. By the way, your local hardware store is loaded with Halloween craft ideas.
When you are looking for small business funding options, be it from the local bank, an angel investor, or even a family member, the first thing you will be asked to present after your business plan will be any existing financial records. Make sure you are putting your best foot forward by keeping meticulous records, with your business finances completely separate from your personal finances.
Does it motivate you? This is a tricky one because sometimes we have to do the work that we don't want to do to become successful. On the other hand, if it doesn't motivate you, you just literally wasted your time writing it down because you wont complete it. Consider your skill set and desire to want to work on that goal to help you eliminate goals (because you can't do everything).
Assume that there aren’t any decent tools on craigslist or at garage sales, and keep in mind that I have absolutely no tools, dust collection, shop-vac, clamps, sanding & painting accessories, tables, materials to build my own tables/stands/jigs, or anything else—not even safety gear (you’re such a good buddy that you even let me borrow your extra set of goggles and your earmuffs when I used to come over).
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.
Every shop should have good lighting, whether natural or artificial. My video work dictates limited natural light, so I was sure to have plenty of overhead T8 fixtures (6500k). You’ll hear me mention in the video that I was disappointed to see that the ends of the shop were just a little dark. Thankfully, I was able to get the contractor to come back in and drop in 4 more fixtures for me, two at either end. Now the light is bright, crisp, and evenly distributed from one side of the shop to the other.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.